FCC ID:2AOKB-T8321M IC:23451-T8321M Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.
TABLE OF CONTENTS What’s in the Box 02 09 Mounting the Baby Camera on the Wall Feature Introduction 03 12 Monitor Menu Settings Setting Up the Camera and Monitor 05 15 Notice Adding a New Baby Camera to the Baby Monitor 07 19 Customer Service Using the Baby Monitor 08 English 01
WHAT’S IN THE BOX FEATURE INTRODUCTION Monitor Features 1 Video Baby Monitor 720P Video Baby Monitor 720P Model: T8321-M Model: T8321-C FCC ID:2AOKB-T8321C FCC ID:2AOKB-T8321M IC:23451-T8321M IC:23451-T8321C Monitor Micro-USB Power Cable (1 m) Camera MicroUSB Power Cable (3 m) 3 4 Wall Mount 5 Camera Adapter (5V 1A) Welcome Card User Manual 13 1 Screen 2 Menu button 3 Navigation button 4 OK button 7 Micro USB charging port Press to confirm the selection • Press to switch camera display
SETTING UP THE CAMERA AND MONITOR Camera Features Charge the Monitor 1 7 2 6 3 Fully charge the monitor before use. To charge: 5 1. Connect one end of the micro USB cable to the baby monitor, and the other end to the power adapter (5V/2A). 2. Plug the adapter into a power outlet. 3. Press and hold the power button for 2 seconds to turn the baby monitor on.
Charge the Camera 1. Connect one end of the micro USB cable to the baby camera, and the other end to the power adapter (5V 1A). 2. Plug the power adapter into a power outlet. ADDING A NEW BABY CAMERA TO THE BABY MONITOR The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the following steps when adding extra baby cameras or after resetting a baby camera. 1.
To check whether it is the latest version: 1 Visit the website below: https://www.eufylife.com/support/5505/spaceview-baby-monitor 2 If the firmware version is lower than the version shown online (highlighted in green), click the firmware version to download. The downloaded file includes firmware for both T8300 and T8321 models, make sure you use the T8321 firmware. 3 Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware Upgrade Manual to complete firmware upgrade.
3. Insert the screws through the mounting holes of the wall mount and screw into the anchors. 5. To get the optimal viewing angle, rotate the camera (25°upwards, 60° 72 and °F tilt functions are not backwards, 250° horizontally) manually, as pan supported on this model when using the navigation button. 60° 250° UP 4. 25° Snap the baby camera onto the wall mount.
MONITOR MENU SETTINGS Press and hold the power button to power on the monitor. Press the menu button to open Menu Settings. Menu Settings Menu Options Set the brightness of the screen. Sleep Mode Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off. Sound Alert You can set the baby monitor to alert you when a specific noise level is detected. Note: Surrounding noise might set off false alarm. Lullaby Select your desired lullaby song.
On-screen Menu Icons Icon Icon Description Wireless signal strength Night Vision Mode is enabled 1 Shows the camera that is currently presenting on the baby monitor screen Note: This icon will not appear on the screen when there is only one camera connected to the monitor.
The charger output voltage/current is 5Vdc/1A(for T8321-C) and 5Vdc/2A (for T8321-M).The plug considered as disconnect device of adapter. If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc / 1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
separation distance is 20cm. This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. RF Exposure Information (SAR) The Extremity SAR limit of FCC for Hand held is 4.0W/kg. Device is recommended to use in hand held only and SAR when hand held is 1.804 W/kg Worn on body will have unexpected RF exposure RISK.