Instructions / Assembly

ManualsBrandsETi ManualsLED Tube Lights4 ft. 32W Equivalent Linear T8 Double End Power Integral Driver LED Tube Light Bulb 120-277V 5000K Daylight (25-Pack)

Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday

1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com

Ordering # 64101143

64101163

Part # T8BP-4-12-840-MV-DE-PET

T8BP-4-12-850-MV-DE-PET

Certiﬁcation # 64101143

64101163

USE AND CARE GUIDE

LED BALLAST BYPASS TUBE WITH SHATTER RESISTANT COATING

NOTE: Keep your receipt and these instructions for proof of purchase

WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old ﬁxture, ballast, or ﬂuorescent tubes.

If you are unfamiliar with electrical installations, we recommend you contact a qualiﬁed electrician to do the installation.

INSTALLATION

1. Shut off power at the electrical panel before beginning the installation.

2. Remove existing ﬂuorescent tubes and set aside to recycle in accordance with local requirements.

3. Remove and set aside the ballast cover, if needed.

4. Use the existing shunted sockets if they in good condition. If not, it is recommended that new shunted sockets (not included)

are installed.

47 3/4”

1”

RETROFIT LUMINAIRE WITH 1 LAMP

INSTANT START

PROGRAM START OR RAPID START

WARNING:

• Risk of ﬁre or electric shock. Installation of this LED Retroﬁt requires a person familiar with the construction and operation of the light ﬁxture’s/luminaire’s electrical system and the

hazard involved. If not qualiﬁed, do not attempt installation. Contact a qualiﬁed electrician.

• Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so so could lead to electric shock, ﬁre, or other

injuries which could be hazardous or even fatal.

• Install only in luminaires (light ﬁxtures) that have the construction features and dimensions shown in the photographs and/or drawings included in these installation instructions.

• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION: Not for emergency lighting.

WARNING: THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING

JURISDICTION. • Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing

lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors. • THERE ARE LED TUBE, OPERATION

INSTRUCTION AND FIELD APPLIED LABEL IN THIS RETROFIT KIT. • This device is not intended for use with emergency exits. • Not suitable for use in vapor tight luminaires (light

ﬁxtures).

The units covered by this report were intended to be retroﬁt surface mounted with a diffuser for this model number. Type IC and non-IC recessed mounted ﬂuorescent luminaires use a

maximum of two lamps, the minimum lamp compartment dimensions are below:

Model

Number

Minimum Lamp Compartment Dimensions

[Length x Width x Height] [in]

Maximum Lamp

Quantity

641011XX 48.4 x 13.4 x 1.7 4

NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which

the receiver is connected, and consult the dealer or an experienced radio/TV. Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.

Electronic

Ballast

Electronic

Ballast

Fluorescent lamp

LED lamp

Fluorescent lamp

LED lamp

PACKAGE CONTENTS

Part Description Quantity

A LED Tube 1

B UL Safety Sticker 1

Summary of content (3 pages)

PAGE 1
Ordering # 64101143 64101163 Part # T8BP-4-12-840-MV-DE-PET T8BP-4-12-850-MV-DE-PET Certification # 64101143 64101163 Use and Care Guide LED Ballast Bypass Tube with Shatter Resistant Coating Package Contents NOTE: Keep your receipt and these instructions for proof of purchase WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
PAGE 2
N° de commande 64101143 64101163 N° de pièce T8BP-4-12-840-MV-DE-PET T8BP-4-12-850-MV-DE-PET N° de certification 64101143 64101163 GUIDE D’UTILISATION ET D’ENTRETIEN Tube DEL sans ballast avec enduit résistant à l’éclatement CONTENU DE L’EMBALLAGE REMARQUE : Gardez votre facture ainsi que ces instructions comme preuves d’achat. AVERTISSEMENT : Coupez le courant au panneau de disjoncteurs ou de fusibles avant d’enlever le vieux luminaire, le ballast ou les tubes fluorescents.
PAGE 3
Pedido # 64101143 64101163 Parte # T8BP-4-12-840-MV-DE-PET T8BP-4-12-850-MV-DE-PET Certificación # 64101143 64101163 MANUAL DE USO Y CUIDADO Tubo LED sin balastos con revestimiento resistente a roturas Contenido del paquete NOTA: Guarde el recibo de compra y estas instrucciones como prueba de compra. ADVERTENCIA: Apague la corriente en el cajetín de interruptores automáticos o fusibles antes de retirar el viejo accesorio, balastro o tubos fluorescentes.