User Manual Keypad 1 4 7 X Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.
TABLE OF CONTENTS What’s Included 02 14 OTA Update Product Overview 03 15 Resetting Your Keypad Mounting Your Keypad 05 15 Specification Using the Keypad 09 15 Troubleshooting Operating on the eufy Security App 13 16 Notice Charging Your Keypad 14 19 Customer Service English 01
WHAT’S INCLUDED PRODUCT OVERVIEW For Keypad Installation Keypad 1 2 3 1 1 4 7 X 2 4 2 5 8 5 7 3 X6 8 6 9 0 9 0 4 9 3 1 QSG CUS 8 QSG CUS OFF Keypad T8960 4 User Manual OFF 7 X 2 5 8 0 5 3 6 9 CUS OFF Mounting Screws User Manual 6 7 ① Panic Button • Press and hold for 3 seconds to trigger the alarm ② SYNC Button • Press and hold for 2 seconds to pair with HomeBase Charging Cable 3M Adhesive Sticker * 2 Welcome Card ③ Reset ④ LED Indicator ⑤ Buzzer ⑥ Power Indicator
Adding the Keypad to the System Note: • • Make sure you’ve first completed the setup of your eufy Security HomeBase.
Make sure the keypad is fully charged. A fully-charged keypad’s battery can last for 6 months per charge.
1. Go to Add Device, and then select Keypad to add it to your system.
2. Stick the keypad onto the wall. 2. Place the mounting plate against the wall, matching UP and Down as indicated on the back of the mounting bracket. Push a pencil tip through the holes on the mounting bracket to mark the location for mounting the keypad. 1 2 4 7 X 5 8 0 3 6 9 CUS OFF Option 2: Use the mounting screws 1. Slide the mounting bracket off. 06 English 3. Drill holes with a drill bit (15/64” / 6 mm) at each marking.
4. Insert anchors into the holes, and fix the mounting bracket onto the wall with the provided screws. No anchors are needed on wooden walls. USING THE KEYPAD Keypad Mode Introduction The Keypad features four modes: Away, Home, Customized and Disarmed, which are associated with four Keypad buttons respectively. Press to activate Away mode Press to activate Home mode Press to activate Customized mode Press to disarm the system 5. Slide the keypad down until it snaps perfectly onto the mounting bracket.
Set Customized Security Mode To set a customized security mode using the eufy Security app: Device Bypass Device bypass means that the system will ignore faulty sensors for a specific time while the system is armed. 1. Open the Keypad homepage. 2. Tap the “Security” tab. 3. Tap the “Modes” tab and then tap “Customize” to add your personalized settings. 4. Follow the on-screen instructions to define the actions of sensors. When the customized mode is activated, the sensors will act as defined in the app.
LED Indication LED indicator Numeric keypad area Mode button ( / ) / OPERATING ON THE EUFY SECURITY APP Status Description Keypad indicator blinks white 3 times Access code error All operations, such as mode switch, alarm on / off, device bypass, OTA update can be performed on the eufy Security app.
CHARGING YOUR KEYPAD RESETTING YOUR KEYPAD Before charging your keypad, check whether the Keypad power is low. When a keypad malfunction occurs, use a sharp-pointed object (such as SIM card opener) to reset the keypad. When the Keypad power is low: The Keypad’s LED indicator will flash red for 5 seconds when movement is detected nearby. On the eufy Security app, the Keypad power level icon will turn red. To charge your Keypad, use the micro USB cable and charger (not provided).
NOTICE This product complies with the radio interference requirements of the European Community. FCC Statement Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.