User's Manual

b) Controller (Top View)
c) Receiver
d) Headset / Earphone
Battery Replacement:
a) Open the battery compartment door.
Note:
The controller and the receiver must be connected before assigning a Turbo Fire
to any of the action buttons.
The Turbo LED will remain lit when any button has Turbo Fire assigned to it.
To Clear a Turbo assigned button:
1) Press and hold the Clear button, the Clear LED lights up.
2) Press the button which has been set to Turbo Fire, the Turbo LED turns off.
The Turbo Fire of the button is now clear. Repeat this procedure for any other
Turbo Fire cancellation.
Low Power Indication:
The controller’s LED starts to blink 2 times per second when the power is low.
When this occurs, replace all your batteries with new ones.
For technical assistance please visit our website: www.hipgearproducts.com
6. a) Wear the headset as shown in figure1:
6. b) Adjust the bendable hook of the headset to custom fit securly around your
ear as shown in figure 2:
6. c) Adjust the microphone as shown in figure 3 as close to your mouth as possible
to achieve the best sound quality.
7) Adjust the volume accordingly.
When activating the on-line function
of the XB-Comm you must be within
1~2 meters (roughly 3~6 ft.) of your
console to ensure a strong signal.
Press and hold the on-line button for
3 seconds (the LED will turn green).
Once you are connected, you can then
move away from your console. Please
see the manual for further instruction
on proper use of your XB-Comm
controller.
Y
X B
A
S
T
A
R
T
B
A
C
K
Y
X B
A
S
T
A
R
T
B
A
C
K
C
L
E
A
R
T
U
R
B
O
LED light-up
3) Slide the power switch to the ON position on the controller. The controller’ s
LED will also start to blink. The LED of the controller and the LED of the
receiver will stop blinking when the connection has been completed.
4) If you want to play your game with vibration feedback, place the power
switch into the vibration position.
5) Plug the headset / earpiece into the earphone jack of the controller and
place the earpiece around either ear.
How to use Hip Gear Headset:
To achieve the best voice communication and headset comfort when using your
XB-Comm on-line, follow all the instructions outlined in this manual about adjusting
the headset.
b) Place the batteries into the controller (as marked
on the bottom of the battery compartment).
c) Close the battery compartment door.
You are now ready to use your XB-Comm
TM
Bluetooth
®
Xbox
®
Wireless
Controller & Headset.
Note:
- For longer playing time, always use Alkaline batteries.
- Do not mix new and used batteries, this will reduce the controller’s transmitting
and receiving distance and may cause the product to malfunction.
- Rechargeable batteries can be used with this product (rechargeable batteries
are not included).
- Dispose of used batteries according to the battery manufacturer’s instructions.
How to Use:
1) Turn on the power of the Xbox
®
console.
2) Plug the receiver into the first controller slot of the Xbox
®
console. The
LED of the receiver will start to blink.
Note: Do not plug more than one receiver into the console at the same time. You
must wait until the first receiver has been connected to its controller before
you plug in any other receivers; otherwise, a malfunction may occur.
Thank you for purchasing Hip Gear’s XB-Comm
TM
Bluetooth
®
Xbox
®
Wireless
Controller & Headset for the Xbox
®
Console. Please read this instruction manual
thoroughly before use.
Features:
- Fully compatible with Xbox
®
& Xbox Live
TM
.
- Bluetooth
®
Wireless Technology to ensure maximum signal strength
- Auto channel scanning
- Light weight headset with microphone for On-Line gaming
- Turbo Fire
- Dual Vibration Feedback motors
- Low Battery Warning Indicator
- Super long play time – up to 50 hours (with vibration deactivated)
- Twin rubberized analog sticks and fully analog action buttons for precise control
- Rubberized grips to ensure comfort and prevent slipping during game play
- Optimal transmitting and receiving performance at 30ft. (10 meters) or less
Button Configurations:
a) Controller (Front View)
Hip Gear XB-Comm
TM
Bluetooth
®
Xbox
®
Wireless Controller & Headset
Y
X
A
B
Black
White
LT
Back
Start
D-PAD
RT
Turbo
Clear
Off/On/Vibration
Volume Adjustment
Phone Jack
L-Trigger
R-Trigger
Memory card slot
Connection LED Indication
How to Connect the Controller for On-Line Gaming:
Press and hold the “on-line” button on the controller until the button’s LED turns
green. You are now ready for on-line gaming!
Mute Function:
The mute function allows you to disable your microphone so your opponent cannot
hear you speak while you are gaming on-line. While your microphone has been
muted you will still be able to hear your opponent.
To use the on-line mute function, simply press the controller’s “on-line” button once.
The button’s LED will change from green to red. The mute function has now been
activated. To deactivate the mute function, press the “on-line” button again. The
button’s LED will change from red to green. The microphone will now be on.
How to Deactivate the On-Line Function of the Controller:
Press and hold the “on-line” button for 3 seconds. The green LED will go out and
the on-line function of the controller will be deactivated. The controller can now
only be used as a regular wireless Xbox controller. To reactivate the on-line
function, press and hold the button until the button’s LED once again turns green.
Note:
It is recommended that you deactivate the on-line function when it is not in use.
This will extend the life of the controller’s batteries.
Turbo Fire Setting:
Each action button of the controller has a built-in Turbo Fire Function. Simply follow
the steps listed below to activate Turbo Fire:
1) Press and hold the Turbo button, the Turbo LED lights up.
2) Press the action button you wish to assign a Turbo Fire Function to. The
Turbo LED will blink when the setting is successful.
3) The Turbo LED blinks rapidly whenever the assigned Turbo Fire button is
pressed.
4) Repeat the procedure to assign another button for Turbo Fire Function.
POWER LED
RT
POWER ON
OFF ON
VIBRATION
OFFON
Volume Adjustment
Y
X B
A
S
T
A
R
T
B
A
C
K
C
L
E
A
R
Y
X B
A
S
T
A
R
T
B
A
C
K
T
U
R
B
O
C
L
E
A
R
LED light-up
RT
POWER LED
Microphone
Phone Jack
NOTE: The speaker of
the headset moves up
and down to ensure a
snug and comfortable
fit to your ear.
TM
TM
On-line Button
RT
CAUTIONS: XB-Comm uses Bluetooth Wireless Technology which operates on
the 2.4GHz radio frequency band. This RF band is also used by many cordless
telephones, wireless home networks and even microwave ovens. Operation of the
XB-Comm controller in close proximity to any of these devices may result in interference
and noise in the earpiece of the headset. Moving the receiver and/or console further
away from the interfering device may solve this problem.
XB-Comm features an industry standard 2.5mm headset jack, allowing you to use
any wired headset with a standard 2.5mm plug. Please note that only the included
headset is covered by the Hip Gear warranty.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
There is no guarantee that some form of interference will not occur in a particular
installation.
If this equipment does cause interference to radio or television reception, the user
is encouraged to try one or more of the following corrective measures:
a) Reorient or relocate the receiving antenna;
b) Increase the separation between the equipment and receiver;
c) Connect the equipment into an outlet on a circuit different from that which the
receiver is connected to;
d) Consult an experienced radio/TV technician for assistance.
IMPORTANT NOTE: READ THIS FIRST!
Instruction Manual