User's Manual

Note:
Thank you for your acquisition of this compact power bank wireless
charger, compatible with all Qi devices like Samsung S7/S7 edge,
Samsung S8/S8 edge, iPhone8, iPhone8 Plus, iPhone X, etc.
For optimum performance and safety, please read this manual
carefully before using this product.
Specification:
Capacity:10000mAh
Cell: Li-Polymer, Grade A
Transmission Distance: ≤6mm
Charging Efficiency: ≥70%
Size: 129.8*70.9*16mm
Weight:205g
Input Voltage: Micro: 5V/2A ,9V/2A ; Type C : 5V/2.5A,9V/2A
Output Voltage: 5V/3.1A, 9V/2A,12V/1.5A
Wireless Output Voltage: 5V/1A; 9V/1.12A
Wireless Power: 10W/7.5W/5W
Transmitter Coil Area
Wireless Charging Status Indicator
Switch
Power Level Indicator
Micro Input
Type-C Input/Output
USB Output
How to Use
Charging your Wireless Power Bank
1.Insert USB cable USB A end into power device.
2.Plug power device into DC power socket.
3.Plug the MIC end of the Micro USB data cable into the Input port of
the product. The blue light flashes to indicate the current power level.
Remark: please use the adapter & data cable could support QC 2.0 at
least if max output required
User Manual
Wireless Power Bank
Accessories:
Wireless Power Bank*1
Micro USB Charging Cable*1
User Manual*1
5
6
1.Make sure there is no any clutters on the
product.
2.Click the switch and the red light is on,
indicating wireless charging standby to
charge the terminal such as a mobile
phone.
3.Place a mobile phone or other
compatible device that complies with the
Qi protocol on the mobile power supply to
achieve wireless charging. Note that the
center of the mobile phone's receiving coil
must coincide with the transmitting coil of
the product, and the green light indicates
wireless charging.
When your wireless power bank works improperly
1.Make sure there is no any clutters on the wireless transmitter.
2.When the wireless power bank is over-heating, take your mobile
device away from your wireless power bank. And the transmitter will
stop charging automatically when over-heating. Please try charging
again when the wireless power bank cooling down.
Remarks
It’s normal that this charger and your smart phone will be hot under
operating conditions, and it may be more hotter when charging and
using at the same time (such as looping music)
USB port Schematic for regular charging and discharging
1.Insert the USB data cable USB A end into Output.
2.Plug the other end of the cable into a terminal such as a mobile
phone.
3.Click the switch button and the power is discharged to charge the
terminal such as a mobile phone and the blue light flashes. The red
light is on, indicating wireless charging standby.
Charging Your Device
Wireless discharging
Input
Output
0%-25%
1
25%-50%
2
50%-75%
3
75%-100%
4
Battery Indicator
Blue light flashes: charging
Blue light on: discharging
3
4
2
7
1
Red light on: wireless charging stand-by
Green light on: wireless charging
Red and blue light fast blink: abnormal operation
Indicators:
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
o
Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
The device has been evaluated to meet general
RF exposure requirement. The device can be
used in portable exposure condition without restriction.