Users Manual

ManualsBrandsEstone Technology ManualsElectronicscontrol panel and relay box

Table Of Contents

Control Panel IRVC1

User Manual

Warning

RV manufacturers may make different wiring and wire colors for different RV floor plan. You

must ask RV manufacturers for proper instructions before any installation or modification of

this product. Wrong connections of wires may damage devices, cause fire or other lethal

result.

You must contact the RV manufacturer or their authorized service for repairing or

modification of this product. Do not attempt to disassemble or adjust this product by

unauthorized person.

Always disconnect the product from power source (battery, converter, solar power. Etc.)

before removal, repairing, or installation of this product.

Read this User Manual carefully before using this product. Failure to follow the instructions

could result in personal injury, including death.

Check RV and its surroundings carefully, especially the slides and awning area, before

operations

Must keep unauthorized users, especially children, away from this device

This product must be installed or stored in dry area. Do not expose this product to moisture or

water.

The device manufacture is not liable if the users violates the instructions in this manual.

Summary of content (9 pages)

PAGE 1
3 The device manufacture is not liable if the users violates the instructions in this manual. This product must be installed or stored in dry area. Do not expose this product to moisture or water. Must keep unauthorized users, especially children, away from this device Check RV and its surroundings carefully, especially the slides and awning area, before operations Read this User Manual carefully before using this product.
PAGE 2
4 Figure 2 The utility buttons are for control of lights, heaters, or pumps. When pressed, a LED next to the button will lit up and indicate the on/off status. Please note that the names on these buttons may be different by RV floor plan. 1.2 Utility Buttons Figure 1 Figure 1 is a standard IRVC1 photo, which can control 5 slides, 2 awnings, 6 water tanks, and 10 utilities (lights, heaters, pumps). Because of differences in RV floor plans, some models may offer less slides, awnings, and water tanks.
PAGE 3
5 The battery capacity LCD will be on constantly. IRVC1 can monitor up to 6 water tanks. The water level LED is only lit for 1 minute and goes to blank if no action. You must press the Tank Reading button again to resume the water level display. Figure 4 1.4 Monitor Battery and Water Levels Figure 3 Press the Select button to select the desired slide or awning, then press the Retract or Extend button to operate the slide and awning.
PAGE 4
6 Notes: 1. If your search in app cannot find iRVC1, it will be the following: o The phone is not within 1FT of iRVC1. o iRVC1 is connected to another phone. This phone must be disconnected (or put 50ft away from RV) in order for your phone to pair. 2. Only one phone can be connected at a time. 3. If your phone has not connected to iRVC1 for 7 days, you must do pairing again. This is a safety design. The pairing is easy. After you open iRV Control App, you simply follow the onscreen message.
PAGE 5
7 2.3 User interface of different functions. 4. iRVC1 cannot be detected and paired by normal phone Bluetooth search.
PAGE 6
8 After the panel replies “Hello”, you have 10 seconds to speak a complete voice 3.4 Time out of voice control again and do the next function. After waking up, you can speak one command only. You must speak “Hello RV” 3.3 One voice command a time voice command. For example, if you say Turn” + Entry Light” + on”, the panel will ignore your (see above photo) to operate. You must say the exact words and cannot change order.
PAGE 7
Figure 8 Figure 7 9 Maximumdistance between panel and phone ⋯⋯⋯ 50ft Chassis Outline Dimension⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯7.62(W)*4.97(H)*1.03(D) Operating Temperature ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯-20~60℃ Minimum Operating Voltage ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯11.3V Maximum Operating Voltage⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯14.4V 4.2 Specifications: The IO in Figure 7 connects to IRV relay box by any standard RJ-45 cable. It is CAN and 12V DC input combo port. Note: do not connect to any network port. It will not work and may damage the unit.
PAGE 8
10 Figure 9 See the mounting hole diagram to measure and cut a mounting Hole. Use four #8 PH (0.164” x 0.75”) screws. 4.
PAGE 9
installed and operated with minimum distance 20cm between the radiator & your body. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be -Consult the dealer or an experienced radio/TV technician for help. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Increase the separation between the equipment and receiver. -Reorient or relocate the receiving antenna.