ES710 User Manual ES710 User Manual R1.1 Author Revision Changes Date Changyu 1.1 Initial version 2015‐03‐03 Confidential Material: This document contains information that is proprietary and confidential, reading and copying this document is prohibited without permission from Asiatelco Technologies Co. Asiatelco Technologies Co.
ES710 User Manual Contents 1 Introduction .............................................................................................................................. 3 ID and Tooling Design ........................................................................................................................ 4 2 Hardware Design ....................................................................................................................... 5 2.1 Basic Hardware.....................................
ES710 User Manual 1 Introduction The ES710 is a self‐contained vehicle tracking device that combines GPS location with CDMA connectivity. Logically, the ION appears to a user or a server application as a single endpoint device. It can be queried, updated and configured either through a serial connection, or an over the air CDMA IP connection, or through SMS messaging. The ES710 presents itself over these connections as an enhanced cellular modem with attached functional elements.
ES710 User Manual ID and Tooling Design The housing will be provided by customer. The product appearance is shown as follows: Item Definition Dimension 83( L )*44( W )*17.7( H )mm Weight / FCC ID: YR8ES710 Asiatelco Technologies Co.
ES710 User Manual 2 Hardware Design 2.1 Basic Hardware Items Requirement Baseband Chipset VIA CBP8.
ES710 User Manual LED Red Function GPS Status On: GPS satellites acquired and Locked Flash Slow: GPS satellite search is in progress Off: No power or GPS subsystem fault Green CDMA/CDMA Connection On: Indicates CDMA connection is made Flash Slow: CDMA subsystem initialized but no connection Flash Fast: CDMA initialization in process Off: No power or CDMA subsystem fault The ION provides user control allowing the LEDs to be extinguished once installation is verified.
ES710 User Manual Antenna Loss <= ‐3 dB RX receive sensitivity conducted – TIS Board RF Specification Cellular Band RX Frequency range 869MHz～894MHz Sensitivity ‐108dBm (FER≤0.5%) Dynamic range ‐25～‐108dBm (FER≤0.5%) Single tone Desensitization ‐102.4dBm(FER≤1%,‐30dBm@±900KHz) Intermediation Spurious Response Attenuation Conducted Spurious Emission ‐102.4dBm(FER≤1%,‐43dBm@±900 KHz/±1700KHz) ‐91.4dBm(FER≤1%,‐32dBm @±900 KHz/±1700KHz) ‐80.
ES710 User Manual PCS Band RX Frequency range 1930MHz ~ 1990MHz Sensitivity ‐108dBm (FER≤0.5%) Dynamic range ‐25 ~ ‐108dBm (FER≤0.5%) Single tone Desensitization ‐102.4dBm(FER≤1%,‐40dBm@±1250KHz) Intermediation Spurious Response Attenuation ‐102.
ES710 User Manual tracking Sensitivity (UHIS): Sensitivity Tracking: -156dBm Reacquisition: -153dBm Acquisition: -144dBm Acquisition time: Hot: <2s Tracking Time Requirement Warm: <30s Cold: <60s Reacquisition: 2s - 10s Depends on signal level 2.3 Certification and Safety Items Requirement Drop Design 1.
ES710 User Manual 3 Software Features 3.1 Basic Software Items Requirement Air Interface CDMA 2000 1x 800/1900MHz; GPS 1x Data Supported IP Stack Upgrade Method RUIM Ipv4/IPV6 Remote update / PC tool Optional Compatible with None‐RUIM Supported Remote Update Supported Power Modes Supported AT Command Supported Report Supported；3000records Driver GPIO，LED，GPS，UART GPIOs Interrupt for Door Open Detect, Ignition Status LEDs GPS Status, CDMA Status Watch Dog Supported (CBP8.
ES710 User Manual Power cycle Watchdog timeout Reset command CDMA phone call reset SMS or UART power mode command Motion detect (if detector installed and enabled) When in a power down mode, the following resources will cause interrupts that will wake the ES710 and cause it to attempt complete the function associated with the interrupt. Simultaneous interrupts will cause sequential completion of each associated function.
ES710 User Manual and removed before it is transmitted. 4. Every report has a tag and each enabled interrupt or event generates a separate report. The report tags indicate the cause of the generated report, which can be an interrupt, an event or in response to a command. 3.6 Reset There is an internal soft reset. 3.6.1 Context Preservation When a reset is caused by the Network Watchdog or by the Reset command (modes 0,1), the context of the system is being preserved and is restored after the reset.
ES710 User Manual 4 Test Method 4.1 Hardware Test Item Description Baseband Function Test • • • • • • • • • • Power Input Test Power Consumption and Current Test Heat Dissipation Test UART Stability Test GPIO Level Test LED Stability Test Drop Down Test ESD Test High/Low Temperature Test Humidity Test RF Test • • • RF Performance Test GPS Performance Test Antenna Performance Test 4.2 Software Test Test Environment Construct message Test environment 1.usb dongle and PC as message server 2.
ES710 User Manual 5 FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
