Installation Instructions

ManualsBrandsErkios Systems ManualsElectronicsLow Power Transmitter

**Trademark / US patent / customer service**

[Back Cover]

Fortifi EP-RJ45

Manual

DRAFT COPY [Front Cover]

FCC

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

FCC Note: The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modifications to this

equipment. Such modifications could void the user's authority to

operate the equipment.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Important note: To comply with FCC RF exposure compliance

requirements, no change to the antenna or the device is permitted.

Any change to the antenna or the device could result in the device

exceeding the RF exposure requirements and void user's authority to

operate the device.

FCC ID: 2ATONEPRJ45

Summary of content (5 pages)

PAGE 1
FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
PAGE 2
Introduction Warranty The EP-RJ45 port security device is designed to secure your in-use and unused RJ45 ports. SPECIFICATIONS CAUTION • We strongly recommend that installation is performed by a trained IT Technician. Model Number: EP-RJ45 • Read the enclosed instructions carefully before installing the new EP-RJ45 device.
PAGE 3
page 2 Place Holder Table of Contents: Introduction Page 1 Table of Contents Page 2 In-Use Cable Lock Installation Page 3 In-Use Port EP-RJ45 Installation Page 4 Unused Port EP-RJ45 Installation Page 5 Page holder Page 6 Page holder Page 7 Warranty and Specifications Page 8 FCC Back cover Page 7
PAGE 4
*** Check before Installation! *** • • • Place holder Is the network cable sheath locked inside the RJ45 housing? If it is loose, you may need to apply a small amount of CA glue into the RJ45 housing, and onto the sheath to prevent it from slipping out of the RJ45 housing. For secure installation, the sheath must be firmly locked into the RJ45 housing. In-use Cable Lock Installation • • • Place the upper cable lock onto the network cable and into the rear of the RJ45 housing.
PAGE 5
In-use Port EP-RJ45 Installation Unused Port EP-RJ45 Installation • Close the lid of the EP-RJ45 around the in-use network cable. • Insert the Unused port lock into the RJ45 port. • Push the EP-RJ45 device all the way forward towards the RJ45 port. You will hear a series of clicks as it locks on the the port. • Close the lid of the EP-RJ45 and install the EP-RJ45 device onto the Unused port lock. You will hear a series of clicks as it locks onto the port.