WCS band Radio Module WRM Product Manual 2.6 GHz WCS band Backhaul Radio Module FCC ID RAR20007001 Document Date: March 2007 Document Number: PM-B2XH068AA-A Document Version Number: 3 Document Status: Release © Copyright 2007 by BelAir Networks. All rights reserved..
WRM Product Manual – 2.6 GHz WCS Band Radio Module Contents About this Document.................................................................................................. 3 Introduction................................................................................................................. 3 Picture of the B2XH068AA-A 2.6 GHz WCS band Backhaul Radio.................... 4 General Conditions of Use .........................................................................................
WRM Product Manual – 2.6 GHz WCS Band Radio Module About this Document This document is a product manual for the B2XH068AA-A 2.6 GHz WCS band Backhaul Radio Module 1, FCC ID RAR 20007001. The manual outlines the radio modules limitations on use in BelAir Networks products marketed or offered for sale. An overview of BelAir Networks products is included with information on the module installation in these products.
WRM Product Manual – 2.6 GHz WCS Band Radio Module to provide last mile access for cellular backhaul applications. The WRM operates in the licensed 2.6 GHz frequency bands, and the added capacity that WiMAX (IEEE 802.16d) delivers to the network is ideal for critical applications such as voice traffic. Picture of the B2XH068AA-A 2.6 GHz WCS band Backhaul Radio Module is shown below for reference, notice that the connector interfaces only allow integration of the module into BelAir Networks products .
WRM Product Manual – 2.6 GHz WCS Band Radio Module General Conditions of Use This manual is intended to supplement training provided by BelAir Networks or authorized parties. The module B2XH068AA-A is only intended for use in BelAir Networks products and is not for sale to the general public as a stand-alone module. Please read this entire document, including the Regulatory Statements section before attempting to install or operate the module.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Overview of B2XH068AA-A module installation into BelAir Networks products List of Approved Final Products The B2XH068AA-A module is only approved for use in the following BelAir Networks products: • BelAir200. See BelAir200 documentation for complete manufacturing instructions. • BelAir100. See BelAir documentation for complete manufacturing instructions.
WRM Product Manual – 2.6 GHz WCS Band Radio Module B2XH068AA-A module installation into BA100 product The module can be installed into three variants of the BA100 product, namely the BA100, BA100C and BA100S. The BA100 product is capable of incorporating two radio modules, options include two B2XH068AA-A ( FCC ID :RAR20007001) modules or one B2CH043AA-C ( FCC ID :RAR20000003) module as well one B2XH068AA-A module.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Module installation in a BA100 clam shell The assembly is made up of two bolted clamshells. The modules are installed in the bottom clamshell. Figure 5 outlines how boards are installed. Refer to document RAR20007001_BelAir WRM Label Information.pdf for FCC label location details for the module. Two B2XH068AA-A ( FCC ID :RAR20007001) modules or one B2CH043AA-C ( FCC ID : RAR20000003) module LPM digital board Bottom clamshell Fig.
WRM Product Manual – 2.6 GHz WCS Band Radio Module BA100 Unit FCC Labeling One or more labels are applied to the product during manufacture, including a label which identifies the FCC identification numbers. Refer to figures 7 through 10 for label location on BA100 product. Do not attempt to remove any labels from the module.
WRM Product Manual – 2.6 GHz WCS Band Radio Module BA 100S Unit FCC Labeling Fig. 9 Fig. 10 Location of FCC labels for BA100S located on top and bottom clamshells outlining the radio modules contained in the unit.
WRM Product Manual – 2.6 GHz WCS Band Radio Module B2XH068AA-A module installation into BA200 product The module can be installed in a BA200 product. The BA200 can accommodate up two four radios. Four B2XH068AA-A ( FCC ID :RAR20007001) modules or one B2CH043AA-C ( FCC ID :RAR20000003) module as well three B2XH068AA-A modules are the possible variants.
WRM Product Manual – 2.6 GHz WCS Band Radio Module A typical block diagram of the BA200 is shown in figure 13. The BA 200 is a multiple radio product incorporates up to four B2XH068AA-A modules. The unit incorporates power line conditioning, battery back up and charging, Ethernet interfaces, and switch and control circuitry. B2XH068AA-A Backhaul radio cards (RAR20007001 ) Fig.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Module Installation into a BA200 unit The core of the BA200 unit is made up of two clam shells as shown in figure 14. The three B2XH068AA-A modules are installed below the SCM digital board. B2XH068AA-A B2CH043AA-C module Digital Board Power Supply Fig.
WRM Product Manual – 2.6 GHz WCS Band Radio Module BA200 Unit FCC Labeling One or more labels are applied to the during manufacture, including a label which identifies the FCC identification numbers. Refer to figure 15 for label location on BA200 product. Do not attempt to remove any labels from the module.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Antenna Usage and Module Transmit Power B2XH068AA-A module shall only be used in conjunction with the following antenna types: • MTI Wireless Edge MT-36012/SV 10 dBi patch antenna • MTI Wireless Edge MT-36013/SV 10 dBi patch antenna • MTI Wireless Edge MT-364002/A 16 dBi panel antenna In order to comply with the FCC rules in the USA, the module is limited to the maximum transmit power limits as follows for each of the antenna types.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Installation Products which contain B2XH068AA-A shall only be installed by professional installers trained by BelAir Networks or its authorized agents. In addition to normal installation procedures and good installation practice, professional installers are responsible to ensure that: 1. Only an approved antenna (see above) is connected to the module, and, 2.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Regulatory Statements The following regulatory notes apply to the product which contains module B2XH068AA-A (FCC ID: RAR20007001). The following sections or equivalent information shall appear in the user-manual of the final product. Regulatory Information and Disclaimers Installation and use of this device must be in strict accordance with the instructions included in the user documentation provided with the product.
WRM Product Manual – 2.6 GHz WCS Band Radio Module RF Exposure Statement This Wireless radio device has been evaluated under FCC Bulletin OET 65C and found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, 2.1093, and part 27.52 addressing RF exposure from radio frequency devices. This device complies with FCC RF radiation exposure limits for an uncontrolled environment. The radiated output power of this Wireless device is below the FCC radio frequency exposure limits.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Appendix A – Information on approved module antennas Specification for antenna MT-362012/SV for mounting in a BA200 unit: Photo of MTI patch antenna type MT-362012/SV mounted in one plastic external sector of the BA200 unit.
WRM Product Manual – 2.
WRM Product Manual – 2.6 GHz WCS Band Radio Module Specification for antenna MT-362013/SV for mounting outside a BA100 unit: Photo of MTI patch antenna type MT-362013/SV BelAir Networks Inc. 603 March Road Kanata, Ontario Canada K2K 2M5 Sales sales@belairnetworks.com Support support@belairnetworks.com General Information Info@belairnetworks.