CDMA Fixed Wireless Phone LSP-450 User Guide Please read this manual carefully before operating your set. Retain it for future reference. P/NO : MMBB9223301 MAR/2009/ISSUE 1.
Introduction 1. Introduction ① ② ③ ④ ⑪ ⑦ Menu C OK + - ⑨ ⑩ ⑥ ① Menu : Activates Main Menu state. ② Clear : Deletes the last digit, or moves previous Menu. ③ OK : Used to store an entry or to accept a command. ④ Up Key (+) : Moves up in the Menu or Volume Up. ⑤ Down Key (–) : Moves down in the Menu or Volume Down. ⑥ END/PWR : Deactivates states, or Power ON/OFF. ⑦ Redial/Flash : Activates Redial/Flash state, or views CallHistory. ⑧ ( ) : Activates hands free function.
Introduction 1.2 LCD Display Introduction The LCD shows icons on the top of the LCD screen. Different indicators appear based on the phone's operating mode. Icon Operating Condition RSSI Indicator : Indicates the signal strength in the service area. No Service : The phone is not receiving any system signal. In Use : Displayed when a call is in progress or the phone is in off-hook state. Text Message : Displayed when a text message is received. Voice Message : Displayed when voice message is received.
Introduction STEP III. Connect Components ▶The following components are supplied Fixed Wireless Phone. 1. LSP-450 Main Phone with Handset (Including inner backup battery) -1EA2. Dipole Antenna- -1EA3. AC/DC Power Adapte -1EA4. User Guide -1EA▶Please make sure that these components are present before youbegin to install the phone. If any of the components are missing or damaged,contact your service provider immediately. (Please refer to “Installation Steps” in 1.4) STEP II.
Introduction STEP IV. Check the LCD Display Introduction ▶After you follow the installation instruction step I to step III,please check the LCD for normal operation. ▶If you do not see the status of service, please repeat the 4thinstruction of step III. ▶Then confirm the status of phone to get the proper signalstrength from the service operator system. 1.4 Installation Steps Please follow the procedure below to install the phone properly. 1 Connect basehandset to the handset connector.
Basic Operation 2. Basic Operation 2.1 Making a Call Dial/Flash END/PWR 2.2 Redialing Last Number 1. Pick up the handset or press button. 2. Listen for dial tone. 3. Press Redial/Flash button. 4. The call is connected and you may start conversation. 5. To disconnect the call, replace the handset or press button. 2.3 3-way Call Conferencing Method 1 1. Enter the phone number of the 2nd party phone while you are intelephonic conversation with 1st party. 2. Press Redial/Flash button. And press buttonagain.
Basic Operation 2.6 Receiving a Call Basic Operation When the bell rings in idle state, you can receive a call as follows: button. 1. Pick up the handset or press the 2. Start a conversation. To disconnect the call, replace the handsetor press the button. 2.7 Memo Allow you to store number during the call. To store number : 1. Press Menu + 2( Memo ). 2. Enter up to 32 numbers using the keypad. 3. Press OK key to save. To retrieve an In Call Memo : 1. Press Redial/Flash button to see saved number. 2.
Menu Tree 3.1 PHONE BOOK Up to 300 entries can be listed here. 1. Enter the area code and phone number (Max. 32 digits) in on-hook state. 2. Press OK key and enter name. 3. Enter the desired memory location. 4. The phone will display a message asking you whether to keepyour number as secret or not. Select NO or Yes using Up/Down button and press OK key. 3.1.1 Find 1. Press Menu + 1( PHONEBOOK ) + 1( Find ) in 1. Press Menu + 1( PHONEBOOK ) + 3( Erase All ) in on-hookstate. 3.
Menu Tree 3.2.3 SMS 8282 Menu Tree 1. Press OK + 3( SMS 8282 ) in on-hook state. END/PWR Dial/Flash 2. You may select from nine items (1. What’s New? / 2. News / 3. Cricket / 4. Astrology / 5. Win Prizes / 6. Stocks / 7. Fun / 8. LifeStyle / 9. More ). 3.2.4 Outbox All your successfully sent messages are saved here. 1. Press OK + 4( Outbox ) in on-hook state. 3.2.
Menu Tree 3.3.1 All Call 1. Press Menu All Dialled + 3( CALL HISTORY ) + 1( All Call ) or 4. After you press OK key, press OK key to see more information and press OK key to save the number in the phonebook. 3.3.2 Missed 1. Press Menu + 3( CALL HISTORY ) + 2( Missed ) in on-hookstate. 3.3.3 Received 1. Press Menu + 3( CALL HISTORY ) + 3( Received ) in on-hookstate. ) in on-hookstate. 3.3.5 In Call Memo 1. Press Menu + 3( CALL HISTORY ) + 5( In Call Memo ) in on-hookstate. 3.3.