Combo Scanner II Combo Scanner II‐5M‐3.
Version 1.
Index I. Unpack Combo Scanner II…………………................................2 II. Install film into the film holder…………..……………………........3 III. Quick Start.........................................................................6 IV. Operation Guide..............................................................14 V. Specification....................................................................
I. Unpack Combo Scanner II Slide Film Holder Backlight Holder Business Card Fixture Combo Scanner II Negative Film Holder USB/Video Cable Power Core & Cable Photo/Business Card Holder Clean Brush User Manual Note We strongly suggest using a clean, dry, non-alcohol cotton swab to clean the glass surface on the back-light holder and the business card fixture periodically to produce a clear image.
II. Install film into the film holder ● Install slide film into the holder entitled “Slides Only” 1. Open the slide holder as illustrated 2. Place slide in recessed slot in holder ● 3. Close the slide holder Install Negative Film into holder entitled “Negative Film Only” 1. Open the film holder as illustrated 2. Install film into negative film slot 3.
Note To avoid mirror image, follow the serial numbers (from left to right) on top of film when install negative film into holder Figure 2.1 If the image is upside down [Figure 2.2], the image can be corrected by pressing Down/Flip button before capturing [Figure 2.3]. Alternative, enter the playback mode and press Mode button to select Flip function [Figure 2.4] Figure 2.
Down/Flip button (Flip hard key) Flip ● Press hard key on top of device in live view [Figure 2.3] Playback button ● Press Playback button Mode/Setting to select Flip function (Refer to P.25) [Figure 2.
III.
How to use Combo Scanner II Scanning Film/Slide 1. Put Film into Film holder, and Insert the film holder into the right side of the unit. 2. Insert the back light holder at the rear side of the unit. 3. Plug in power cable to the power port on the unit and one end to the power outlet (Figure 3.1). Figure 3.
4. Press Power button to power on the unit. Enter media type menu to select the correct media for scanning. (Refer to P.29) Power button Media Type 5. Press OK/Capture button to capture the image. OK/Capture button 6. Press on Playback button to playback the saved images.
7. After capturing, take out the SD card which stored the saved images. 8. Alternative to 7, saved picture can be read directly, without taking out the SD card, from PC by entering MSDC mode. (Refer to P.
Scanning Photo 1. Remove the film/slide holder as well as the back light holder from the unit if either one is attached. Remove backlight holder by pressing down the handle and pull it out. Remove film/slide holder by exiting the sliding to the left hand side. 2. Open the photo holder frame as illustrated, place the photo on the base of the photo holder and close the photo holder frame.
3. Insert the photo holder into the photo slot of the unit. 4. Enter Media Type Mode to select the correct media for scanning. (Refer to P.29) Media Type 5. Press OK/Capture button to capture the image.
Scanning Business Card 1. Follow step 1 from scanning photo to remove the film/slide holder as well as the back light holder in the previous pages. 2. Open the photo holder frame and place the business card on the base of the photo holder following the engraved guide line. 3. Put the business card fixture on the top of photo holder.
4. Insert the photo holder with business card fixture into the photo slot of the unit. 5. Enter media type menu to select the correct media for scanning. (Refer to P.29) Media Type 6. Press OK/Capture button to capture the image.
IV.
1. Live View Mode Live View indicator (flashing at 0.5sec rate) After a quick display of welcome page, system will enter the Live View mode. A flashing red dot appears on the top left hand corner indicating the state in Live View. (Note: select correct media type (Refer to P.29) before capturing. By default the setting is at Negative Film. Unit will reset back to the default setting after power off) 1.
1.2 Flip (Hard Key) Save & Exit OK/Capture Down/Flip Down/Flip button ● Press Down/Flip button to turn the image upside down, press again vice versa 1.
Up /+ button Press Up/+ button to increase exposure(brightness) with ranges of ‐3 to 3 ● Down/button ● Press Down/‐ button to decrease exposure(brightness) with ranges of ‐3 to 3 1.
Up /+ button ● Press Up/+ button to increase Color with ranges of ‐3 to 3 Down /button ● Press Down/‐ button to decrease Color with ranges of ‐3 to 3 Right/Go Next Left/Go Previous ● Press arrow hard key Left and Right to move between R, G, B ‐18‐
2. Capture Mode Right/Go Next Left/Go Previous OK/Capture mode Once user presses the OK/Capture hard key, the live view image is selected and wait for 2‐3 seconds to enter the Capture mode shown with four icons on the display.
2.1 Save to Memory Save icon will be highlighted for user to confirm the saving by pressing the OK/Capture button. After save action the display returns back to Live View. 2.2 Rotate +/‐90 degrees OK button User can manipulate rotate +90 or rotate ‐90 with the Left or Right button to highlight on the rotate +90/‐90 icon. Press OK/Capture button to do a clockwise or anti‐clockwise rotation and move to Save and Exit screen page.
2.3 Cancel With Cancel icon highlighted, pressing the OK/Capture button to cancel all action and return back to the state of Live View. Nothing will be saved onto the SD card. 2.4 Memory full OK button Once the internal memory or SD card is full, user can see a FULL icon showing on the display. User can either upload the saved images to PC or replace with another SD card for continuing capture.
2.5 SD card locked SD card locked icon If the SD card is locked, press the OK/Capture button will show up a SD Card Locked icon at the center of screen. Unlock the SD card by switching the bar to unlock position to continue use of the SD card. 2.6 SD card error SD card error indicator If scanner cannot detect a good working SD card in the SD slot, a warning icon with question mark will appear at the center of screen. Either format the SD card (Refer to P.
3. Playback Mode Right/Go Next Playback Mode/Setting Left/Go Previous Press the Playback button to enter the Playback Mode. 3.1 Playback Auto Slide Show Slide Show Indicator Once user enters the playback mode, a slide show indicator is showing at the top left hand corner of screen. The display will start playing all images stored in SD card or internal memory with 2 seconds interval between saved images. User can pause the slide show by pressing either the Left or Right or Mode hard key.
3.2 Playback Manual Control Pausse Left OR Right Left AND Right Single Picture Auto Slide Show Auto Slide Show Press Left AND Right button Press Left OR Right together to resume to Slide Show button to scroll picture Left Right 3.3 Playback Exit Playback button Press the Playback button to exit the Playback Mode to return to Live View Mode.
3.4 Playback Edit: Rotate+90/Rotate‐90/Mirror/Flip/Delete Right/Go Next Mode/Setting Left/Go Previous OK/Capture While at the Playback Mode, press the Mode button to enter Playback Manual Control Mode. Press the Mode button one more time to enter Playback Edit. Use Left and Right button to move to the desired icons and press OK button to confirm the action.
3.5 Playback Edit Exit Mode button Press the Mode button while at the Playback Edit Mode the display will go back to Playback Manual Control Mode on current selected picture. 3.6 Playback: Delete OK button Delete With highlight on the Delete icon press OK button will delete the current selected picture and resume back to Playback Manual Control Mode.
3.7 Playback: No Picture Playback button If there is no picture inside the internal memory or SD card when pressing the Playback button, a page with Question Mark symbol at the screen center will show up. The page will remain for 2 seconds and resume back to Live View Mode.
4. Setting Mode Mode (Hard Key) While in Live View Mode, press the Mode hard key to enter the Setting Mode.
4.
4.2 Setting: Format OK button If the internal memory or SD card requires format by scanner, user can enter Format Mode by pressing the Mode button while under the Live View Mode. Scroll to the second icon from the left and press OK button to enter format confirmation page. The highlight is at the Cancel icon by default. User can press Left or Right button to move to Confirm or Cancel icon and press the OK button.
User is able to view the images from a TV display instead of the unit’s own LCD display for bigger viewing pleasure. By connecting the AV cable to unit’s TV out jet and one end to TV, confirm by pressing OK button to select PAL or NTSC matching to TV system. The TV is now working as an alternative display to perform all tasks like scan, capture, edit and playback. 4.4 Setting: USB Mode OK button After capture user can upload the saved images from internal memory or SD card to PC by selecting USB Mode.
Good bye page ‐32‐
V. Specification Image Sensor: Lens: LCD: Internal memory: Focus Range: Exposure Control: Color Balance: Scan Quality: Data Conversion: Scan Method: Light Source: Interface: USB Configuration: Power: Dimensions: Weight: External memory: 5 mega CMOS sensor F no.=2.0, 4 Glass elements, 3.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC ID: WFZSCND503H1231 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
