QUICK START GUIDE Video Doorbell 2K (Battery-Powered) Set
TABLE OF CONTENTS What’s Included 02 13 Mounting The Bracket Product Overview 04 16 Mounting The Doorbell How The System Works 06 17 Detaching The Doorbell Connecting The Homebase 07 18 Recharging The Doorbell Setting Up The System 08 19 Powering The Doorbell With Existing Doorbell Wires Determining The Power Option 09 27 Notice Finding A Mounting Spot 11 30 Customer Service English 01
WHAT’S INCLUDED For Video Doorbell Installation Video Doorbell 2K (Battery-Powered) Mounting Bracket Screw Hole Positioning Card 15° Mounting Wedge (Optional) Model: T8210 FCC ID: 2AOKB-T8210 IC: 23451-T8210 Jumper for Original Chime (Optional) Extension Wires and Wire Nuts (Optional) QSG Screw Packs (Spare screws and anchors are included) 02 English Quick Start Guide USB Charging Cable Doorbell Detaching Pin
For HomeBase 2 Installation Model: HomeBase 2 Power Adapter for HomeBase 2 Ethernet Cable for HomeBase 2 FCC ID: 2AOKB-T8010 IC: 23451-T8010 Note: Power plug may vary in different regions.
PRODUCT OVERVIEW Video Doorbell (Battery Powered) Front view: 1 2 1. Motion Sensor 3 2. Microphone 4 3. Camera Lens 4. Ambient Light Sensor 5 5. LED Ring 6. Doorbell Button 6 7. Speaker 7 Rear View: 1 2 3 1. Micro USB Charging Port 2. SYNC/RESET Button 3. Power Terminals for Existing Doorbell Wire (Optional) 4.
Video Doorbell (Battery Powered) 1 2 7 3 4 5 6 1. Status LED 5. Ethernet port 2. Speaker 6. SYNC/ALARM OFF button 3. Power port 7. Reset button 4.
HOW THE SYSTEM WORKS How the System Works The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is the HomeBase in your house. The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere.The HomeBase stores video clips on its built-in storage.
STEP 1 CONNECTING THE HOMEBASE Connect the HomeBase 2 to the Internet 1. Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router. 2. The LED indicator turns blue (this may take up to 1min) when HomeBase 2 is ready for setup.
STEP 2 SETTING UP THE SYSTEM Download the App and Set up the System Download the Eufy Security app from the App Store (iOS devices) or Google Play (Android devices). Sign up for a Eufy Security account, then follow the onscreen instructions to complete the setup.
STEP 3 DETERMINING THE POWER OPTION Option 1 - Battery Powered 1. If you don’t have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick. 2. When the doorbell battery level is low, you need to detach and charge it. 3. If you choose this option, please jump to STEP 4 FINDING A MOUNTING SPOT. 6 months Note: The battery life varies depending on usage.
Option 2 - Doorbell Wire Powered 1. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don’t need to detach and charge it after installation. 2. Since the doorbell is connected to the wires, the mounting position is limited. 3. If you choose this option, please jump to Appendix 3 Powering the Doorbell with Doorbell Wires.
STEP 4 FINDING A MOUNTING SPOT Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the WEQI XMQI *MRH E PSGEXMSR [LIVI ]SY GER KIX XLI HIWMVIH ½IPH SJ ZMI[ Consider the below factors: 1. Check if you can reuse the existing holes and anchors on the wall or door frame. 2. If you want to place the doorbell close to a side wall, make sure the wall doesn’t WLS[ YT MR XLI ½IPH SJ ZMI[ 3XLIV[MWI -6 PMKLX [MPP FI VI¾IGXIH ERH RMKLX ZMWMSR will become blurry. 3.
Place the Screw Hole Positioning Card against the wall to mark the position.
STEP 5 MOUNTING THE BRACKET Mount the Doorbell on a Wooden Surface If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall, The Screw Hole Positioning Card indicates the position of the screw holes.
Mount the Doorbell on Surfaces Made Out of Hard Materials 1. If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64”(6mm) drill bit. 2. Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall.
Wall Mounting Bracket Without 15° Mounting Wedge 2 Wall Mounting Wedge Mounting Bracket With 15° Mounting Wedge 2 English 15
STEP 6 MOUNTING THE DOORBELL Mount the Doorbell Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place. You’re all set! If you want to detach the doorbell or recharge it, please refer to the following sections.
APPENDIX 1 DETACHING THE DOORBELL Detach the Doorbell 1. Use the doorbell detaching pin provided if you wish to detach the doorbell from the Mounting Bracket. 2. Press and hold the hole on the bottom of the doorbell and then lift its bottom to take it off.
APPENDIX 2 RECHARGING THE DOORBELL Recharge the Doorbell LED indication Charging time 18 English Charging: Solid orange Fully charged: Solid cyan 6 hours from 0% to 100%
APPENDIX 3 POWERING THE DOORBELL WITH EXISTING DOORBELL WIRES 3.1 Verify whether the doorbell wires are working 1. Ring the existing doorbell to check if it is working. If the doorbell doesn’t ring, your doorbell wires may be defective. Power the doorbell on its own battery or GSRWYPX ER IPIGXVMGMER XS ½\ XLI [MVIW 2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off. OFF OFF Always be careful when handling wires.
What is required: Philips-Head Screwdriver Phillips-Head Screwdriver (User provides it.) 3.3 Find a Mounting Spot 1. Determine the mounting position of the doorbell. Consider the below factors: ① Check if you can reuse the existing holes and anchors on the wall or door frame. ② If you are drilling the mounting holes for the first time, the recommended mounting height is 48" / 1.2 m from the ground.
15° 1.76m(5’9”) 1.2m (48") 1m (40") 0.3m (12") Door Video Doorbell Without 15° Mounting wedge Door Video Doorbell With 15° Mounting wedge 2. Place the Screw Hole Positioning Card against the wall to mark the position.
3.4 Mount the Bracket If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs Phillips-Head Screwdriver (User provides it.
If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco: ① Drill 2 holes through the Screw Hole Positioning Card with 15/64”(6mm) drill bit. ② Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall.
Wall Mounting Bracket Without 15° Mounting Wedge 2 24 English Wall Mounting Wedge Mounting Bracket With 15° Mounting Wedge 2
3.5 Connect the Doorbell Wires to the Doorbell Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal. What is required: Wires and Wire Nuts (Optional), Video Doorbell, Philips-head Screwdriver Extension Wires and Wire Nuts (Optional) Video Doorbell 2K (Wired) Model: T8210 Phillips-Head Screwdriver (User provides it.
3.6 Mount the Doorbell on the Bracket Align the doorbell on top and then snap it on the bottom. 3.7 Restore Power Switch the master circuit breaker back to ON. ON ON You’re all set! If you want to detach the doorbell or recharge it, please refer to the corresponding sections.
NOTICE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: 'LERKIW SV QSHM½GEXMSRW RSX I\TVIWWP] ETTVSZIH F] XLI TEVX] VIWTSRWMFPI for compliance could void the user's authority to operate the equipment.
This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of conformity, visit the Web site:https://www.eufylife.com/. This product can be used across EU member states.
This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment.
CUSTOMER SERVICE • Warranty 12-month limited warranty • Call Us United States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT) United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT) Germany +49 (0) 69 9579 7960 Mo-Fr 6:00-11:00 • Email Us Customer Support: support@eufylife.
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.