BEDIENUNGSANLEITUNG USER MANUAL LED KLS-150 COMPACT LIGHT SET Für weiteren Gebrauch aufbewahren! Keep this manual for future needs! © Copyright Nachdruck verboten! Reproduction prohibited!
Inhaltsverzeichnis/Table of contents 1. EINFÜHRUNG ................................................................................................................................................................ 3 2. SICHERHEITSHINWEISE .............................................................................................................................................. 3 3. BESTIMMUNGSGEMÄSSE VERWENDUNG ................................................................................................
BEDIENUNGSANLEITUNG LED KLS-150 Kompakt-Lichtset Lesen Sie vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung, Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen - entsprechend qualifiziert sein - diese Bedienungsanleitung genau beachten - die Bedienungsanleitung als Teil des Produkts betrachten - die Bedienungsanleitung während der Lebensdauer des Produkts behalten - die Bedienungsa
Bitte überprüfen Sie vor der ersten Inbetriebnahme, ob kein offensichtlicher Transportschaden vorliegt. Sollten Sie Schäden an der Netzleitung oder am Gehäuse entdecken, nehmen Sie das Gerät nicht in Betrieb und setzen sich bitte mit Ihrem Fachhändler in Verbindung. Der Aufbau entspricht der Schutzklasse I. Der Netzstecker darf nur an eine Schutzkontakt-Steckdose angeschlossen werden, deren Spannung und Frequenz mit dem Typenschild des Gerätes genau übereinstimmt.
3. BESTIMMUNGSGEMÄSSE VERWENDUNG Das Kompakt-Lichtset LED KLS-150 besteht aus vier superflachen LED-Scheinwerfern mit Querträger und dem passenden Fußschalter FP-2 zur Steuerung. Das Set lässt sich im Automatikbetrieb oder im musikgesteuerten Modus betreiben. Zusätzlich ist eine Blackout-Funktion wählbar. Die Lieferung erfolgt vormontiert in einer praktischen Transporttasche. Das Set kann auf ein Leuchten-Stativ aufgesetzt oder an einer Traverse befestigt werden.
Beachten Sie bitte, dass eigenmächtige Veränderungen an dem Gerät aus Sicherheitsgründen verboten sind. Der Serienbarcode darf niemals vom Gerät entfernt werden, da ansonsten der Garantieanspruch erlischt. Wird das Gerät anders verwendet als in dieser Bedienungsanleitung beschrieben, kann dies zu Schäden am Produkt führen und der Garantieanspruch erlischt. Außerdem ist jede andere Verwendung mit Gefahren, wie z. B. Kurzschluss, Brand, elektrischem Schlag, Abstürzen etc. verbunden. 4. GERÄTEBESCHREIBUNG 4.
4.
5. INSTALLATION 5.1 Montage auf einem Stativ Für den mobilen Einsatz setzen Sie das Lichtset auf ein Leuchten-Stativ auf. Passende Artikel finden Sie im Kapitel Zubehör. 1. Lösen Sie zunächst am Stativ die Feststellschrauben der Stellfüße. Ziehen Sie die Stellfüße aus, bis die Querstreben in einem 90°-Winkel zu den Stellfüßen stehen. Ziehen Sie die Feststellschrauben der Stellfüße fest. 2. Setzen Sie das Lichtset über seinen Stativzapfen am oberen Stativende auf und ziehen Sie die Feststellschraube fest. 3.
Während des Auf-, Um- und Abbaus ist der unnötige Aufenthalt im Bereich von Bewegungsflächen, auf Beleuchterbrücken, unter hochgelegenen Arbeitsplätzen sowie an sonstigen Gefahrbereichen verboten. Der Unternehmer hat dafür zu sorgen, dass sicherheitstechnische und maschinentechnische Einrichtungen vor der ersten Inbetriebnahme und nach wesentlichen Änderungen vor der Wiederinbetriebnahme durch Sachverständige geprüft werden.
6. INBETRIEBNAHME 1. Verbinden Sie den Anschlussstecker des Fußschalters mit der Buchse FOOT PEDAL am Lichtset. 2. Schließen Sie das Lichtset über das Netzkabel ans Netz an (230 V AC, 50 Hz ~). Das Lichtset ist damit eingeschaltet.
7. BEDIENUNG Das Lichtset lässt sich mit dem beiliegenden Fußschalter FP-2 bequem bedienen. Der Fußschalter ermöglicht das schnelle Einstellen des Automatikbetriebs, der Musiksteuerung oder der Blackout-Funktion. Nach dem Anschluss ans Netz ist das Gerät betriebsbereit und die Musiksteuerung ist aktiviert. 7.1 Automatikbetrieb 1. Im Automatikbetrieb stehen sieben voreingestellten Farben sowie prozessorgesteuerte Farbwechsel bzw. Farbüberblendungen zur Verfügung.
8. REINIGUNG UND WARTUNG Der Unternehmer hat dafür zu sorgen, dass sicherheitstechnische und maschinentechnische Einrichtungen mindestens alle vier Jahre durch einen Sachverständigen im Umfang der Abnahmeprüfung geprüft werden. Der Unternehmer hat dafür zu sorgen, dass sicherheitstechnische und maschinentechnische Einrichtungen mindestens einmal jährlich durch einen Sachkundigen geprüft werden.
9. TECHNISCHE DATEN Spannungsversorgung: Gesamtanschlusswert: Anzahl der LEDs: LED-Typ: Abstrahlwinkel: Musiksteuerung: TV-Zapfen: Maximale Umgebungstemperatur Ta: Max. Leuchtentemperatur im Beharrungszustand TB: Mindestabstand zu entflammbaren Oberflächen: Mindestabstand zum angestrahlten Objekt: Maße (LxBxH): Gewicht: 230 V AC, 50 Hz ~ 60 W 162 3-W-TCL 140° über eingebautes Mikrofon Ø 28 mm 45° C 60° C 0,50 m 0,10 m 950 x 45 x 230 mm 6 kg 9.
USER MANUAL LED KLS-150 Compact Light Set CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! For your own safety, please read this user manual carefully before you initially start-up.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer. This device falls under protection-class I. The power plug must only be plugged into a protection class I outlet. The voltage and frequency must exactly be the same as stated on the device.
3. OPERATING DETERMINATIONS The compact light set LED KLS-150 consists of four slimline LED spots on a crossbar. Control is possible via the included foot pedal FP-2. The light set can be used in automatic oder sound-controlled mode. Additonally, a blackout function is available. The set comes pre-assembled in a pratical transport bag. It can be placed on a lighting stand or mounted to a truss.
If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc. 4. DISCRIPTION 4.
4.2 Operating elements and connections 1 Fastening screws 7 Fixation screws 2 Sensitivity control for the microphone 8 LED spot 1 to 4 3 Microphone for sound-controlled operation 9 Connectors for the LED spots 4 Speed selector switch for automatic mode 10 Power cable 5 Connector for the foot pedal FP-2 11 TV pin for placing on a stand 6 Fuse holder 12 Pedal PRESETS for automatic mode 13 Pedal BLACKOUT for switching off the LEDs For sound control, press down both pedals simultaneously.
5. MOUNTING 5.1 Mounting on a stand For mobile use place the light set on a lighting stand. Suitable items can be found in chapter Accessories. 1. On the stand, loosen the fixation screws of the legs. Pull out the legs until the cross struts stand at a 90° angle to the legs. Tighten the fixation screws of the legs. 2. Attach the light set via its TV pin on the control unit to the top end of the stand and fasten the fixation screw. 3. Caution! The load has to be installed in a balanced way.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year. Before lifting or lowering the telescopic tubes, you must always block a safety area around the stand. This safety area must have a diameter of 1.5 times the maximum height.
7. OPERATION The included foot pedal FP-2 allows convenient control of the light set. It provides quick access to the automatic mode, sound control or the blackout function. After connecting the light set to the mains it is ready for operation. As a basic setting, sound control is activated. 7.1 Automatic mode 1. In automatic mode, one in seven preset colors or color change and color fade of the colors can be selected. Press down the left pedal PRESETS repeatedly for the desired function.
8. CLEANING AND MAINTENANCE The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year.
9. TECHNICAL SPECIFICATIONS Power supply: Power consumption: Number of LEDs: Type of LEDs: Beam angle: TV spigot: Sound control: Maximum ambient temperature Ta: Maximum housing temperature TB (steady state): Min. distance from flammable surfaces: Min. distance to lighted object: Dimensions (LxWxH): Weight: 230 V AC, 50 Hz ~ 60 W 16 3 W TCL 140° Ø 28 mm via built-in microphone 45° C 60° C 0.50 m 0.10 m 950 x 45 x 230 mm 6 kg 9.