User's Manual

ManualsBrandsEssel-T ManualsElectronicsREMOVU Motor Stabilizer

5. Calibration of Gimbal

1. Place the GoPro camera into frame housing and attach frame

housing to the gimbal.

4. After indicating "User Calibration" on OLED display, calibarion

operates for 5 second. (While operating calibration, DO NOT

move the gimbal and the frame housing.)

2. Put the frame housing on a at surface. (Refer to the image)

3. - Like the left image, hold the gimbal and the frame housing

tightly with hands.

- Power on the gimbal.

- Press the button and button together for 3 seconds.

(Please do calibration in a at or horizontal surfaces.)

Please do calibration when the S1 is not working as horizontal by unbalanced of roll

and tilt while using the S1.

Step 1 Step 2

Video Tutorials

Summary of content (9 pages)

PAGE 1
5. Calibration of Gimbal Please do calibration when the S1 is not working as horizontal by unbalanced of roll and tilt while using the S1. 1. P lace the GoPro camera into frame housing and attach frame housing to the gimbal. 2. Put the frame housing on a flat surface. (Refer to the image) 3. - Like the left image, hold the gimbal and the frame housing tightly with hands. - Power on the gimbal. - Press the button and button together for 3 seconds.
PAGE 2
6. How to use Low Angle When using Pan Mode: When using Follow Mode: In Pan Mode, the camera will automatically position left and right. The Tilt and Roll positions are fixed, therefore the camera will be pointing at the gimbal's motor. In follow mode, the camera will automatically adjust its position as it is inverted. Using your hand, manually adjust the camera's position by rotating the camera away from the gimbal motor. The gimbal is automatically position and ready for use.
PAGE 3
7. Firmware Upgrade Please visit our website at www.removu.com/s1_firmware. The detailed upgrade instructions can also be found on the page. Note: The USB port of this device is using as debugging port. so, consumers can not be used that USB as transmitting of data. 8. Technical Specs Gimbal Operating Voltage (DC) 6.4V ~ 8.4V Weight 380g (housing and battery excluded) Vertical Tilt Angle 292° Roll Angle 90° Horizontal Panning Angle 292° Operating Time (@25°C) 3h ~ 5h Battery 7.
PAGE 4
9. Safety Instructions Maintenance Follow these guidelines to get the best performance from your REMOVU S1. -R EMOVU S1 is a rainproof gimbal that can be used in the rain or snow. Do not submerge S1 in the water for underwater shoot purpose. Make sure that S1's battery cover is closed before using. - Before closing the doors, be sure the seals are free of debris. If needed, clean with a cloth. -B efore opening the doors, be sure S1 gimbal is free of water or debris.
PAGE 5
Battery Warning - Do not expose the battery to sunlight, fire or heat. - Do not disassemble, open or cut the battery. - Do not store the battery in high-temperature area. - Be careful of a short circuit of the battery socket. Do not store in a box or drawer in which there are other metal materials or coins. It might cause a short circuit. - Do not remove the packing of the battery before using. - Do not pressure any physical shock into the battery.
PAGE 6
10. Warranty Information Refund and Replacement Policy Essel-T Co., LTD. ("Essel-T") guarantees refund and replacement as the following conditions. -R efund can be requested within 7 days of the delivery date (subject to actual date the product was received) -R eplacement can be requested within 14 days of delivery date (subject to actual date the product was received) Please contact REMOVU Support Team or the authorized distributor of REMOVU from whom you purchased your product for more details.
PAGE 7
Warranty Service Essel-T Co., LTD. ("Essel-T") warrants that Essel-T's devices and accessories ("Products") are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase by the first consumer purchaser and continuing for 1 year period of time after that date. If the problem is not covered under the Essel-T Warranty Service, you may have to pay for the cost of return delivery and testing the product.
PAGE 8
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 9
www.removu.com Made for GoPro® HERO Cameras Copyright 2016 Essel-T Co., Ltd. All rights reserved. REMOVU® is a trademark of Essel-T Co., Ltd. registered in the U.S. and other countries. GoPro is a trademark of GoPro Inc. registered in the U.S. and other countries.