Digital Key Telephone Quic k Guide LDP- 9030D Please read this manual carefully before operating your set. Retain it for future reference.
Important Safety Information To prevent the unexpected danger or damage please read this information before installing and repairing the phone. There are “Warning”, it means as follows; Warning: To reduce the possibility of electric shock, do not expose your phone to high humidity areas, such as a bathroom, swimming area, etc. Warning 1. Only trained and qualified service personnel shall install, replace or service the phone. 2. Do not spill liquid like water on the phone.
LDP-9030D Digital Telephone Description Quick Guide Fixed Feature button definition Button Description 3 Soft Used in conjunction with fixed and flexible features, and the function changes in relation to call progress, as indicated on the LCD display. Page Used to change more additional functions on the LCD display . Trans/PGM This button is used to initiate a call transfer (TRS) or to enter programming mode (PGM).
LDP Keyset User Operation Receiving calls _ Answering a Call While Idle : 1. Lift the handset and press the flashing Flex button (as needed), the call will be connected. Responding to a Call While Busy 1. Press [Hold/Save] and/or 2. Press the flashing CO line button. Answering Calls to Other Stations To answer a call ringing at another station: 1. Lift the handset, 2. Dial 7 (Directed Call Pick-Up code), 3. Dial the Intercom Number of the ringing station; the call will be connected.
User Program Codes • ▶ Press the [Trans/PGM] button • ▶ Enter the desired feature code below table CODE FUNC TION CODE FUNC TION 11 Answer mode (H/T/P) 56 Create Conference Room 12 Station Name Program 57 Delete Conference Room 13 Set Wake Up 61 Speaker/Headset PGM 14 Reset Wake Up 62 Headset Ring Program 15 Language Program 71 Register Station ICLID 16 LCD Date Mode Change 72 View Station ICLID 17 LCD Time Mode Change 73 Outcall Notification Enable 18 Set Back Light 74 Ou
Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15.21 Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment.
1. Introduc tion The LDP- 9000BTU c an be c onnec ted to a c ompatible Bluetooth headset that supports Bluetooth tec hnology. (version 1.1 or higher) This allows you freedom to make and rec eive c alls while on the move or in the offic e. Read this user's guide c arefully before using the LDP9000BTU. 2. Bluetooth wireless technology Bluetooth headset is spec ially designed for spec ial phones (suc h as GS M, C DMA mobile phone)may be not c ompatible with the LDP- 9000BTU.
3- 1. Unpac king Unpac k the box and c hec k the items below : LDP- 9000BTU Installation guide 3- 2. Installation. when installing or removing the option module the Line power must be stopped. If not, in the worst c ase, will damage the option module or Keyset. ※ C aution The Optional Unit connec tion should make earlier and break later than the line cord. a. After disc onnec ting the line, open the dummy c over.(①②) (on the bottom of the keyset) b.
4. Before you use the LDP- 9000BTU 1. Make sure that the bluetooth headset is c harged. 2. Enable the Bluetooth Usage. ( PGM + 6 + 1 ) F or more information, see the user's guide of the LDP- 9030D. 3. You must first pair LDP- 9000BTU with the headset you want to use. The Bluetooth c onnec tion between the headset and LDP- 9000BTU c an be established by setting up a paired link.
5. Using Bluetooth menu [ PGM+ 6 + 3 ] 5- 1. When Blutooth Usage is enable. 1. PAIRING 2. UNPAIRING EXIT NEXT OK 3. PAIRED INFORMATION EXIT NEXT OK 5- 2. When Blutooth Usage is disable.
6. PAIRING 6.1 When already paired ALREADY PAIRED EXIT BACK 6.2 S earching for Device SEARCHING FOR DEVICE PLEASE WAIT... EXIT ※ Note. It may take about 15 sec onds to finish searc hing for devic es. 1. Before you c an pair your headset you need to put it into pairing mode. (Note: Pairing must be done every time the Headset establishes a link with LDP- 9000BTU. Refer to headset’ s user guide for more detail information.) 2.
6.3 S elect device [1/2] JABRA BT250 00-07-A4-04-8D-9B EXIT NEXT OK 1. Devic es responding to the inquiry appear on a list of Bluetooth devic e starting from the devic e found first after 15 sec onds. 2. S c roll to the devic e you want and press [ OK] or [ Hold/S ave] .
6.4 Enter devic e PIN CODE(PAS S WORD) ** ENTER PIN CODE ** CODE : EXIT DEL OK 1. The desired bluetooth devic e requests to enter the pinc ode of it. (The Bluetooth Passc ode is a 1 to 16 c harac terlong numeric c ode. ) 2. Enter the pinc ode and send to headset by pressing [ OK] or [ Hold/S ave] . 3. When the c onnec tion has been established, the devic e shows c onnec ted to followed by the devic e's name and address. ( Note that you c an have only one ac tive c onnec tion at a time. ) 4.
8. PAIRED INFORMATION JABRA BT 250 (HS-C) 00-07-A4-8D-9B EXIT BACK JABRA BT 250 (HS-C) Devic e S tatus D Disc onnec t Already paired but not linked- radio with headset C C onnec t Ready to make and answer a c all. 9. LED Indic ation The LDP- 9000BTU indic ates c urrent status using LED on the bottom of phone. OF F not paired or Bluetooth Usage disable status. S TEAD Y ON Already paired but not linked- radio with headset BLINK Ready to make and answer a c all. 10.
10.2 Make a call from the phone Using the phone’ s keypad, dial the phone number in BTU mode of the phone. ( S et PGM + 6 + 1 ) 10.3 Make a call from the headset 1. Press headset’ s func tion button. 2. You will hear dial tone. 3. Dial the phone number. 10.4 Ending a call from the headset 1. Press headset’ s func tion button. 2. Or press the [ S peaker] button of phone 10.