Shower Door Installation Instructions Left-hand door installation shown Right-hand door installation shown NOTE: This model is reversible for left or right-hand door installation. This manual will show the Left-hand door installation as an example throughout. For a Right-hand door installation, install both pivot bars with the holes on the correct side. See step #3 for details. A | Please Do Not Return the Product to the Store. | ~ Contact us with any questions.
‘throw SHOWER DOOR Verify threshold and wall with a level. 3/8” (10mm) Out-of-Plumb Adjustment within the Wall Profile.
SHOWER DOOR PACKAGE CONTENT Gog [eee PACKAGE CONTENT PART# DESCRIPTION QTY | PART# DESCRIPTION QTY A Pivot Bar 2 G Stationary Glass-L 1 B Bottom Anti-Water Strip | 1 H Wall Jamb 2 Cc Magnetic Strip 1 Glass Bracket 4 D Magnetic Strip 1 J Pivot 2 E Handle 1 K Stationary Glass-R 1 F Glass Door 1 L Anti-Water Strip 1 i“ ~ Inspect all parts for missing prior to installation! NOTE! Soh AL Contact us for any part missing.
SHOWER DOOR PACKAGE CONTENT CY aa RC Screw 7 pcs EE 7 pcs 7 pcs 7 pcs A Additional spare parts are included. Wall anchor Screw @6x28mm Screw cover ST4*10 mn ~ Inspect all parts for missing prior to installation! Note \ “A Contact us for any part missing.
TOOLS REQUIRED Drill Bits h Screw Driver | ( Drill hp Level h aN 21/8"& @1/4” (3& 6mm) dia.
SAFETY INFORMATION CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: » Always wear safety glasses and gloves while handling. » Always follow the installation instructions. * Inspect glass for damage before installation.
‘throw SHOWER DOOR Wall Jamb(H) Installation TABLE 1 Enclosure assembly measurements Measure from the finished corner to the inside edge of wall profile as shown: Model No. W1 W2 KJJSSD3672REQ1CH1 33 3/16" 33 3/16" Co NOTE ‘1. Mark the wall at the threshold A ot ng; according to the dimensions for 20° Ye the model size shown in Table 1 . WAN W Ung OF 2 Place the Wall Jamb (H) WN 2 against the walls and aligned with the new reference marks on the threshold. Use a level to plumb each wall profile.
SHOWER DOOR 2 3 | Drill the holes. See NOTE below. Fig 2 1. Make sure each Wall Jamb (H) is 2.1) 2. Mark the holes for drilling on the wall through the prevailed holes in the Wall Jamb 2.2) 3. Drill the 4. Run a bead of waterproof silicone along the back of the Wall Jamb (H) and around the holes in — the wall. (Fig 2.5) 5. Attach the Wall Jamb (H) to the wall using the Screws ST4.2x30 2.6) Stud is presented behind the wall: el drill pilot holes into the stud and 7 \ the ST4.0 x 30mm Screw NOTE ise e ST4.
Stationary Installation Insert each Stationary Glass (G&K) into the installed Wall Jamb (H) and check the panels for plumb.
‘throw SHOWER DOOR Pivot Bar (A) Installation Examine the Pivot Bar (A) and notice that there are holes for the top and bottom pivot assemblies on one end. (Fig 4b) Attach the top and bottom Pivot Bar (A) (with the pivot holes on the correct side for the swing of the door) through the holes in the Stationary Glass the clear Vinyl Gaskets of Glass Bracket (I) between the Pivot Bars and the Stationary Glass (G&K) to prevent glass-to-metal contact.
Pivot(J) Installation The pivot assemblies are paired: one rotates CW and one rotates CCW. Take note to install the Pivot Assemblies (J) to the top and bottom Pivot Bar (A) so that the door will swing out. 1. Attach the top and bottom Pivot (J) to the Pivot Bar (A) using the Hex Socket Bolts M8x12. (Fig 5.1) 2. Remove the bolts and plates from the Pivot the Glass Door (F) into the pivots so that the holes are aligned. Make sure the vinyl gaskets are in place between the glass and the metal plates. (Fig 5.
Stationary Installation ; 1. Make final adjustment by the adjustable wall profile so Rh that the door opening is square. (Fig 6.1 & 6.2) 2. Drill through the prevailed holes in the Wall Jamb (H) into Stammer the first layer of the Glass Profiles using an @1/8” drill bit. Pan Head Screw NOTE (Fig 6.3) Use the Screws ST4.2x10 (dd) and washers to secure © ) the Stationary inside the Wall Jamb (H). (Fig washer cap 6.386.4) L | 4. Cover the screws with the Screw Cover (cc). (Fig 6.
Strip Installation 1 ; 1. Push the Anti-water Strip (L) onto the pivot edge of oo the Glass Door(F) with the soft fin on the inside of the inside shower so that it overlaps the Panel Glass when the door is closed. (Fig 8.1) A NOY Note: The fin on the Bottom Anti-Water Strip (B) should Glass Door be installed toward the inside of the 8.2) 2. Cut the Bottom Anti-Water Strip (B) to fit from the bottom pivot to the strike edge of the Door Glass (F).
SHOWER DOOR VERN Ensure that the Shower door closes tightly and opens smoothly. NOTE Apply a good quality silicone sealant along the Wall Jamb (H) and Se Bottom Pivot Bar (A) . A Allow 24 hours for the silicone to cure before using the shower. Apply Silicone Sealant, (not supplied).