cooking USAGE AND CARE GUIDE PRODUCT CODE: ECT600GS ECT60WCX ECT60GX ECT900GX
This manual explains the proper installation and use of your appliance, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. In case of failure, only the Authorized Technical Service may repair this hob. Otherwise the guarantee will be null and void. Warning General Safety ⚫ The appliance may only be installed and connected by licensed gasfitters / authorized ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ persons.
Children’s Safety ⚫ ⚫ ⚫ The cooking zones will become hot when you cook. Therefore, always keep small children away from the appliance. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. Safety During Use ⚫ There is the risk of burns from the appliance if used carelessly. ⚫ Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
AS/NZS 3000 – Electrical Installations (Wiring Rules) ⚫ ⚫ ⚫ ⚫ Building codes Any other relevant statutory regulations. Check the gas type label on the underside of the hotplate, adjacent to the gas connection to ensure it corresponds to the installation gas supply. If in doubt contact the supply authority. The power supply cord (supplied) must not touch against any hot surfaces and must be placed so that its temperature does not exceed 75 degrees at any point along its length.
Product Description Burner ECT600GS Pan support Panel knobs No Model Burner* FSD . 1 ECT600GS 1W+2SR+1A With Pan Knob Total gas supports position consuption Enamel Front LPG: Over view 27.5MJ/h NG: 26.0MJ/h 2 ECT60WCX 1W+2SR+1A With Cast iron Front LPG: 30.5MJ/h NG: 29.5MJ/h 3 ECT60GS 1R+2SR+1A With Cast iron Right LPG: 30.5MJ/h NG: 29.5MJ/h 4 ECT900GX 1W+1R +2SR+1A With Cast iron Front LPG: 39.6MJ/h NG: 39.
Accessory Picture Quantity Name ( for reference only, physical unit maybe different) User Manual 1 Sealing tape 1 roll Additional labels You have additional rating label in accessory bag, suggest attach it onto a surface where it can be read e.g. inside 1 set surface of adjacent cupboard Installation 4 sets clip Screws 4 pcs ST4.
Installation Before Installation: ⚫ Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent surfaces and overhead surfaces required by the relevant gas appliance installation code (see above) will comply. Dimensions are specified in millimeters (mm) Overhead cupboards and range hood = 650 mm. Side and rear clearance = 200 mm to any burner edge. Overhead exhaust/ceiling fan = 750 mm Horizontal surfaces adjacent the hob = less than or equal to the hob height.
2. Place Burner Box Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite. Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench. 3. Fit Burners And Trivet. Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). The ignitor (S) must be clean for trouble free sparking.
After having installed the hotplate, the GPO must always be in an accessible position. ECT60WCX , ECT600GS, ECT60GX ECT900GX Wiring diagram 4. Gas Connection Install in accordance with relevant gas standards and/or codes of practice applicable. Connect the elbow fitting to the appliance gas manifold connection, and check that seals between the elbow and manifold connection are in place and in good condition.
9
ADJUSTING THE BURNER MINIMUM FLAME HEIGHT: NOTE: This adjustment can only be performed by the installer or an authorised service personnel. The minimum burner flame is factory adjusted for the gas type stated on the gas type label adjacent to the gas connection and should not require adjustment. Adjustment may be required if the hotplate has been converted from Natural gas to Universal LPG or vice versa.
Start Using Your Appliance ECT60WCX，ECT600GS， ECT60GX ECT900GX Description Explanation These show which zone is under control. Zone indicators Flame power Flame power of the zones, is the lowest and is the highest. The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power supply (i.e. nominal 220~240 V ac) to operate. If power is not available, the hotplate will still work but the burners will have to be lit with a match or similar.
Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit, while at the same time depressing the gas control knob to activate the spark ignition. Once the burner is alight continue to depress the gas control knob for 5 – 10 seconds to allow the flame safeguard to activate.
Maintenance & Troubleshooting Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces. STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. weekly) to ensure long life expectancy of the hotplate. Ensure hotplate has cooled. Wash down with warm soapy water and rinse with clean water. Dry with a clean soft cloth.
TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative, and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. DO NOT MODIFY THIS APPLIANCE. It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by warranty. Abnormal conditions include: ⚫ Excessively yellow or sooting flame type. ⚫ Flame lifting off the burner ports.
www.euroappliances.com.au HEAD OFFICE 65 Glynburn Road, Glyne SA 5070 Ph: 08 8165 1012 Pronto Service + Support: 1800 440 335 Email: service@eurostylegroup.com.
