User's Manual

ManualsBrandsEsel International ManualsElectronicsI-POD RECEIVER

WIRELESS MOBILE REMOTE KIT for iPod Item: 88030

Thank you for purchasing the Wireless Mobile Remote Kit, compatible for use with all full

size iPods. Please review the instructions below to ensure proper installation and use of

this product.

INSTALLATION

STEERING WHEEL MOUNT

Your Wireless Mobile Remote Kit includes a unique mount designed to attach to the inside

of your carÕs steering wheel, enabling you to control your iPod without removing your

hands from the steering wheel. The Steering Wheel Mount is adjustable to attach securely

to most common automobile steering wheels. Additional cushion pads are included for

custom mounting to smaller diameter steering wheels.

To attach the Steering Wheel Mount:

1. Begin by unscrewing the centrally located hex screw. Please use the included Wheel

Mount Adjustment Tool (Diagram 1).

2. Once the screw is loosened you can place the mount at a preferred position on your

steering wheel with the circular Remote Control Unit cavity facing the driver. We

recommend a location that does not conflict with your normal grasp of the steering wheel.

IMPORTANT: The Steering Wheel Mount should be attached so that the Wireless Remote

Unit is positioned on the steering wheelÕs INSIDE ONLY (Diagram 2).

3. Once you have selected the desired position on the steering wheel, tighten the mount

screw using the included Wheel Mount Adjustment Tool.

NOTE: If the screw has been fully tightened but the diameter of your steering wheel is too

small to hold the mount properly, you will need to use one or more of the included cushion

pads. Return to Step #1 and add one or two cushion pads to the inside of the Steering

Wheel Mount as required to securely attach the mount to the steering wheel (Diagram 3).

4. Press the Remote Control Unit into the circular cavity on the Steering Wheel Mount until it

clicks into place. The Remote Control Unit will rotate so that the buttons are aligned to

the mountÕs position on the steering wheel (Diagram 4).

5. To remove the Remote Control Unit, simultaneously press the two buttons on opposite

sides of the mount.

NOTE: Store the Wheel Mount Adjustment Tool in a safe location for future use.

Attaching the Wireless Remote Receiver to your iPod:

In order to control the iPod using the Remote Control Unit you will need to attach the

included Wireless Remote Receiver to the top of your iPod. With the Nyko logo facing in the

same direction as the front of the iPod, gently press the Receiver unit down into the iPodÕs

headphone and remote jacks (Diagram 5).

IMPORTANT: When attaching the Wireless Remote Receiver, do NOT use force.

The receiver is designed attach easily to the iPod. No force is necessary.

WIRELESS REMOTE FUNCTION AND FEATURES:

PLAY / PAUSE BUTTON: Press this button to Play or Pause the current track. Holding this

button down for 4 seconds turns the iPod power OFF (or ON if the iPod is OFF).

PLUS (+) BUTTON: Press this button to raise the volume of the iPod headphone jack

output.

NOTE: Volume buttons do not control the volume of the Dock Connector audio output,

which is preset and cannot be adjusted.

MINUS (-) BUTTON: Press this button to lower the volume of your iPodÕs headphone jack

output. Please note that volume buttons cannot adjust the volume of the Dock Connector

audio output. The Audio output of your iPodÕs Dock Connector is set at a preset level and

cannot be adjusted.

TRACK FORWARD (>1) BUTTON: Press this button once to advance to the next track.

Holding this button down will fast forward through the current track.

LAST TRACK (1<) BUTTON: Press this button once to go to the beginning of the current

track. Press the button twice quickly to go to the previous track in your play list. Holding this

button down rewinds through the current tack.

REMOTE WRISTBAND ADAPTOR

The Wireless Mobile Remote Kit can be used outside of the car as well. The included

Wristband Remote Adaptor enables you to control your iPod while jogging, bicycling, or

anywhere on the go.

Attaching the Wireless Remote Unit to the Wristband Adaptor:

The Wireless Remote Unit attaches to the Wristband Remote Adaptor by two lock tabs

located on the surface of the wristband (Diagram 6).

1. Align the two openings on the underside of the remote with the tabs on the wristband.

2. Gently twist the remote counter clockwise to lock the remote onto the Wristband Adaptor.

3. To remove the remote from the Wristband Adaptor, gently twist the remote clockwise a

short distance until the tabs align with openings so that the remote can be pulled free

NOTE: When attaching or removing the Wireless Remote Unit, no force is necessary.

The unit is designed to attach and detach easily from the adaptor.

USING THE CASSETTE ADAPTOR

If your car stereo features a compatible cassette tape player, you can use the included

Cassette Adaptor to play your iPod music through your carÕs stereo system.

IMPORTANT: Use only if the car cassette player supports this type of cassette adaptor.

In general, stereos with side-loading cassette tapes that leave the edge of the tape visible

while playing are compatible with this device. If the cassette player in your car draws the

cassette in and has a mechanical gate that must close fully during play, we do not

recommend using this adaptor. If you have any question regarding the compatibility of the

Cassette Adaptor with your car stereo, consult the manufacturer of the car stereo system.

1. Insert the plug at the end of the Cassette AdaptorÕs cable into the headphone jack

located on top of the Wireless Remote Receiver.

2. Measure the distance from the cassette player to the iPod mount, and fold and tie up the

excess cable using the attached Velcro wrap.

3. Insert the Cassette Adaptor into the player with the cable end pointing towards you,

outside of the cassette player.

4. Once the Cassette Adaptor is properly inserted into the player, play the cassette to

activate your iPod. The iPod playback should be audible through the cassette mode of

your stereo.

5. To stop playback, stop your iPod and/or press the eject button on the cassette player.

Careful use of the device insures a long life for your new accessory. Please be cautious

while driving, and focus on the road.

INSTALLING THE UNIVERSAL CAR MOUNT (Diagram 7)

WARNING: For your safety, we recommend that you only access the iPod controls when

your automobile is not in motion. Please keep your eyes on the road!

USING THE AIR VENT MOUNT

The vent clips allow for attachment to either vertical or horizontal blades of your dashboard

air vents.

1. Attach the vent mounting plate (A) to the back of the Universal Car Mount.

2. Insert the vent clips (B) into the bottom center of the mounting plate, making sure they

are oriented to match the direction of the air vent blades. Then slide them into the rails to

the extreme left and right of the mounting plate.

3. Gently insert the vent clips onto the blades of the vent. Never use excessive force in

attaching or removing the vent clips.

4. Make sure that the vent clips are spread evenly to each side for optimal weight distribution.

IMPORTANT NOTE: You should restrict hot or cool air flow to the vent holding the Universal

Car Mount and iPod by disabling that air vent. Excessive temperatures can cause serious

damage to your Universal Car Mount and iPod. Refer to your automobile ownerÕs manual

for instructions on controlling air flow to individual air vents.

USING THE STICKER MOUNT

The Sticker Mount is a permanent solution that requires the adhesive mounting plate (C) to

be attached directly to a surface in your car with an adhesive material.

It is essential to remove any dirt, polish or conditioners Ð which can impair adhesion Ð from

the area to receive the adhesive mounting plate. Consult with your car manufacturer as to

which products to use for this purpose.

Once you have determined the location on your dashboard or console, double-check the

orientation of the adhesive mounting plate before removing the protective paper, making sure

the Universal Car Mount will slide DOWNWARDS into the plate. Once the adhesive mounting

plate has been attached, leave it in place for approximately 12 hours prior to first use.

IMPORTANT: Removing this adhesive mounting plate may cause damage to your dash-

board material. For this reason be very sure of the position before installing the adhesive

mounting plate. Nyko does not assume any responsibility for damage that may be caused

by removing the adhesive mounting plate after it has been attached.

MOUNTING A FULL SIZE IPOD

1. Make sure that the Universal Car Mount arms (D) are in the open position by pressing the

release button (E) located on top.

2. Place the iPod into the Universal Car Mount and gently push it back against the spring-

loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod, simply press the release button on the top of the Universal Car Mount.

MOUNTING THE IPOD MINI

1. Make sure that the Universal Car Mount arms are in the OPEN position.

2. Align the iPod mini to the guides at the inside bottom center of the base. Gently push it

back against the spring-loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod mini, simply press the release button on the top of the Universal

Car Mount.

Universal Car Mount and iPod by disabling that air vent. Excessive temperatures can cause

serious damage to your Universal Car Mount and iPod. Refer to your automobile ownerÕs

manual for instructions on controlling air flow to individual air vents.

USING THE STICKER MOUNT

The Sticker Mount is a permanent solution that requires the adhesive mounting plate (C) to

be attached directly to a surface in your car with an adhesive material.

It is essential to remove any dirt, polish or conditioners Ð which can impair adhesion Ð from

the area to receive the adhesive mounting plate. Consult with your car manufacturer as to

which products to use for this purpose.

Once you have determined the location on your dashboard or console, double-check the

orientation of the adhesive mounting plate before removing the protective paper, making

sure the Universal Car Mount will slide DOWNWARDS into the plate. Once the adhesive

mounting plate has been attached, leave it in place for approximately 12 hours prior to first use.

IMPORTANT: Removing this adhesive mounting plate may cause damage to your dash-

board material. For this reason be very sure of the position before installing the adhesive

mounting plate. Nyko does not assume any responsibility for damage that may be caused

by removing the adhesive mounting plate after it has been attached.

MOUNTING A FULL SIZE IPOD

1. Make sure that the Universal Car Mount arms (D) are in the open position by pressing the

release button (E) located on top.

2. Place the iPod into the Universal Car Mount and gently push it back against the spring-

loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod, simply press the release button on the top of the Universal Car Mount.

MOUNTING THE IPOD MINI

1. Make sure that the Universal Car Mount arms are in the OPEN position.

2. Align the iPod mini to the guides at the inside bottom center of the base. Gently push it

back against the spring-loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod mini, simply press the release button on the top of the Universal

Car Mount.

USING THE STICKER MOUNT

The Sticker Mount is a permanent solution that requires the adhesive mounting plate (C) to

be attached directly to a surface in your car with an adhesive material.

It is essential to remove any dirt, polish or conditioners Ð which can impair adhesion Ð from

the area to receive the adhesive mounting plate. Consult with your car manufacturer as to

which products to use for this purpose.

Once you have determined the location on your dashboard or console, double-check the

orientation of the adhesive mounting plate before removing the protective paper, making

sure the Universal Car Mount will slide DOWNWARDS into the plate. Once the adhesive

mounting plate has been attached, leave it in place for approximately 12 hours prior to

first use.

IMPORTANT: Removing this adhesive mounting plate may cause damage to your

dashboard material. For this reason be very sure of the position before installing the

adhesive mounting plate. Nyko does not assume any responsibility for damage that may be

caused by removing the adhesive mounting plate after it has been attached.

MOUNTING A FULL SIZE IPOD

1. Make sure that the Universal Car Mount arms (D) are in the open position by pressing the

release button (E) located on top.

2. Place the iPod into the Universal Car Mount and gently push it back against the spring-

loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod, simply press the release button on the top of the Universal Car Mount.

MOUNTING THE IPOD MINI

1. Make sure that the Universal Car Mount arms are in the OPEN position.

2. Align the iPod mini to the guides at the inside bottom center of the base. Gently push it

back against the spring-loaded depth adjuster. Pull the arms together to lock onto the iPod.

3. To release the iPod mini, simply press the release button on the top of the Universal

Car Mount.

FCC Advisory

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTER-

FERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUD-

ING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFER-

ENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFI-

CATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

TECHNICAL SUPPORT

We appreciate your support of NYKO products, and endeavor to guarantee your

satisfaction with this product. If you experience difficulties, please contact us.

Email: customersupport@nyko.com

Phone: 1-888-444-NYKO (6956)

NYKO Product Limited Warranty

This NYKO product is warranted to the original purchaser for the normal intended use for a period of

ninety (90) days from the date of purchase. If a defect covered under this warranty occurs, NYKO

will replace or repair the product or its defective parts, at its option, at no charge. Warranty does not

apply to defects resulting from modification or misuse of this product. The product can be returned to

the place of purchase accompanied with proof of purchase or shipped to: NYKO Technologies Inc.,

1990 Westwood Blvd, 3rd Floor, Los Angeles, CA 90025, with freight charges prepaid. Please allow

3-4 weeks for processing.

Diagram 1

Remote Steering Wheel Mount

Diagram 3

Remote Steering Wheel Mount w/pads

Diagram 4

Installing Remote into Steering Wheel Mount

Wheel Mount

Adjusting Tool

Correct

Position

Wrong Position

Wheel Mount Pads

Diagram 5

Attaching Wireless Remote Receiver to iPod

Diagram 7

Installing Universal Car Mount

vent mounting plate

adhesive mounting plate

air vent clips

Diagram 6

Attaching Wireless Remote Receiver to Wristband

Top

Bottom

Top View

Diagram 2

Remote Steering Wheel Mount Positioned on Steering Wheel

Item# 88030

for/pour/para iPod

www.nyko.com

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

Nyko

and Wireless Mobile Remote Kit

are trademarks of Nyko Technologies, Inc.

FRONT

Nyko Technologies, Inc. -- Item # 88030 -- "Wireless Mobile Remote Kit" for iPod -- Instruction Manual BACK (French/Spanish) -- Version 1 -- May 25, 2005