ESKY WIRELESS INC. ES310 User Manual V1.
Information to User This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
warning The device has been evaluated to meet general RF exposure requirement. This device should be installed in where that has no emission source and no metallic object obscures. RF Exposure Compliance The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or Transmitter.
Catalogue Version history .................................................................................................................................. 5 1. Structure Introduction .................................................................................................................. 6 2. Preparation.................................................................................................................................... 7 3. Quick Using Steps ........................................
Version history Version Data Note Author V1.0 2013-10-1 First version Apple V1.1 2013-10-8 V1.2 2013-10-11 Jane Add chapter 3.6.
1. Structure Introduction ① ② ③ ④ ES310 works with power line and I/O line USB port Supply power port and I/O port Dimension: 83mm*43.2mm*17.
2. Preparation Make sure the equipments below are all available.
3.
3.1 Step 1: Insert SIM Card Open the terminal cover, and put the metal side of SIM card face down and then fasten the card slot cover. Note: SIM Hot-Plug is forbidden for this device. 1. Metal side faces 2. Fasten card slot 3.2 Step 2: Install ES310 The terminal is GPS positioning product, it is recommended that you follow the instructions to install.
① ② ③ I/O line Power supply line ④ 3.2.1 Connect Lines to ES310 First, connect power supply line to ES310.
Plug the part ④ of power supply line into ES310 power supply port (chapter 1 ③) 3.2.2 Connect ES310 to the Vehicle Power lines, it can connect with cigarette lighter or OBD I/O line, connects terminal with the I/O connector of wire harness. For the detailed description, please refer to chapter 4. 3.3 Step 3: Power On When finishing installation, as long as power supply line is connected with cigarette lighter or OBD, ES310 is powered on and starts work.
When ES310 is powered on, the two LEDs –Yellow and green LEDs will light for 10 seconds; then, only green LED will blink four times; after blinking, yellow and green LEDs will blink together. Wait for a while, yellow LED will light without blink. The meaning of each LED means, please refer to chapter 5.1. If not, your situation is: 1) No LED lights Please check the way you power on or the voltage that power supplies. 2) Only green LED lights Please make sure that SIM card is inserted.
Note: It’s also no problem if the user name and the pass word are not set. For example (the content of SMS): gprs,cmnet, www.eskylocate.com:1750# Report server URL APN The possible responses: ①GPRS=Success! That means everything goes well. GO TO Step 5. ②GPRS=Fail! Make sure no parameters are missed. ③No Response. Make sure your phone number has bound before. Make sure GPRS spelling correct. No space in the beginning. Make sure ending character’#’. No space in the end.
Make sure ES310 is in the open air Make sure GPS signal coverage is good. 3.5 Step 5: Query Current Location (SMS) If Step1 ~ Step 4 have passed, Then you can refer to to go on test other functions. The Query Current Location command is “Where, [PASSWORD] #”. For example: The content of SMS should be: Where, 000000# The possible responses: ① WHERE=31.86384+120.92707+10.74468! If the reply SMS contains latitude, longitude and speed. It means that ES310 has GPS fixed.
Figure 1: Loading Page If you don’t see this page, please do: ①Check your Internet Connection. ②Check your operation system(No IOS). ③You don’t have install plug-in (sliverlight), Microsoft will give you the link of installation. If not, you have to install it by yourself: http://www.microsoft.com/getsilverlight/Get-Started/Install/Default.aspx 3.6.2 Login Page After finish loading, go into Log-In page. If the language of this log-in page is Chinese, please change the language.
Figure 2: Chinese Log-In Page Figure 3 shows the English Log-In page. Now click “Not a member yet? Take a minute to sign up” to register an account. Figure 3: English Log-In Page 3.6.3 Register an Account Fill up all the items as shown in Figure 4. Without any error hints, click “Confirm”. Notes: ①Make sure IMEI is the exactly number you can see on the product label. Totally 15 numbers. And also it’s unique, so don’t register with using same IMEI. ②Table “Version”, please choose ES310.
Figure 4: Register Pop-up After register successfully, return to Log-In page and enter the User Name and Password you just set. 3.6.4 Default Account for User eSky Wireless Inc. has an default account for user to experience the Car Online Platform. The default account: User name: esky Password: esky1233456 You are welcome to use the above user name and password to register on our platform.
3.6.5 Start Tracking When you see the page like Figure 5, Congratulation! Now you can start tracking. Figure 5: Main tracking Page 3.6.6 Modes Switch Page If you have two or more ES310 devices, you can add the others in one account (Same UserID). Click the middle of 3*3 squared. As shown in Figure 6. Figure 6: Modes Switch Page Then click “Add” button, a new form will pop up shown in Figure 7. Enter new device’s information like register. Click “Confirm” to finish adding.
Figure 7: Add Device Pop-up
If commands are set by AT command, please refer to to install ES310 device driver and set hyper terminal. You can contact our technical support to ask for device driver and . If everything is ready, then follow me to enjoy the AT command trip. 3.7 Step 7: Set APN, Report Server IP (AT) Note: AT command is based on the command in . If you are not in China or America, APN is necessary to change. The command to re-set APN and server IP is “GPRS”.
Note: Do not forget the ENTER at the end of command. The possible response: ① OK GPRS=Success! It means APN, server IP have changed successfully. ② OK GPRS=Fail! Try again Please don’t set any command within 1 ~ 2 min after ES310 is powered on. Mark sure GPRS command spells correctly. ③ ERROR Make sure that AT command mark spells correctly. ④No response. Type “enter” again. Re-type GPRS command again without pause. 3.
AT command should be: at*cmd=”interval,000000,120#” Possible Response: ① OK INTE RVA L =Success! ② OK INTERVAL=Fail! ③ ERROR ④No Response.
4. Install and Operation 4.1 Installation Method Note: 1) The following installation order, please do not inverted. 2) During the installation process, please do not supply the terminal. The terminal installation is divided into hidden installation and open installation. When the terminal is using special vehicles, hidden installation is recommended. Otherwise, open installation is chosen. (To avoid thieves’ damage, the installation location should be hidden) 4.
4.3 Installation Notes ① Avoid put together with the emission source, for example, reversing radar, anti-theft devices and other on-board communications equipment. ② As for fixing the terminal, you can bound with ties or stick with wide sponge strength double-faced adhesive. ③ The terminal has GSM antenna and GPS antenna，so the installation should ensure that the ES310face up (that is GPS toward the sky). Besides, there is no on-metallic object that obscures above the terminal.
5. Supplement 5.1 LED Indication Yellow LED indicates GPRS status. Green LED indicates GPS status. Power ON Power OFF GPS Searching GPS Fix GREEN On 10-15sec Blink On YELLOW On 10-15sec See ** See ** **: When server is connected, the yellow light will on. When PDP is activated but no server connection, the yellow will blink every second. But if PDP cannot be activated, it shows off. 5.2 I/O Harness ES310 has 3 INPUTs, 2 OUTPUTs.
