User's manual BoltGATE 20-31 Modular IoT Edge Gateway for Rolling Stock Original instructions – Rev: 1-6 2022.07.28 – EN Code: BTGATE-20-31_MAN_EN_1-6 FOR SAFE AND PROPER USE, FOLLOW THESE INSTRUCTIONS. KEEP THEM FOR FUTURE REFERENCE.
BoltGATE 20-31 User's manual EN Intended audience of this document This document is intended for system integrators. System integrator is a term applied to skilled persons who are specialized in linking together, physically or functionally, different computing systems and software applications to operate as a coordinated whole in compliance with the applicable regulations.
BoltGATE 20-31 User's manual EN How to get started HOW TO GET STARTED To get started with the BoltGATE 20-31 complete this procedure:: 1. Read carefully and understand the instructions and warnings contained in this User's manual. To lower the risk of personal injury, electric shock, fire, or damage to equipment, observe the instructions and warnings contained in this manual. For more information, refer to: "Safety-related information" on page 9.
(This page is intentionally left blank)
BoltGATE 20-31 User's manual EN Contents CONTENTS Intended audience of this document How to get technical support Trademarks Revision history 2 2 2 2 How to get started 3 Contents 5 1 Safety-related information 1.1 Important information 1.2 Explanation of messages 1.3 Safety instructions 1.3.1 Power supply safety instructions 1.3.2 Wireless safety instructions 1.3.3 Product handling safety instructions: product's surfaces may become hot 9 10 10 11 11 11 11 2 Consignes de sécurité 2.
Contents BoltGATE 20-31 User's manual EN 6.2.2 RoHS 3 compliance 6.2.3 Packaging and packaging waste 6.2.4 Product disposal and recycling 6.2.5 RED compliance 6.3 UKCA marking 6.4 FCC compliance 6.4.1 FCC marking 6.4.2 FCC compliance: Class B Digital Device 6.4.3 RF radiation exposure statement 6.4.4 FCC restrictions on 5 GHz Wi-Fi usage 6.4.5 FCC labeling information 6.5 ISED Canada compliance 6.5.1 ISED compliance: Class B Digital Device 6.5.2 RF radiation exposure statement 6.5.
BoltGATE 20-31 User's manual EN Contents 9.1.4 Earth connection terminal specifications 9.2 BoltIO 20-31 LED indicator 73 74 10 BoltSER 20-31 interfaces 10.1 BoltSER 20-31 connectors 10.1.1 Serial Ports characteristics 10.1.2 CAN Port characteristics 10.1.3 Earth connection terminal specifications 10.2 BoltSER 20-31 LED indicator 75 76 76 76 78 79 11 Product installation and power supply 11.1 Introduction 11.2 How to install the product on a DIN Rail 11.3 How to remove the product from a DIN Rail 11.
(This page is intentionally left blank)
BoltGATE 20-31 User's manual EN 1 1 Safety-related information SAFETY-RELATED INFORMATION This chapter gives the following information: 1.1 Important information 10 1.2 Explanation of messages 10 1.3 Safety instructions 11 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
1 Safety-related information 1.1 BoltGATE 20-31 User's manual EN Important information For safe and proper use, obey these instructions. Keep them for future reference. Failure to obey these instructions, violates the standards of safety, design, manufacture, and intended use of the product. Eurotech assume no liability for damages caused by failure to obey these instructions. If you have questions about these instructions, refer to: https://www.eurotech.com/en/support.
BoltGATE 20-31 User's manual EN 1.3 Safety instructions 1.3.1 Power supply safety instructions 1 Safety-related information WARNING Risk of electric shock. Failure to supply power correctly could result in death or serious injury, and could damage the equipment or other property. Refer to "What to do before you supply power to the product" below. 1.3.1.
(This page is intentionally left blank)
BoltGATE 20-31 User's manual EN 2 2 Consignes de sécurité CONSIGNES DE SÉCURITÉ Ce chapitre fournit les informations suivantes: 2.1 Informations importantes 14 2.2 Explication des messages 14 2.3 Instructions de sécurité 15 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
2 Consignes de sécurité 2.1 BoltGATE 20-31 User's manual EN Informations importantes Pour une utilisation sûre et correcte, suivre ces instructions. Les conserver pour référence ultérieure. Le non-respect de ces instructions constitue une violation des normes de sécurité, de conception, de fabrication et d'utilisation prévue du produit. Eurotech rejette toute responsabilité pour les dommages causés en cas de non-respect de ces instructions.
BoltGATE 20-31 User's manual EN 2 Consignes de sécurité 2.3 Instructions de sécurité 2.3.1 Précautions de sécurité pour l'alimentation électrique AVERTISSEMENT Risque de choc électrique. Une alimentation électrique incorrecte peut causer la mort ou des blessures graves, et peut endommager l'équipement ou d'autres biens. Voir "Que faire avant d'alimenter le produit en électricité" en dessous. 2.3.1.
(This page is intentionally left blank)
BoltGATE 20-31 User's manual EN 3 3 Technical terms and graphical symbols TECHNICAL TERMS AND GRAPHICAL SYMBOLS This chapter gives the following information: 3.1 Technical terms (acronyms, abbreviations) 18 3.2 Graphical symbols 18 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
3 Technical terms and graphical symbols 3.1 BoltGATE 20-31 User's manual EN Technical terms (acronyms, abbreviations) The following technical terms (acronyms, abbreviations) can be used in this User's manual: Term Meaning GND Ground # Active low signal + Positive signal; Positive signal in differential pair - Negative signal; Negative signal in differential pair 3.3 3.
BoltGATE 20-31 User's manual EN 4 4 Termes techniques et symboles graphiques TERMES TECHNIQUES ET SYMBOLES GRAPHIQUES Ce chapitre fournit les informations suivantes: 4.1 Termes techniques (acronymes, abréviations) 20 4.2 Graphical symbols 20 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
4 Termes techniques et symboles graphiques 4.1 BoltGATE 20-31 User's manual EN Termes techniques (acronymes, abréviations) Les termes techniques suivants (acronymes, abréviations) peuvent être utilisés dans ce manuel: Terme GND Signification Terre # Signal bas actif + Signal positif ; signal positif dans la paire différentielle - Signal négatif ; Signal négatif dans la paire différentielle 3.
BoltGATE 20-31 User's manual EN 5 5 Product Overview PRODUCT OVERVIEW This chapter gives the following information: 5.1 Product description 22 5.2 Intended use and not allowed uses of the product 23 5.3 Technical specifications 24 5.4 Labels on the product 29 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
5 Product Overview 5.1 BoltGATE 20-31 User's manual EN Product description The BoltGATE 20-31 Family is a modular IoT Edge Gateway system, EN50155-certified, which addresses the challenges of the next-generation applications for smart transportation by combining hardware and software for Edge processing and Cloud connectivity.
BoltGATE 20-31 User's manual EN 5.2 5 Product Overview Intended use and not allowed uses of the product The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). 5.2.1 Intended use The product is a modular IoT Edge Gateway system, EN 50155 certified.
5 Product Overview BoltGATE 20-31 User's manual EN 5.3 Technical specifications 5.3.1 BoltGATE 20-31 Technical Specifications Specifications Description (according to BTGATE-20-31-xy versions) Version -11 Version -21 Version -31 PROCESSOR CPU Intel Atom x5-E3940, 1.60 GHz (1.80 GHz), Quad Core Intel Atom x5-E3930, 1.30 GHz (1.80 GHz), Dual Core Intel Atom x5-E3940, 1.60 GHz (1.
BoltGATE 20-31 User's manual EN 5 Product Overview Specifications Description (according to BTGATE-20-31-xy versions) Version -11 ENVIRONMENT Operating Temperature -40 to +85°C (EN 50155:2017, class OT4, ST1) Storage Temperature -40 to +85 °C Non-condensing Humidity CERTIFICATIONS Regulatory CE, FCC, ISED, UKCA EN 50155, EN 45545 Safety EN 62368-1, UL 60950(§) Environmental Wi-Fi / BT Radio Cellular Radio RoHS3, REACH - RED, FCC, ISED, UKCA RED, FCC, ISED, UKCA Ingress Protection IP30 Enc
5 Product Overview 5.3.2 BoltGATE 20-31 User's manual EN BoltAIR 20-31 Technical Specifications Specifications Description (according to BTAIR-20-31-11 version) WIRED INTERFACES Odometer 1x Odometer input connector RADIO INTERFACES Cellular 1x LTE Global Cat 4, 2G/3G Fallback Wi-Fi / BT WiFi 802.11 a/b/g/n, BLE 4.
BoltGATE 20-31 User's manual EN 5.3.3 5 Product Overview BoltIO 20-31 Technical Specifications Specifications Description WIRED INTERFACES Digital I/O Digital I/O: l 12x Digital Inputs l 4x Digital Inputs + 4x Digital Outputs l 12x Digital Outputs Isolation: l Inputs: 3.7kV l Outputs: 1.
5 Product Overview 5.3.4 BoltGATE 20-31 User's manual EN BoltSER 20-31 Technical Specifications Specifications WIRED INTERFACES Description Serial Ports Serial Ports: l 1x RS-232/422/485 serial port l 1x RS-232/422/485 serial port Isolation: 3.
BoltGATE 20-31 User's manual EN 5.4 Labels on the product 5.4.
5 Product Overview 5.4.3 BoltGATE 20-31 User's manual EN Labels on the BoltIO 20-31 The following labels are placed on the product: Label type and content Label position Product Label* l Eurotech logo l Manufacturer address l Product number l Serial number l Regulatory marks (CE and WEEE) l Power supply specifications** Rear side of the product Label example * Information included in the label depends on the product version ** The symbol stands for direct current 5.4.
BoltGATE 20-31 User's manual EN 6 6 Certifications CERTIFICATIONS This chapter gives the following information: 6.1 Declaration of Conformity 32 6.2 CE marking 32 6.3 UKCA marking 33 6.4 FCC compliance 34 6.5 ISED Canada compliance 36 6.6 Antennas list 38 6.7 REACH compliance 40 6.8 Rail - Rolling stock compliance 40 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
6 Certifications 6.1 BoltGATE 20-31 User's manual EN Declaration of Conformity Upon request, Eurotech can provide the product Declaration of Conformity. For more information, refer to the Eurotech Technical Support (https://www.eurotech.com/en/support). 6.2 CE marking This product is CE marked and complies with the essential requirements and other relevant requirements of the directives reported in the following sections.
BoltGATE 20-31 User's manual EN 6.2.5 6 Certifications RED compliance This product complies with the Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonization of the laws of the Member States relating to the making available on the market of radio equipment. Modification statement Eurotech does not approve any changes or modifications to this product by the user. Any changes or modifications could void the user’s authority to operate this product. 6.2.5.
6 Certifications BoltGATE 20-31 User's manual EN 6.4 FCC compliance 6.4.1 FCC marking This product is FCC marked and complies with the regulatory information reported in the following sections. Eurotech is not responsible for the use of the product together with equipment (for example: power supplies, personal computers, etc.) that are not FCC marked and not compliant with the requirements specified in this instructions for use.
BoltGATE 20-31 User's manual EN 6 Certifications Si néanmoins cet appareil cause des interférences nuisibles à la réception de la radio ou de la télévision, ce qui peut être déterminé en éteignant et en rallumant l'appareil, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes: l Réorienter ou déplacer l'antenne de réception l Augmenter la distance entre le produit et le récepteur l Brancher l'appareil sur une prise de courant différente de celle à la
6 Certifications 6.5 BoltGATE 20-31 User's manual EN ISED Canada compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
BoltGATE 20-31 User's manual EN 6.5.3 6 Certifications ISED restrictions on 5 GHz Wi-Fi usage The product is limited to indoor operation and can only be operated in the frequency bands: 5150 MHz – 5250 MHz and 5745 MHz – 5825 MHz. Le produit est limité à un fonctionnement en intérieur et ne peut être utilisé que dans les bandes de fréquences 5150 MHz – 5250 MHz et 5745 MHz – 5825 MHz. 6.5.
6 Certifications BoltGATE 20-31 User's manual EN 6.6 Antennas list 6.6.1 Antennas list for CE compliance NOTICE Within the EU, use the antennas in compliance with the RED requirements. The BoltGATE 20-31 has been CE certified with the following antennas: Types Types Manufacturer and Model Fabricant et Modèle Bands (MHz) Bandes (MHz) Wi-Fi/BT Taoglas MA950.A.LBICG.005 Cellular Peak Gain (dBi) Max. Gain (dBi) VSWR 2400 - 2500 4900 - 5850 4.35 4.
BoltGATE 20-31 User's manual EN 6.6.2 6 Certifications Antennas list for FCC/ISED compliance NOTICE Within the US/Canada, use the antennas in compliance with the FCC/ISED requirements. Aux États-Unis et au Canada, les antennes doivent être utilisées conformément aux exigences de la FCC/ISED.
6 Certifications 6.7 BoltGATE 20-31 User's manual EN REACH compliance This product is assessed to be compliant with the regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), with the exceptions allowed by the EU Technical Committee. Eurotech has set in place a monitoring process to assess compliance to REACH regulation.
BoltGATE 20-31 User's manual EN 7 7 Main CPU Module interfaces MAIN CPU MODULE INTERFACES This chapter gives the following information: 7.1 Main CPU Module connectors (vers: -11) 42 7.2 Main CPU Module connectors (vers: -21 and -31) 43 7.3 Main CPU Modules Interfaces 44 7.4 Main CPU Module LED indicators 54 7.5 Main CPU Module Service Panel and Service Interfaces 55 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
7 Main CPU Module interfaces 7.1 BoltGATE 20-31 User's manual EN Main CPU Module connectors (vers: -11) The Main CPU Module connectors are as follows: Ref # Label Description A USB0, USB1 USB 3.
BoltGATE 20-31 User's manual EN 7.2 7 Main CPU Module interfaces Main CPU Module connectors (vers: -21 and -31) The Main CPU Module connectors are as follows: Ref # Label Description A USB0, USB1 USB 3.
7 Main CPU Module interfaces 7.3 BoltGATE 20-31 User's manual EN Main CPU Modules Interfaces The interfaces availability depends on the Main CPU Modules version 7.3.1 USB0 and USB1: USB 3.0 connectors specifications Connector Layout: 7.3.2 Pin # Signal Type Description 1 VBUS 5 +5V 2 D- IO Data- 3 D+ IO Data+ 4 GND P Ground 5 SSRX- IO Full-duplex Receive Data- Connector Specifications: l USB 3.
BoltGATE 20-31 User's manual EN 7.3.
7 Main CPU Module interfaces 7.3.5 7.3.5.1 BoltGATE 20-31 User's manual EN Navigation system specifications Feature Description Receiver type 72-channel GNSS receiver with Untethered Dead Reckoning (UDR) GPS/QZSS L1 C/A, GLONASS L10FBeiDou B1I, Galileo E1B/CSBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN Navigation update rate Up to 30 Hz Position accuracy 2.5 m CEP Acquisition Cold starts: Aided starts: Reacquisition 26 s 3s 1s Sensitivity Tracking & Nav.
BoltGATE 20-31 User's manual EN 7.3.
7 Main CPU Module interfaces 7.3.6.1 BoltGATE 20-31 User's manual EN A1: Main antenna connector specifications Connector Layout: Connector Pinout: Pin # Description 1 Female inner pin contact 2 Female connector body (outer thread) Connector Specifications: l SMA connector l Gender: Female Mating Connector Specifications: l SMA connector l Gender: Male 7.3.6.
BoltGATE 20-31 User's manual EN 7.3.7 7 Main CPU Module interfaces Wi-Fi and BT specifications (vers: -21 and -31 only) NOTICE If the country code is in Europe, channels 12/13 of 2.4 GHz frequency are not available for station mode. Feature Description Frequency bands WLAN: l l l l l 2.4 GHz ISM Bands 2.412 - 2.472 GHz, 2.484 GHz 5.15 - 5.25 GHz (FCC UNII-low band) for US/Canada, Japan and Europe 5.25 - 5.35 GHz (FCC UNII-middle band) for US/Canada and Europe 5.47 - 5.725 GHz for Europe 5.725 - 5.
7 Main CPU Module interfaces BoltGATE 20-31 User's manual EN Feature Description RF receive Sensitivity (Typical) l l l l l 50 / 98 802.11a: 54M less than 68 dBm 802.11b: 11M less than 78 dBm 802.11g: 54M less than 68 dBm 802.11n 2.4G: o HT20 MCS7 less than 64 dBm o HT40 MCS7 less than 61 dBm 802.11n 5G: o HT20 MCS7 less than 64 dBm o HT40 MCS7 less than 61 dBm © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
BoltGATE 20-31 User's manual EN 7.3.7.1 7 Main CPU Module interfaces A3: Main antenna connector specifications Connector Layout: Connector Pinout: Pin # Description 1 Male inner pin contact 2 Female connector body (outer thread) Connector Specifications: l RP-SMA connector l Gender: Female Mating Connector Specifications: l RP-SMA connector l Gender: Male 7.3.7.
7 Main CPU Module interfaces BoltGATE 20-31 User's manual EN 7.3.8 MVB ESD+ ("RX only" or "RX/TX") interface specifications (vers: -11 only) 7.3.8.1 MVB ESD+ Connection Notes An ESD segment shall be terminated electrically at each end by a terminator. The terminator shall present an impedance of 120.0 Ω ± 2 % measured at 1.0 BR. Example of terminator (from the IEC 61375-1: 2007): The terminator shown in the following figure presents an impedance of 120.5 Ω and biases the line with about 0.786 V.
BoltGATE 20-31 User's manual EN 7.3.8.2 7 Main CPU Module interfaces MVB S1: connector specifications Connector Layout: 7.3.8.3 Connector Pinout: Signal Type Description 1 2 A.Data_P IO Line A Data+ A.Data_N IO Line A Data- 3 NC NC No Connection Connector Specifications: l Standard 9-Pin D-Sub (plug) l Gender: Male 4 B.Data_P IO Line B Data+ 5 B.Data_N IO Line B Data- 6 A.
7 Main CPU Module interfaces 7.
BoltGATE 20-31 User's manual EN 7.5 7 Main CPU Module interfaces Main CPU Module Service Panel and Service Interfaces The Service Panel A is placed on the front side of the Main CPU Module and protects the service interfaces: The Service Interfaces are as follows: Ref # Description A Reset Pushbutton B MicroSIM push-push receptacle (not available) C TTL Serial Console (3.
7 Main CPU Module interfaces 7.5.1 BoltGATE 20-31 User's manual EN How to insert a MicroSD card To insert a MicroSD card, complete the following steps: 1. Orient the MicroSD card as in the figure below, with the contacts facing the ETHx connectors 2. Push the MicroSD card in the receptacle to lock it. 7.5.2 TTL Serial Console connector specifications Connector Layout: Connector Specifications: l Shrouded header l Gender: Male l Type: Pitch 1.
BoltGATE 20-31 User's manual EN 8 8 BoltAIR 20-31 interfaces BOLTAIR 20-31 INTERFACES This chapter gives the following information: 8.1 BoltAIR 20-31 connectors 58 8.2 BoltAIR 20-31 LED indicators 66 8.3 BoltAIR 20-31 Service Panel and Service Interfaces 67 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
8 BoltAIR 20-31 interfaces 8.
BoltGATE 20-31 User's manual EN 8.1.
8 BoltAIR 20-31 interfaces 8.1.1.1 BoltGATE 20-31 User's manual EN A1: Main antenna connector specifications Connector Layout: Connector Pinout: Pin # Description 1 Female inner pin contact 2 Female connector body (outer thread) Connector Specifications: l SMA connector l Gender: Female Mating Connector Specifications: l SMA connector l Gender: Male 8.1.1.
BoltGATE 20-31 User's manual EN 8.1.2 8 BoltAIR 20-31 interfaces Wi-Fi and Bluetooth specifications NOTICE If the country code is in Europe, channels 12/13 of 2.4 GHz frequency are not available for station mode. Feature Description Frequency bands WLAN: l l l l l 2.4 GHz ISM Bands 2.412 - 2.472 GHz, 2.484 GHz 5.15 - 5.25 GHz (FCC UNII-low band) for US/Canada, Japan and Europe 5.25 - 5.35 GHz (FCC UNII-middle band) for US/Canada and Europe 5.47 - 5.725 GHz for Europe 5.725 - 5.
8 BoltAIR 20-31 interfaces BoltGATE 20-31 User's manual EN Feature Description RF receive Sensitivity (Typical) l l l l l 62 / 98 802.11a: 54M less than 68 dBm 802.11b: 11M less than 78 dBm 802.11g: 54M less than 68 dBm 802.11n 2.4G: o HT20 MCS7 less than 64 dBm o HT40 MCS7 less than 61 dBm 802.11n 5G: o HT20 MCS7 less than 64 dBm o HT40 MCS7 less than 61 dBm © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
BoltGATE 20-31 User's manual EN 8.1.2.1 8 BoltAIR 20-31 interfaces A4: Wi-Fi and Bluetooth co-existence main antenna connector specifications Connector Layout: Connector Pinout: Pin # Description 1 Male inner pin contact 2 Female connector body (outer thread) Connector Specifications: l RP-SMA connector l Gender: Female Mating Connector Specifications: l RP-SMA connector l Gender: Male 8.1.2.
8 BoltAIR 20-31 interfaces BoltGATE 20-31 User's manual EN 8.1.3 Odometer specifications 8.1.3.1 How the odometer input works The odometer input is a digital interface that counts the input pulses and detect with them the speed of a vehicle. The input, available on pins ODOM+ and ODOM-, is optically insulated and has a programmable threshold level.
BoltGATE 20-31 User's manual EN 8.1.4 8 BoltAIR 20-31 interfaces Earth connection terminal specifications Always use this terminal to connect the product to an earth point in the installation. Terminal Layout: Terminal Label: Terminal Parts: Part # Description 1 M4 stud bolt (length = 6.8 mm) 2 M4 lock nut 3 M4 washer NOTICE The earthing conductor to be connected to this terminal must have a size of 1 mm2.
8 BoltAIR 20-31 interfaces 8.2 BoltGATE 20-31 User's manual EN BoltAIR 20-31 LED indicators The BoltAIR 20-31 LED indicators A are as follows: 66 / 98 LED Colour Description U1 Green User programmable LED#1 S1 Green Mini PCI Express slot #1 activity S2 Green Mini PCI Express slot #2 activity S3 Green Mini PCI Express slot #3 activity PWR Blue Power input presence © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.
BoltGATE 20-31 User's manual EN 8.3 8 BoltAIR 20-31 interfaces BoltAIR 20-31 Service Panel and Service Interfaces The Service Panel A is placed on the front side of the BoltAIR 20-31 and protects the service interfaces: The Service Interfaces are as follows: Ref # Description A 1st MicroSIM push-push receptacle B 2nd MicroSIM push-push receptacle (not available) © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
8 BoltAIR 20-31 interfaces 8.3.1 BoltGATE 20-31 User's manual EN How to insert a MicroSIM card To insert a MicroSIM card, complete the following steps: 1. Orient the MicroSIM card as in the figure below, with the contacts facing the antenna connectors and the cut corner A facing the receptacle 2. Push the MicroSIM card in the receptacle to lock it. 68 / 98 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
BoltGATE 20-31 User's manual EN 9 9 BoltIO 20-31 interfaces BOLTIO 20-31 INTERFACES This chapter gives the following information: 9.1 BoltIO 20-31 connectors 70 9.2 BoltIO 20-31 LED indicator 74 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
9 BoltIO 20-31 interfaces 9.1 BoltGATE 20-31 User's manual EN BoltIO 20-31 connectors The BoltIO 20-31 connectors are as follows: Ref # Label Description A I/O 0 12x Digital Inputs B I/O 1 4x Digital Inputs + 4x Digital Outputs C I/O 2 12x Digital Outputs D 9.1.1 Earth connection terminal Digital inputs and digital outputs characteristics Digital I/Os Isolation: l Inputs 3.7kV l Outputs: 1.
BoltGATE 20-31 User's manual EN 9.1.2 Insulated Digital Inputs 9.1.2.1 Electrical specifications 9 BoltIO 20-31 interfaces The table below shows the electrical specifications of the digital inputs at 24 VDC of nominal supply voltage: 9.1.2.2 Characteristic Value @ 24 VDC Logic Zero 0 V ≤ VIN_low ≤ 1.
9 BoltIO 20-31 interfaces 9.1.3.3 BoltGATE 20-31 User's manual EN I/O 0: 12x Digital Inputs connector specifications Connector Layout: Connector Specifications: l Standard HD 15-Pin D-Sub (plug) l Gender: Male Mating Connector Specifications: l Standard HD 15-Pin D-Sub (socket) l Gender: Female 9.1.3.
BoltGATE 20-31 User's manual EN 9.1.3.5 9 BoltIO 20-31 interfaces I/O 2: 12x Digital Outputs Connector Layout: Connector Pinout: Connector Specifications: l Standard HD 15-Pin D-Sub (plug) l Gender: Male Mating Connector Specifications: l Standard HD 15-Pin D-Sub (socket) l Gender: Female 9.1.
9 BoltIO 20-31 interfaces 9.2 BoltGATE 20-31 User's manual EN BoltIO 20-31 LED indicator The BoltIO 20-31 LED indicator A is as follows: 74 / 98 LED Colour Description PWR Blue Power input presence © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
BoltGATE 20-31 User's manual EN 10 10 BoltSER 20-31 interfaces BOLTSER 20-31 INTERFACES This chapter gives the following information: 10.1 BoltSER 20-31 connectors 76 10.2 BoltSER 20-31 LED indicator 79 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
10 BoltSER 20-31 interfaces 10.1 BoltGATE 20-31 User's manual EN BoltSER 20-31 connectors The BoltSER 20-31 connectors are as follows: Ref # Label Description A COM 0 1x RS-232/422/485 serial port B COM 1 1x RS-232/422/485 serial port C CAN 1x isolated (5kV) CAN FD port D 10.1.1 Earth connection terminal Serial Ports characteristics l l 10.1.2 CAN Port characteristics l l l l 76 / 98 Isolation: 3.
BoltGATE 20-31 User's manual EN 10.1.2.1 COM 0: 1x RS-232/422/485 connector specifications Connector Layout: Connector Specifications: l Standard 9-Pin D-Sub (plug) l Gender: Male Mating Connector Specifications: l Standard 9-Pin D-Sub (socket) l Gender: Female 10.1.2.
10 BoltSER 20-31 interfaces 10.1.3 BoltGATE 20-31 User's manual EN Earth connection terminal specifications Always use this terminal to connect the product to an earth point in the installation. Terminal Layout: Terminal Label: Terminal Parts: Part # Description 1 M4 stud bolt (length = 6.8 mm) 2 M4 lock nut 3 M4 washer NOTICE The earthing conductor to be connected to this terminal must have a size of 1 mm2.
BoltGATE 20-31 User's manual EN 10.2 10 BoltSER 20-31 interfaces BoltSER 20-31 LED indicator The BoltSER 20-31 LED indicator A is as follows: LED Colour Description PWR Blue Power input presence © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
(This page is intentionally left blank)
BoltGATE 20-31 User's manual EN 11 11 Product installation and power supply PRODUCT INSTALLATION AND POWER SUPPLY This chapter gives the following information: 11.1 Introduction 82 11.2 How to install the product on a DIN Rail 83 11.3 How to remove the product from a DIN Rail 83 11.4 Mechanical specifications 84 11.5 How to supply power to the system 86 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
11 Product installation and power supply 11.1 BoltGATE 20-31 User's manual EN Introduction The product is intended for professional use and must be installed by qualified personnel only. The product must be installed in a secured location, accessible to authorized personnel only (for example in a cabinet / technical compartment). The product includes a Mounting bracket A located on its rear side.
BoltGATE 20-31 User's manual EN 11.2 11 Product installation and power supply How to install the product on a DIN Rail Prerequisite: Make sure that the DIN rail is placed horizontally. To install the product on a DIN rail, complete the following steps: 1. Position the product so that the upper side of the Mounting bracket hooks on the upper edge of the DIN rail, see step 1 2.
11 Product installation and power supply 11.4 Mechanical specifications 11.4.1 Main CPU Module mechanical dimensions BoltGATE 20-31 User's manual EN The mechanical dimensions are as follows (the image shows the Boltage 20-31-11 as an exemple): 61x132x150 (WxHxD); mm - Connectors and Mounting Bracket excluded 11.4.
BoltGATE 20-31 User's manual EN 11.4.3 11 Product installation and power supply BoltIO 20-31 mechanical dimensions The mechanical dimensions are as follows: 42x132x150 (WxHxD); mm - Connectors and Mounting Bracket excluded 11.4.4 BoltSER 20-31 mechanical dimensions The mechanical dimensions are as follows: 42x132x150 (WxHxD); mm - Connectors and Mounting Bracket excluded © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
11 Product installation and power supply 11.5 BoltGATE 20-31 User's manual EN How to supply power to the system The Main CPU Module and the Expansion Modules are not provided with any ON/OFF switch. The Power IN connector on the Main CPU Module is the disconnecting means from the power supply network. All Expansion Modules are intended to work only if connected to the Main CPU Module. 11.5.1 11.5.2 Power supply specifications Power Supply BoltGATE 20-31: Ultra-wide input voltage range: 9 to 137.
BoltGATE 20-31 User's manual EN 11.5.3 11 Product installation and power supply Main CPU Module and Expansion Modules electrical interconnections The electrical interconnections between the Main CPU Module and the Expansion Modules is made using high speed card edge connectors, coupled using a PCB.
11 Product installation and power supply 11.5.4 BoltGATE 20-31 User's manual EN Power supply safety instructions WARNING Risk of electric shock. Failure to supply power correctly could result in death or serious injury, and could damage the equipment or other property. Refer to "What to do before you supply power to the product" below. 11.5.4.
BoltGATE 20-31 User's manual EN 11 Product installation and power supply 3. Make sure that the DC power source is turned OFF 4. Setup an external fuse on the line coming from the negative terminal of the DC power source 5. Turn ON the DC power source. The system remains OFF 6. Connect the Earth connection terminal (Ref# E in the table below) to an earth point in the installation 7.
11 Product installation and power supply 11.5.6 BoltGATE 20-31 User's manual EN How to turn OFF the system There are two ways to turn OFF the system: l By executing the poweroff Linux command l By turning OFF the Ignition Key To turn OFF the system by executing the poweroff command, complete the following steps: 1. Login the Administration Console 2. Execute the poweroff command. The system turns OFF (only if the ignition key is OFF otherwise it reboots.
BoltGATE 20-31 User's manual EN 12 12 Eurotech Everyware IoT EUROTECH EVERYWARE IOT This chapter gives the following information: 12.1 Everyware IoT 92 12.2 Everyware Software Framework (ESF) 92 12.3 The ESF Web UI 92 12.4 The ESF Wires application 93 12.5 Everyware Cloud (EC) 94 12.6 For more information 94 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
12 Eurotech Everyware IoT 12.1 BoltGATE 20-31 User's manual EN Everyware IoT Everyware IoT is an IoT platform providing hardware and software building blocks with an open, integrated and managed core to allow flexibility and interoperability across different vendors, to reduce time to market and for seamless integration between OT (operational technology) domain and IT (information technology) domain. 12.
BoltGATE 20-31 User's manual EN 12.4 12 Eurotech Everyware IoT The ESF Wires application ESF gives also a dataflow programming model: Wires. Wires simplifies the development of Edge Computing Applications leveraging reusable configurable components. In the dataflow programming model, the application logic is expressed as a directed graph (flow) where each node can have inputs, outputs and independent processing units.
12 Eurotech Everyware IoT 12.5 BoltGATE 20-31 User's manual EN Everyware Cloud (EC) Everyware Cloud (EC) is the IoT Integration Platform distributed and supported by Eurotech. It gives all the services required for the management of IoT gateways and devices in the field, including configuration management, application life-cycle management and remote access. It also connects the data collected by field-deployed devices to enterprise applications and analytics leveraging reliable and open protocols. 12.
BoltGATE 20-31 User's manual EN 13 13 Product maintenance PRODUCT MAINTENANCE This chapter gives the following information: 13.1 How to maintain the product 96 13.2 How to safely remove the power supply 96 13.3 How to verify the installation of the product 96 13.4 How to clean the product 96 © 2022 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy Code: BTGATE-20-31_MAN_EN_1-6 Revision: 1-6 2022.07.
13 Product maintenance 13.1 BoltGATE 20-31 User's manual EN How to maintain the product Periodically inspect the product to verify its integrity and to ensure proper operation. To maintain the product, complete this procedure: 1. Carefully read and understand the instructions contained in the section "Safety-related information" on page 9 2. Safely remove the power supply. For more information, refer to: "How to safely remove the power supply" below 3. Verify the installation of the product.
BoltGATE 20-31 User manual Rev.
EUROTECH.COM HEADQUARTERS Via Fratelli Solari, 3/a 33020 Amaro (UD) - Italy Tel: +39 0433.485.411 Fax: +39 0433.485.499 Email: welcome@eurotech.com Web: https://www.eurotech.com For your Eurotech local contact refer to: eurotech.com/contacts For the Eurotech Global Support Centre refer to: support.eurotech.com For the Eurotech Download Area refer to: eurotech.
