SOUND 102 FM/DAB With Dock for iPod OWNER’S MANUAL
SOUND 102 OWNER’S MANUAL Need Help? Contact Us. Etón Corporation, 1015 Corporation Way, Palo Alto, CA 94303, USA. 1-800-872-2228 (U.S.); 1-800-637-1648 (Canada); 650-903-3866 (worldwide); M-F, 8:30-4:00, Pacific Standard Time; www.etoncorp.com. WARNING • Do not expose this appliance to rain or moisture. • Do not submerge or expose for extended period to water. • Protect from high humidity and rain. • Only operate within specified temperature range (0 °C to 40 °C).
SOUND 102 OWNER’S MANUAL WHAT THE ETÓN SOUND DAB RADIO INCLUDES Owner’s manual; remote control, iPOD docking station, mains power adaptor. PREPARING THE REMOTE FOR USE Grip the plastic piece on the bottom of the remote unit and pull it out. All of the controls on the Etón Sound DAB Radio are found on the remote, but only the remote has the MUTE control. If the battery drains replace it with type CR/DL2025.
SOUND 102 OWNER’S MANUAL MUTE CONTROL Press the remote’s MUTE control to mute the audio. Press it again to restore the audio. On the set, pressing the SNOOZE button, when the receiver is on, has the same function. USING THE HEADPHONES/EARPHONES Before placing headphones/earphones in/on you ears, turn the volume all the way down. Use headphones/earphones with 1/8 inch (3.5 mm) stereo plug. Plug them into the earphone socket on the back of the Etón Sound Radio.
SOUND 102 OWNER’S MANUAL DAB RECEPTION continued Auto Tuning Two types of channel scan are available, QUICK SCAN and FULL SCAN. During the scan a list is created of all the DAB services available in your area, and the set will then tune to the first service on the list. The list is in alphabetical order of the station name. Fully extend the antenna before starting the scan. A short press of AUTOTUNE will start a QUICK SCAN.
SOUND 102 OWNER’S MANUAL DAB RECEPTION continued below will also overwrite what has been previously stored into the memory. That is, a memory cannot be ‘erased’, but can be overwritten. 1. Tune to the DAB service that you wish to store. 2. Press and hold one of the 1-5 buttons on the radio or the remote to store that station into memory, as indicated in the display. ‘Preset # Saved’ is briefly shown in the display.
SOUND 102 OWNER’S MANUAL DAB RECEPTION continued ary services, and are indicated by a symbol on the top line of the display. When this indication is on, you can select the secondary service by pressing ENTER/ . To return to the original primary service, press ENTER/ again. Manual Tune Manual tune mode enables you to select individual channels to monitor the reception conditions. It is not intended for normal use.
SOUND 102 OWNER’S MANUAL FM RECEPTION continued auto-tune down the frequency, use a long, two second press. Storing into Memory Presets There are 5 memory presets in FM. Note that the procedures below will also overwrite what has been previously stored into the memory. That is, a memory cannot be ‘erased’, but can be overwritten. 1. Tune to the radio station that you wish to store. 2.
SOUND 102 OWNER’S MANUAL AUX-IN MODE To access the AUX-IN mode, sequentially press the radio’s or remote’s MODE button until FM AUX is seen in the display. The AUX-IN mode is used to run external audio through the Etón Sound DAB Radio. Such audio may be from an external MP3 player, CD, cassette unit, radio or phonograph with line out. The AUX-IN socket is on the back of the unit. iPOD MODE Play on your iPOD is started automatically when you select iPOD mode.
SOUND 102 OWNER’S MANUAL SETTING THE CLOCK continued mit the correct local time, and the clock will need to be set manually. The clock is displayed and entered in the 24 hour format. To set the clock manually, you need to turn the CLOCK SETTING to the ON state, and set the time, using the following procedure: 1. Press and hold the DISPLAY button on the remote or on the set until MANUAL TUNE is displayed. 2. Press DISPLAY quickly. CLOCK SETTING is displayed. 3. Press/release ENTER/ to confirm.
SOUND 102 OWNER’S MANUAL SETTING THE CLOCK continued AUTOMATIC CLOCK SETTING When power to the set has been interrupted, the clock will be lost. When the automatic mode is on, the set will tune to a DAB signal when the power is restored, and will attempt to automatically update the clock. If the set has been set to CLOCK SETTING ON or there is no available DAB signal with clock information, you will need to set the clock manually, as described above.
SOUND 102 OWNER’S MANUAL ALARM FUNCTIONS 5. Press/release the ENTER/ button – the minutes flash. 6. Press the TUNE buttons to adjust the minutes. 7. Press/release the ENTER/ button – the RADIO, IPOD or BUZZ symbol flashes in the display. 8. Press the TUNE buttons to select RADIO or BUZZ. 9. Press/release the ENTER/ button. The alarm activates for 30 minutes. When the alarm activates, press the POWER button to turn it off. Or press the SNOOZE button to turn off the alarm for 10 minutes.
SOUND 102 OWNER’S MANUAL SYSTEM RESET This clears all the stored presets and the DAB channel list. Use this function if the set is moved to a different location where different DAB services are transmitted. A DAB full scan is done after the reset. When in DAB mode: 1. Press DISPLAY for 2 seconds. 2. Quickly press and release DISPLAY twice – SYSTEM RESET is shown on the display. 3. Press ENTER/ . 4. After a few seconds, remove and reconnect the power connector. When in FM mode: 1.
SOUND 102 OWNER’S MANUAL WARRANTY REGSITRATION To ensure full warranty coverage or product updates, registration of your product should be completed as soon as possible after purchase or receipt. You may use one of the following options to register your product: 1. By visiting our website at http://www.etoncorp.com. 2. Mail in enclosed warranty card. 3.
SOUND 102 OWNER’S MANUAL SERVICE FOR YOUR PRODUCT continued WARRANTY – If your product is still in warranty and the Etón service representative determines warranty service is needed, a return authorization will be issued and instructions will be given. DO NOT ship your radio back without obtaining the return authorization.
SOUND 102 MANUAL D’OPÉRATION Vous avez besoin d’aide ? N’hésitez pas à nous contacter. Etón Corporation, 1015 Corporation Way, Palo Alto, CA 94303, USA. 1-800-872-2228 (États-Unis) ; 1-800-637-1648 (Canada) ; 650903-3866 (international) ; du lundi au vendredi de 8h30 à 16h00, heure du Pacifique ; www.etoncorp.com. AVERTISSEMENT • Ne pas exposer cet appareil à la pluie à l’humidité. • Ne pas plonger l’appareil dans l’eau ou le mettre en contact de l’eau pendant une période prolongée.
SOUND 102 MANUAL D’OPÉRATION FOURNI AVEC LA RADIO ETÓN SOUND DAB Manuel de l’utilisateur; commande à distance, station d’accueil iPod, adaptateur secteur. PRÉPARER VOTRE TÉLÉCOMMANDE À L’EMPLOI Effectuez une pression sur la pièce en plastique dans le bas de la télécommande et retirez-la. Toutes les commandes de la radio Etón Sound DAB Radio se trouvent sur la télécommande, mais la commande MUTE se trouve uniquement sur la télécommande. Lorsque la pile est vide, remplacez-la par une pile de type CR/DL2025.
SOUND 102 MANUAL D’OPÉRATION COMMANDE MUTE Appuyez sur la touche MUTE de la télécommande pour couper le son. Appuyez de nouveau sur cette touche pour rétablir le son. Sur la radio, appuyez sur la touche SNOOZE pendant que le récepteur est allumé, cela aura le même effet. UTILISER LES OREILLETTES/LES ÉCOUTEURS Avant de placer les oreillettes/les écouteurs dans/ sur vos oreilles, mettez par précaution le volume au minimum. Utilisez les oreillettes/les écouteurs avec une fiche stéréo de 3,5 mm (1/8 pouce).
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION DAB Programmation DAB Mettez la radio en marche. Si nécessaire, appuyez sur la touche MODE de la radio ou de la télécommande pour sélectionner le mode DAB. Programmation automatique Deux types de balayage de stations sont disponibles, QUICK SCAN et FULL SCAN. Pendant le balayage, une liste de tous les services DAB disponibles dans votre zone est créée et la radio programmera ensuite le premier service de la liste. La liste classe les stations par ordre alphabétique.
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION DAB continué Mode Auto Enter Vous pouvez modifier l’opération de façon à ce que le service DAB soit programmé automatiquement en patientant 3 secondes après l’affichage de ce service. Pour activer AUTO ENTER ON, appuyez sur ENTER/ et maintenez la touche enfoncée pendant 2 secondes. AUTO ENTER ON s’affiche. Procédez de la même manière pour afficher AUTO ENTER OFF Utiliser les présélections mémorisées Il existe 5 présélections mémorisées en mode DAB.
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION DAB continué La touche DISPLAY Appuyez séquentiellement sur la touche DISPLAY de la radio ou de la télécommande pour consulter les informations spéciales suivantes sur l’écran : 1. Nom du prestataire de services DAB 2. Heure et date 3. Informations sous forme de texte défilant 4. Intensité du signal 5. Type de programme 6.
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION DAB continué ensuite sur ENTER/ . Le numéro et la fréquence de la chaîne DAB s’affichent. Servez-vous des touches TUNE vers le haut ou vers le bas de la radio ou de la télécommande pour sélectionner la chaîne DAB. Appuyez ensuite sur ENTER/ pour sélectionner une chaîne. Servez-vous maintenant des touches TUNE vers le haut ou vers le bas pour sélectionner les services spécifiques de la chaîne DAB. Pour sortir du mode Manual Tune, appuyez une nouvelle fois sur ENTER.
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION FM continué Utiliser les présélections mémorisées Il existe 5 présélections mémorisées en mode FM. Notez que le processus décrit ci-dessous va également remplacer le contenu qui avait été mémorisé auparavant. Il ne s’agit pas de ‘supprimer’ une mémoire, mais de modifier son contenu. 1. Recherchez la station de radio que vous souhaitez mémoriser. 2.
SOUND 102 MANUAL D’OPÉRATION RÉCEPTION FM continué 4. Heure/ Date 5. I ndicateur d’intensité du signal MODE AUX-IN Pour passer en mode AUX-IN, appuyez séquentiellement sur la touche MODE de la radio ou de la télécommande jusqu’à ce que FM AUX apparaisse sur l’écran. Le mode AUX-IN sert à diffuser le son d’appareils audio externes par le biais de la radio Etón Sound DAB. Il peut s’agit d’un lecteur MP3 externe, d’un CD, d’un magnétophone à cassettes, d’une radio ou d’un électrophone avec sortie de ligne.
SOUND 102 MANUAL D’OPÉRATION PRISE LINE-OUT Le mode LINE-OUT sert à diffuser le son stéréo de la radio Etón Sound DAB vers une enceinte externe préamplifiée ou un haut-parleur stéréo. La prise LINE-OUT se trouve au dos de la radio. PROGRAMMER L’HEURE La plupart des services DAB services fournissent des informations sur l’heure, ce qui permet à la radio ES102 de programmer l’heure avec précision lorsque la radio a été programmée quelques secondes auparavant.
SOUND 102 MANUAL D’OPÉRATION PROGRAMMER L’HEURE continué 9. Appuyez/ Relâchez le bouton ENTER/ . Pour passer du réglage de l’heure en mode automatique : 1. Appuyez sur la touche DISPLAY de la radio ou de la télécommande et maintenez-la enfoncée jusqu’à ce que MANUAL TUNE s’affiche. 2. Appuyez rapidement sur DISPLAY. CLOCK SETTING apparaît. 3. Appuyez/ Relâchez la touche ENTER/ pour confirmer. ON clignote sur l’écran. 4. Appuyez sur la touche TUNE – ou TUNE + pour faire passer l’écran sur OFF. 5.
SOUND 102 MANUAL D’OPÉRATION FONCTIONS ALARME continué la lecture commencera à partir du dernier titre écouté. Note : si la radio est en mode AUX, seule l’opération BUZZER est possible. Régler et activer l’heure de l’alarme et le mode de réveil Pour le réglage de l’alarme, la radio peut être en marche ou en mode veille, en mode DAB, FM ou iPOD. Utilisez les touches de la radio ou de la télécommande. Contrôlez l’écran. 1.
SOUND 102 MANUAL D’OPÉRATION FONCTIONS ALARME continué sur la touche SNOOZE pour éteindre l’alarme pendant 10 minutes. La touche Snooze Une fois que l’alarme se déclenche, appuyez sur la touche SNOOZE de la radio ou de la télécommande pour passer en mode snooze. Le mode snooze fonctionne pendant 10 minutes, puis l’alarme se déclenche de nouveau. La fonction SNOOZE peut être activée 3 fois. LA FUNCTION SLEEP La fonction SLEEP éteint la radio après une durée préprogrammée.
SOUND 102 MANUAL D’OPÉRATION ANNULATION DE LA MISE À ZÉRO Ceci annule toutes les présélections enregistrées ainsi que la liste de chaînes DAB. Utilisez cette fonction si la radio se trouve à un endroit différent de celui où les différents services DAB sont transmis. Un full scan DAB est effectué après la remise à zéro. En mode DAB : 1. Appuyez sur la touche DISPLAY pendant deux secondes. 2. Appuyez brièvement sur la touche DISPLAY et relâchez-la à deux reprises – SYSTEM RESET apparaît sur l’écran. 3.
SOUND 102 MANUAL D’OPÉRATION SPÉCIFICATIONS continué • Ces spécifications, ainsi que le design, pourront être éventuelles modifiées sans que cette amélioration ne soit mentionnée. ENREGISTREMENT DE LA GARANTIE Il est conseillé d’effectuer l’enregistrement de votre produit dès que possible après l’achat ou la réception afin d’assurer une couverture de garantie complète ou les mises à jour du produit. Vous pouvez enregistrer votre produit de trois manières différentes : 1.
SOUND 102 MANUAL D’OPÉRATION SERVICE DE GARANTIE POUR VOTRE PRODUIT Pour bénéficier d’un service de garantie pour votre produit, nous vous conseillons de contacter en premier lieu un représentant du service de garantie Etón au 1-800-872-2228 pour les États-Unis, 1800-637-1648 pour le Canada ou (650) 903-3866, customersvc@ etoncorp.com ou le revendeur dans votre pays en Europe (voir liste ci-jointe) qui constatera le problème et vous dépannera.
Bedienungsanleitung SOUND 102 Hotline und Anschrift Etón Corporation, 1015 Corporation Way, Palo Alto, CA 94303, USA. 1-800-872-2228 (USA); 1-800-637-1648 (Kanada); 650-9033866 (weltweit); Mo.-Fr.: 08:30-16:00 (Pazifische Standardzeit); www.etoncorp.com. ACHTUNG • Das Gerät darf weder mit Wasser noch mit Feuchtigkeit in Berührung kommen. • Tauchen Sie das Gerät nicht in Wasser. • Schützen Sie das Gerät vor hoher Luftfeuchtigkeit und Regen.
Bedienungsanleitung SOUND 102 LIEFERUMFANG Bedienungsanleitung, Fernbedienung, Docking Station für iPod, Netzteil. VOR DER INBETRIEBNAHME DER FERNBEDIENUNG Das Kunststoffteil unterhalb der Fernbedienung herausziehen. Die Fernbedienung verfügt über die gleichen Funktionsregelungen wie das Etón Sound DAB Radiogerät und zusätzlich über die MUTE-Taste (Stummschaltung). Nur Batterien vom Typ CR/DL2025 verwenden.
Bedienungsanleitung SOUND 102 MUTE-Taste (Stummschaltung) Um den Ton abzustellen die MUTE-Taste auf der Fernbedienung drücken. Durch erneutes Drücken wird der Ton wieder eingeschaltet. Die SNOOZE-Taste am Kombigerät bei eingeschaltetem Receiver hat die gleiche Funktion wie die MUTE-Taste auf der Fernbedienung. Verwendung von Kopf-/Ohrhörern Vor dem Aufsetzen der Kopf-/Ohrhörer die Lautstärke komplett nach unten regulieren. Kopf-/Ohrhörer mit 3,5-mm-Stereoanschluss verwenden.
Bedienungsanleitung SOUND 102 DAB-Empfang DAB-Einstellungen Radio einschalten. Ggf. MODE-Taste am Gerät oder auf der Fernbedienung drücken, um DAB Modus auszuwählen. Automatische Sendersuche Es stehen zwei Varianten des Sendersuchlaufs zur Verfügung: QUICK SCAN (schneller Suchlauf) und FULL SCAN (vollständiger Suchlauf). Während des Suchlaufs wird eine Liste von allen verfügbaren DABServices in dem entsprechenden Empfangsbereich erstellt. Das Gerät wählt dann den ersten Service aus der Liste.
Bedienungsanleitung SOUND 102 DAB-Empfang fortgefahren Automatischer Enter-Modus Die Einstellungen lassen sich dahingehend ändern, dass der DABService, der 3 s lang auf dem Display angezeigt wird, automatisch eingestellt wird. Dazu muss AUTO ENTER ON aktiviert werden, indem die Taste ENTER/ für 2 s gedrückt wird. Auf dem Display erscheint AUTO ENTER ON. Durch erneutes Drücken der Taste ENTER/ für 2 s wird die Funktion wieder deaktiviert und es erscheint AUTO ENTER OFF.
Bedienungsanleitung SOUND 102 DAB-Empfang fortgefahren DISPLAY-Taste Durch mehrfaches Drücken der DISPLAY-Taste am Radio oder auf der Fernbedienung werden jeweils unterschiedliche Informationen (siehe unten) angezeigt. 1. Name des DAB-Service-Providers 2. Uhrzeit und Datum 3. laufende Textinformationen 4. Signalstärke 5. Programmart/-sparte 6.
Bedienungsanleitung SOUND 102 DAB-Empfang fortgefahren und Frequenz werden angezeigt. Über die Tasten TUNE oder am Gerät oder auf der Fernbedienung den DAB-Kanal wählen. Zur Auswahl eines Kanals die Taste ENTER/ drücken. Über die Tasten TUNE oder können nun die einzelnen Services auf dem DABKanal ausgewählt werden. Zum Verlassen des Senderwahlmodus erneut ENTER drücken. UKW-Empfang UKW-Einstellungen Radio einschalten. Am Gerät oder auf der Fernbedienung die MODETaste zur Auswahl DAB FM drücken.
Bedienungsanleitung SOUND 102 UKW-Empfang fortgefahren Abspeichern von Lieblingssendern Das Gerät verfügt über 5 Speicherplätze für UKW-Lieblingssender. Hinweis: Speicher können nicht gelöscht werden, sondern lediglich durch die nachfolgend beschriebene Prozedur überschrieben werden. 1. Den gewünschten Radiosender einstellen. 2. Durch anhaltendes Drücken einer der Tasten 1-5 am Gerät oder auf der Fernbedienung wird dieser Sender auf dem im Display angezeigten Speicherplatz abgelegt.
Bedienungsanleitung SOUND 102 UKW-Empfang fortgefahren 5. Signalstärkeanzeige Modus AUX-IN Am Gerät oder auf der Fernbedienung die MODE-Taste so oft drücken, bis im Display FM AUX erscheint. Über den Modus AUX-IN lassen sich externe Audioquellen über das Etón Sound DAB Radio betreiben. Auf diese Weise können MP3-Player, CD-Spieler, Kassettenrecorder, Radio oder Plattenspieler mit Ausgangsleitung angeschlossen werden. Der Steckplatz AUX-IN befindet sich an der Rückseite des Geräts.
Bedienungsanleitung SOUND 102 Steckplatz LINE-OUT Im Modus LINE-OUT kann der Stereoausgang des Geräts an ein vorverstärktes, externes Lautsprechersystem oder eine Stereoanlage angeschlossen werden. Der Steckplatz LINE-OUT befindet sich an der Rückseite des Geräts. Uhrzeit einstellen Die meisten DAB-Services senden die aktuelle Uhrzeit, so dass das ES102 die Uhrzeit genau einstellen kann, nachdem das Gerät einige Sekunden lang auf den Sender eingestellt ist.
Bedienungsanleitung SOUND 102 Uhrzeit einstellen fortgefahren 9. ENTER/ Taste drücken/loslassen. Rücksetzung der Uhrzeiteinstellung auf automatischen Modus: 1. Die DISPLAY-Taste auf der Fernbedienung oder am Gerät solange drücken, bis MANUAL TUNE angezeigt wird. 2. Kurz DISPLAY drücken. Im Display erscheint CLOCK SETTING. 3. Zur Bestätigung ENTER/ Taste drücken/loslassen. Auf dem Display erscheint ON. 4. Mit den Tasten TUNE – oder TUNE + kann im Display auf OFF gewechselt werden. 5.
Bedienungsanleitung SOUND 102 Weckfunktionen fortgefahren Hinweis: Wenn das Gerät auf Modus AUX eingestellt ist, erfolgt das Wecken nur über den BUZZER Einstellung und Aktivieren der Weckzeit und des Weckmodus Die Weckzeit lässt sich sowohl im Standby-Modus als auch bei eingeschaltetem Radio mit DAB-/UKW- oder IPOD-Modus einstellen. Tasten auf dem Gerät oder der Fernbedienung verwenden und das Display beobachten. 1. Taste ALARM ca. 2 s lang gedrückt halten, dann wieder loslassen.
Bedienungsanleitung SOUND 102 Weckfunktionen fortgefahren Taste SNOOZE Durch Drücken der Taste SNOOZE am Gerät oder auf der Fernbedienung bei laufendem Alarm wird der Schlummermodus aktiviert. Der Schlummermodus dauert 10 Minuten, danach wird der Alarm wieder eingeschaltet. Die SNOZZE-Taste und somit die Schlummerfunktion kann 3 Mal aktiviert werden. SLEEP Timer Diese Funktion schaltet das Gerät nach einer vorgegeben Zeit aus. Bei eingeschaltetem Gerät den SLEEP Timer wie folgt aktivieren: 1.
Bedienungsanleitung SOUND 102 System Reset Im DAB-Modus: 1. 2 s lang DISPLAY drücken. 2. Zweimal kurz DISPLAY drücken und wieder loslassen. Im Display erscheint SYSTEM RESET. 3. ENTER/ Taste drücken. 4. Stecker nach ein paar Sekunden ziehen und wieder anschließen. Im FM-Modus: 1. 2 s lang DISPLAY drücken. 2. DISPLAY erneut drücken. 3. ENTER drücken. 4. Die UKW-Anzeige springt auf 87,5 MHz zurück.
Bedienungsanleitung SOUND 102 Produktregistrierung fortgefahren dates zu gewährleisten. Zur Registrierung stehen Ihnen verschiedene Möglichkeiten zur Verfügung: 1. Auf unserer Webseite unter http://www.etoncorp.com. 2. Rücksenden der beigefügten Garantiekarte. 3.
Bedienungsanleitung SOUND 102 Kundendienst fortgefahren MIT GARANTIE – Sollte das Gerät innerhalb der Garantiezeit eine Reparatur benötigen, erhalten Sie eine Genehmigungsnummer für die Rücksendung sowie Informationen zum Versand. Senden Sie das Gerät NICHT ohne Genehmigungsnummer zurück. OHNE GARANTIE – Sollte die Garantiezeit bereits abgelaufen und eine Reparatur erforderlich sein, wird Sie unser Mitarbeiter an den nächstgelegenen und für die Reparatur fachlich geeigneten Kundendienst verweisen.
SOUND 102 MANUALE DI ISTRUZIONI Serve Aiuto? Contattateci. Etón Corporation, 1015 Corporation Way, Palo Alto, CA 94303, USA. 1-800-872-2228 (U.S.); 1-800-637-1648 (Canada); 650-9033866 (resto del mondo); M-F, 8:30-4:00, ora del Pacifico; AVVERTENZA • Non esporre l’apparecchio alla pioggia e all’umidità. • Non immergere e non esporre l’apparecchio all’acqua per periodi prolungati. • Tenere al riparo dalla pioggia e dall’elevata umidità.
SOUND 102 MANUALE DI ISTRUZIONI Dotazioni dell’EtÓn Sound DAB Radio Manuale d’impiego; telecomando, base iPOD, adattatore di corrente. Predisposizione del telecomando all’uso Afferrare la linguetta di plastica posta in fondo al telecomando e rimuoverla. Il telecomando contiene tutti i comandi presenti sull’Etón Sound DAB Radio, ma solo il telecomando dispone del comando MUTE. Sostituire le batterie scariche con batterie di tipo CR/DL2025.
SOUND 102 MANUALE DI ISTRUZIONI Comando Mute Premendo il tasto MUTE del telecomando è possibile togliere l’audio. Premere nuovamente il tasto per ripristinare l’audio. Analogamente, premendo il tasto SNOOZE sull’apparecchio quando il ricevitore è acceso, è possibile togliere l’audio. Utilizzo delle cuffie/degli auricolari Prima di mettere le cuffie o inserire gli auricolari, abbassare completamente il volume. Utilizzare cuffie/auricolari con presa stereo da 3,5 mm.
SOUND 102 MANUALE DI ISTRUZIONI RICEZIONE DAB Sintonizzazione DAB Accendere la radio. Se necessario, premere il tasto MODE sulla radio o sul telecomando per selezionare la modalità DAB. Sintonizzazione automatica Sono presenti due tipi di ricerca dei canali, la ricerca veloce QUICK SCAN e la ricerca completa FULL SCAN. Durante la ricerca viene creato un elenco di tutti i servizi DAB disponibili nella zona e l’apparecchio si sintonizzerà sul primo servizio dell’elenco.
SOUND 102 MANUALE DI ISTRUZIONI RICEZIONE DAB continuato Modalità di registrazione automatica È possibile fare in modo che il servizio DAB venga sintonizzato automaticamente dopo 3 secondi dalla visualizzazione del servizio. Per attivare la funzione AUTO ENTER, tenere premuto il tasto ENTER/ per 2 secondi. Viene visualizzato il messaggio AUTO ENTER ON. Seguire la stessa procedura per disattivare la funzione AUTO ENTER (AUTO ENTER OFF).
SOUND 102 MANUALE DI ISTRUZIONI RICEZIONE DAB continuato Il tasto DISPLAY Premere più volte il tasto DISPLAY sulla radio o sul telecomando per visualizzare le informazioni speciali sul display, come indicato di seguito. 1. Nome del provider del servizio DAB 2. Ora e data 3. Informazioni di testo scorrevoli 4. Intensità del segnale 5. Tipo di programma 6.
SOUND 102 MANUALE DI ISTRUZIONI RICEZIONE DAB continuato up o down sull’apparecchio o sul telecomando per selezionare il canale DAB. Per selezionare un canale premere ENTER/ . I tasti TUNE up o down possono ora essere utilizzati per selezionare i singoli RICEZIONE FM Sintonizzazione FM Accendere la radio. Premere il tasto MODE dell’apparecchio o del telecomando per selezionare DAB FM. Sul display viene visualizzato FM.
SOUND 102 MANUALE DI ISTRUZIONI RICEZIONE FM continuato 2. Tenere premuto uno dei tasti da 1 a 5 sulla radio o sul telecomando per memorizzare la stazione, come indicato sul display. Sul display compare brevemente ‘Preset # Saved’ (posizione memoria preimpostata salvata). Accedere alla memoria preimpostata • Premere brevemente i tasti 1-5 del telecomando per selezionare la stazione memorizzata desiderata.
SOUND 102 MANUALE DI ISTRUZIONI Modalità AUX-IN continuato radio o un fonografo con porta line out. L’attacco AUX-IN è collocato nella parte posteriore dell’apparecchio. Modalità iPOD L’iPOD viene attivato automaticamente quando si seleziona la modalità iPOD. È possibile utilizzare il telecomando per gestire le funzioni dell’iPOD. Utilizzare il tasto MENU per scorrere il menu iPOD. Utilizzare i tasti up o down per scorrere il menu verso l’alto o verso il basso.
SOUND 102 MANUALE DI ISTRUZIONI Impostazione dell’orologio continuato Per regolare l’orologio manualmente, è necessario attivare la modalità CLOCK SETTING (regolazione dell’orologio ON) e impostare l’ora, seguendo la procedura descritta di seguito: 1. Tenere premuto il tasto DISPLAY del telecomando o sull’apparecchio fino a che compare MANUAL TUNE. 2. Premere brevemente DISPLAY. Viene visualizzato CLOCK SETTING (impostazione ora). 3. Premere/rilasciare ENTER/ per confermare. Sul display lampeggia OFF. 4.
SOUND 102 MANUALE DI ISTRUZIONI Impostazione dell’orologio continuato 5. Premere/rilasciare il tasto enter 3 volte per tornare alla funzione normale. Impostazione automatica dell’orologio Quando l’apparecchio rimane senza alimentazione, l’ora va persa. Se la modalità automatica è attivata, una volta ripristinata l’alimentazione l’apparecchio si sintonizzerà su un segnale DAB e cercherà di aggiornare automaticamente l’ora.
SOUND 102 MANUALE DI ISTRUZIONI Funzioni sveglia continuato tivando la sveglia. 3. Premere/rilasciare il tasto ENTER/ – l’ora lampeggia. 4. Premere i tasti TUNE per regolare l’ora. 5. Premere/rilasciare il tasto ENTER/ – i minuti lampeggiano. 6. Premere i tasti TUNE per regolare i minuti. 7. Premere/rilasciare il tasto ENTER/ – I simboli RADIO, iPOD o BUZZ lampeggiano sul display. 8. Premere i tasti TUNE per selezionare RADIO o BUZZ. 9. Premere/rilasciare il tasto ENTER/ . La sveglia suona per 30 minuti.
SOUND 102 MANUALE DI ISTRUZIONI Lo SLEEP Timer continuato 1. Premere SLEEP per due secondi. Viene visualizzato SLEEP e OFF lampeggia. 2. Premere TUNE+ / TUNE- sul telecomando o sull’apparecchio per selezionare ON o OFF. 3. Premere ENTER/ . 4. Premere TUNE+ / TUNE- sul telecomando o sull’apparecchio per selezionare la funzione sleep per un intervallo di tempo da 15 a 90 minuti. 5. Premere ENTER/ . Quando la funzione sleep è attiva viene visualizzata la lettera “S” nella prima riga del display.
SOUND 102 MANUALE DI ISTRUZIONI Reset del sistema continuato Quando l’apparecchio è in modalità FM: 1. Premere DISPLAY per 2 secondi. 2. Premere nuovamente DISPLAY. 3. Premere ENTER. 4. Si noti che la frequenza FM torna a 87,5 MHz. DATI TECNICI • Frequenza FM 87.5 – 108.
SOUND 102 MANUALE DI ISTRUZIONI REGISTRAZIONE DELLA GARANZIA continuato numero di telefono, l’indirizzo e-mail, il modello acquistato, la data di acquisto, il nome del rivenditore: Etón Corporation 1015 Corporation Way Palo Alto, CA 94303 USA GARANZIA LIMITATA Conservare le informazioni relative alla garanzia presenti sul certificato di garanzia stesso insieme alla ricevuta dell’acquisto; è possibile consultare le informazioni relative alla garanzia limitata all’indirizzo www.etoncorp.com.
SOUND 102 MANUALE DI ISTRUZIONI ASSISTENZA PER IL PRODOTTO ACQUISTATO continuato INTERVENTI NON COPERTI DA GARANZIA – Se l’apparecchio non è più coperto da garanzia e si rende necessario un intervento di riparazione, il servizio clienti Etón vi indicherà il centro di assistenza più vicino a voi, cui rivolgersi per le riparazioni. Per assistenza al di fuori del Nord America, fare riferimento all’elenco dei distributori fornito al momento dell’acquisto/ricevimento.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 ¿Necesita ayuda? ¡Contáctenos! Etón Corporation, 1015 Corporation Way, Palo Alto, CA 94303, EE.UU. 1-800-872-2228 (EE.UU.); 1-800-637-1648 (Canadá); 650903-3866 (todo el mundo); Lunes a viernes, 8.30-16.00 hrs., Hora Estándar del Pacífico; www.etoncorp.com. ADVERTENCIA • No exponga este dispositivo a lluvia o humedad. • No exponga o sumerja este aparato al agua durante un período largo. • Proteja el aparato de gran humedad y lluvia.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Volumen de suministro de su EtÓn Sound DAB Radio Manual de usuario, control remoto, estación de cuna para iPod, adaptador principal de corriente. Preparación del control remoto para el uso Sujete la pieza plástica en la parte inferior de la unidad remota para extraerla. Todas las funciones de control de la Etón Sound DAB Radio se encuentran disponibles también en el control remoto, pero sólo el control remoto cuenta con la función MUTE.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Control de volumen continuado agujas del reloj reduce el volumen. La pulsación del botón VOL aumenta el volumen, mientras que la pulsación del botón VOL reduce el volumen. Botón Mute Utilice el botón MUTE en el control remoto para dejar la radio en mudo. Mediante su nueva pulsación se restablece el audio. En el dispositivo, el botón SNOOZE tiene la misma función mientras el receptor está activado.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Recepción DAB Sintonización de DAB Encienda la radio. En caso dado, pulse el botón MODE en la radio o en el control remoto para seleccionar el modo DAB. Sintonización automática Están disponibles dos tipos de canales: QUICK SCAN y FULL SCAN. Durante el escaneo se genera una lista de todos los servicios DAB disponibles en su área y el equipo sintoniza luego el primer servicio indicado en esta lista.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Recepción DAB continuado Modo de entrada automática Usted puede cambiar la operación de modo que el servicio DAB se sintoniza automáticamente después de esperar 3 segundos tras la indicación del servicio. Para activar la función AUTO ENTER, debe pulsarse y mantenerse pulsado durante 2 segundos el botón ENTER/ . Luego se indica AUTO ENTER ON. Utilice el mismo procedimiento para desactivar la función con AUTO ENTER OFF.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 El botón DISPLAY Pulse secuencialmente el botón DISPLAY en la radio o en el control remoto para ver la información específica en la pantalla, tal como se indica a continuación. 1. Nombre del proveedor de servicio DAB 2. Hora y fecha 3. Información de texto scroll 4. Intensidad de señal 5. Tipo de programa 6.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 AJUSTE DEL TEMPORIZADOR frecuencia del canal DAB. Utilice los botones TUNE (Sintonizar hacia arriba) o bien (Sintonizar hacia abajo) en el dispositivo o control remoto para seleccionar el canal DAB. Para seleccionar un canal, pulse ENTER/ . Los botones TUNE o pueden usarse ahora para la selección de servicios individuales en el canal DAB. Para salir del modo de sintonización manual, pulse nuevamente ENTER. RECEPCIÓN FM Sintonización de FM Encienda la radio.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 RECEPCIÓN FM continuado no se puede eliminar, pero sí se puede sobreescribir. 1. Sintonice la estación de radio que desea almacenar. 2. Pulse y mantenga pulsado uno de los botones 1 a 5 en la radio o en el control remoto para almacenar la estación en la memoria, tal como se indica en la pantalla. ‘Preset # Saved’ se indica brevemente en la pantalla.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Modo AUX-IN Para acceder al modo AUX-IN, debe pulsarse secuencialmente el botón MODE en el dispositivo o en el control remoto hasta que se indique FM AUX en la pantalla. El modo AUX-IN sirve para utilizar el audio externo a través de la Etón Sound DAB Radio. Este audio puede ser un dispositivo externo de MP3, CD, una unidad de casete o radio o bien un tocadiscos con salida de línea. El enchufe AUX-IN se encuentra en la parte posterior de la unidad.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Ajuste del reloj La mayoría de los servicios DAB transmiten la información de hora que permite al ES102 el ajuste preciso de la hora después de haber sintonizado el dispositivo durante algunos segundos. En algunas regiones, las transmisiones DAB no transmiten correctamente la hora local y el reloj se debe ajustar manualmente. El reloj se indica e ingresa en formato de 24 horas.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Ajuste del reloj continuado Para conmutar el ajuste de reloj nuevamente al modo automático: 1. Pulse y mantenga pulsado el botón DISPLAY en el control remoto o dispositivo hasta que se indique MANUAL TUNE (Sintonización manual). 2. Pulse brevemente el botón DISPLAY. Se indica CLOCK SETTING (Ajuste de reloj). 3. Pulse/libere el botón ENTER/ para confirmar. El mensaje ON parpadea en la pantalla. 4. Pulse los botones TUNE – o TUNE + para desactivar (OFF) la pantalla. 5.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Funciones de alarma continuado última canción tocada. Nota: En caso que la radio esté ajustada en modo AUX, se puede conmutar sólo al modo BUZZER. Ajuste y activación de la hora de alarma y del modo de despertar Para ajustar la alarma, la radio puede estar en modo standby o bien activado, en el modo DAB, FM o iPod. Utilice los botones en la radio o en el control remoto. Mire la pantalla. 1.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Funciones de alarma continuado La alarma se activa para 30 minutos. Cuando se activa la alarma, pulse el botón POWER para apagarla. O bien pulse el botón SNOOZE para apagar la alarma para 10 minutos. El botón Snooze Una vez que esté activada la alarma, pulse el botón SNOOZE en la radio o en el control remoto para ingresar al modo Snooze. El modo Snooze tiene una duración de 10 minutos, luego se activa nuevamente la alarma. SNOOZE se puede activar 3 veces.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 Restauración del sistema Para eliminar todos los preajustes almacenados y la lista de canales DAB. Utilice esta función en caso de haber llevado el dispositivo a otra región o ubicación donde los servicios DAB transmitidos resultan diferentes. Se realiza un escaneo completo de DAB después de la restauración. En modo DAB: 1. Pulse DISPLAY durante dos segundos. 2.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 ESPECIFICACIONES continuado • Las especificaciones y el diseño están sujetas a eventuales modificaciones sin aviso previo, con el propósito de aplicar mejoras. REGISTRO DE GARANTÍA Para asegurar la cobertura completa de la garantía o adquirir actualizaciones del producto, debe registrar su producto tan pronto posible después de la compra o recibo del producto. Usted puede utilizar una de las siguientes opciones para registrar su producto: 1.
GUÍA DE FUNCIONADMIENTO DE SOUND 102 SERVICIO PARA SU PRODUCTO Para solicitar algún servicio para su producto, le recomendamos contactar primero al representante de servicio de Etón llamando al número de teléfono 1-800-872-2228 para los EE.UU., o al número de teléfono 1-800-637-1648 para Canadá ó (650) 903-3866, customersvc@etoncorp.com o bien su distribuidor respectivo del país dentro de Europa (véase la lista adjunta) para la localización y resolución del problema.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Etón Corporation Corporate Headquarters 1015 Corporation Way Palo Alto, California 94303 USA tel +1 650-903-3866 tel +1 800-872-2228 fax +1 650-903-3867 Etón Europe/Lextronix Germany Rosenstrasse 2 D-10178 Berlin, Germany tel +49 [0]30 243102142 Etón Canada 1 Yonge Street, Suite 1801 Toronto, Ontario M5E 1W7 Canada tel +1 416-214-6885 Designed by Etón California and assembled in China. I © Copyright 2007 Etón Corporation. All rights reserved. v.