LIP-8040L User Guide
Revision History Issue 1 Date Aug. 08 Remark Initial Release Disposal of your old appliance 1. When the crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by government or the local authorities.
Important Safety Information To prevent unexpected danger or damage please read this information before installing or attempting to repair you phone. Warning and Caution information is provided to alert the consumer of known dangers: Warning: To reduce the possibility of electric shock, do not expose your phone to high humidity areas, such as a bathroom, swimming area, etc. Caution: Use only LG-Nortel approved batteries and desktop chargers to avoid the damage to the phone.
LIP-8040L User Guide Issue 1 TABLE OF CONTENTS 1. INTRODUCTION ............................................................................................1 1.1 1.2 1.3 1.4 1.5 2. General................................................................................1 Feature Information..................................................................1 Feature Groupings...................................................................1 iPECS LIP-8040L Phone Description ................................
LIP-8040L User Guide Issue 1 4.1.2 Leaving a Message Wait ................................................. 26 4.2 External Calls ...................................................................... 26 4.2.1 Placing external CO/VoIP calls.......................................... 26 4.2.2 Waiting for the next available CO/IP line .............................. 28 4.2.3 Account Codes: Tracking External calls for billing.................... 28 4.2.4 Disable dialing from your phone ........................
LIP-8040L User Guide Issue 1 8.10 Hot Desk ............................................................................ 51 9. PBX, CENTREX & ISDN FEATURES ...........................................................53 9.1 Access PBX or Centrex features ................................................ 53 9.2 Access the ISDN Network ........................................................ 53 9.2.1 Using the Keypad facility to access ISDN features................... 53 9.2.
LIP-8040L User Guide Issue 1 iv August, 2008
LIP-8040L User Guide 1. Introduction Issue 1 1. INTRODUCTION 1.1 General Your telephone is connected to an advancedtechnology, highly-versatile, fully-featured telecom system designed to make office communications easy and productive. Employing state-of-the-art Voice over Internet Protocol (VoIP) technology, voice and data converge on a single IP packet network. Because each iPECS Phone is an IP appliance, it can be moved easily throughout the office LAN and maintain normal operation. 1.
LIP-8040L User Guide Issue 1 Features have been divided into groups, Receiving Calls, Placing Calls, etc. Within each group, features are arranged according to the difficulty of operation and frequency of use. 1.4 iPECS LIP-8040L Phone Description The iPECS LIP-8040DL Phone (shown) incorporate the latest in VoIP technology and user interface to provide you with a cost effective, simple to use, productive communications tool.
LIP-8040L User Guide Issue 1 iPECS LIP-8040L Diagram 1.5 LIP-8040L Phone Installation The phone handset is attached as shown (A). The LIP8040L has 2 RJ-45 and 10/100 Base-T LAN connection ports (shown). One port is for connecting to the LAN (D), and the other can be connected to a desktop data device or PC (B), or another LAN interface terminal.
LIP-8040L User Guide Issue 1 1.5.1 Power All LIP-8000 series phones can be powered by the AC/DC Adapter-K- (48 VDC @0.3A; shown “C” in previous graphic) or over the LAN cable using the POE8 or other 802.3af compliant switch. If using the AC/DC Adapter, after connecting the Phone to the LAN, the Adapter’s DC voltage plug is inserted into the power-input jack in the underside of the Phone.
LIP-8040L User Guide • • • • Issue 1 Mark and drill two (2) 7mm holes for plastic wall anchors. Insert the two (2) anchors into the holes and insert and tighten the each screw leaving about 2.5 mm (1/8inch) of the screw exposed. Slide the LIP-8000 phone over the screws and assure the phone is secure. NOTE—It may be necessary to remove the phone and tighten or loosen the screws for a secure mounting.
LIP-8040L User Guide 2. LCD, Speakerphone & Related Features Issue 1 2. LCD, SPEAKERPHONE & RELATED FEATURES 2.1 Using the LCD The iPECS LIP-8040L has a large 9-line, 24 character across Liquid Crystal Display (LCD) which is divided into 3 sections. The upper section consists of 3 lines. nd rd The first line displays various icons. The 2 and 3 line are used to convey information to you. They provide the date, time and station number display while idle.
LIP-8040L User Guide Issue 1 To activate the Display Menu: • • • Press MENU button, Press the Navigation up/down buttons and press the OK Soft button to select, OR Dial the associated digit (Menu selections shown): Select (0-4) 1. PHONE SETTING 2. CONFERENCE ROOM PGM 3. ICM SMS 4. Network Config 0. Attendant BACK OK NOTE—The ‘0. Attendant’ selection display on the System Attendant phone. will only 2.2.
LIP-8040L User Guide Issue 1 Select (1-8) • • • • • • • 6. STA RING DOWNLOAD 7. BACKLIGHT • 8. FONT PROGRAM BACK OK Station Name Program—Input up to 12 digits using the keypad (press DND button to backspace/delete a character), then press the OK Soft button. To input characters: o Press the second Soft button to select ABC> or abc> mode, o To input the first character of a button, press the button 1 time (ex.
LIP-8040L User Guide Issue 1 2.2.2 Conference Room The User can create and delete Conference rooms. To configure a Conference Room: • • Press MENU button and 2 (Conference Room), The following menu displays: SELECT (1-2) 1. CREATE CONF ROOM 2. DELETE CONF ROOM • • • • • BACK OK Press the Navigation up/down keys to highlight and then press the OK Soft button to select, OR Dial the number associated to the selection, Enter the room number and dial the password, Press the OK Soft button. 2.2.
LIP-8040L User Guide • • • • Issue 1 Dial 1 to send a message, Dial 1 if resending, or 2 to send a new message (edit), Enter the Station number and message (if sending message), Press the OK Soft button. To retrieve a SMS message: • • Press MENU button and 3 (ICM SMS), The following menu displays: SELECT (1-2) 1. SEND MESSAGE 2. IN BOX(03) • • • • BACK OK Press the Navigation up/down keys to highlight and then press the OK Soft button to select, OR Dial 2 to retrieve a message.
LIP-8040L User Guide Issue 1 To set default Config. settings: • In Network Config. Menu, use VOL S T buttons to locate the Default Config. Screen (shown), SET DEFAULT CONFIG(DOT:*) • Press the * key. To exit Config. settings: • • • Press the SPEAKER button, Press the * key to exit, OR Press the # key to Reset/Reboot the phone with new setting. 2.2.5 Attendant menu The Attendant menu is only available on the System Attendant phone.
LIP-8040L User Guide • • • • 2.3 Issue 1 Set ICM Only Mode—Dial the Station Range for ICM only calls (ex., 103-108=103108), and press the OK Soft button. Restore COS—Dial the Station Range for COS restoring (ex., 103-108=103108), and press the OK Soft button. Monitor Conference Room—Enter the Conference Room number to view the number of attendees in the Conference Room. Delete Conference Room—Enter the Conference Room number and press the OK Soft button to delete.
LIP-8040L User Guide Issue 1 To Mute the microphone: • Select the MUTE button. To turn off Mute (turn the microphone ON): • Press the MUTE button. To activate Group Listen while on an active handset call: • 2.4 Press the SPEAKER button. Using a Bluetooth Wireless Headset The iPECS LIP-8040L may be equipped with a Bluetooth Unit (BTU) allowing you to use a wireless headset that supports Bluetooth version 2.0.
LIP-8040L User Guide Issue 1 To unpair the BTU headset: • • • • • Set the Bluetooth headset to pairing mode, Press the TRANS/PGM button, Dial *8, Dial 2 (disable), Press the OK soft button. To check BTU paired information: • • • • Press the TRANS/PGM button, Dial *8, Dial 3, Press the OK soft button. To use the BTU headset: • • • Press the SPEAKER button, OR Press the Call Start button on the BTU headset, Place call as you normally would.
LIP-8040L User Guide Issue 1 LIP-8012DSS LIP-8012LDSS LIP-8048DSS To use a Serial DSS: • • • • • • • Verify the Station has Serial DSS Usage authority (Admin PGM111-Flex21), Verify the DSS power is OFF (LIP-8048DSS only), Power-OFF the phone, Connect the serial DSS to the phone, Power-ON the phone and the DSS (LIP-8048DSS only), Program the DSS button using Web Admin Programming or PGM115, Edit LSS label from Admin PGM129 (default label is provided from MFIM).
LIP-8040L User Guide 3. Receiving Calls Issue 1 3. RECEIVING CALLS 3.1 Answering a Call While Idle There are 3 basic types of incoming calls; internal/external ringing calls, Intercom Voice Announce calls, and Hold recalls. Your phone may be assigned Ringing Line Preference; in this case, calls that ring are answered by lifting the handset. Otherwise, you must press the flashing Flex button. External calls to an iPECS Phone will appear under the CO/IP line or a LOOP button.
LIP-8040L User Guide 3.2 Issue 1 Responding to a Call While Busy While you are busy on another call, you may receive a Muted Ring, Camp-On tones, or Voice-Over announcements. Muted Ring is provided over the speaker of your Phone indicating a Call Waiting. You also may receive Camp On tones, a burst of tones on top of the existing call, as an indication of another call waiting. While busy, certain stations can activate Voice-Over to your phone.
LIP-8040L User Guide Issue 1 Ring mode—the Answering Machine Emulation (AME) Flex button will flash to notify you of a call. You may press the Flex button to hear the caller as the voice message is stored. Speaker mode—when the call is sent to the voice mailbox, the caller’s voice is automatically broadcast over the speaker of your iPECS Phone.
LIP-8040L User Guide Issue 1 To download a Ring Tone from System memory: • • • • • • Press TRANS/PGM , Dial 1 for Ring Tones, Dial 5 for Ring Tone download, Dial the phone’s memory location to receive the tone (5-8), Dial 0-9 for the desired tone number; a confirmation tone is heard, Press HOLD/SAVE to download. To select a Ring Tone from phone memory: • • • • • 3.
LIP-8040L User Guide Issue 1 To answer a call ringing at another station: • • • Lift the handset, Dial 7 (Directed Call Pick-Up code), Dial the Intercom Number of the ringing station; the call will be connected. To answer a call ringing at a station in your group: • • 3.7 Lift the handset, Dial 566 (Group Call Pick-Up code), the call is connected. Using Do-Not-Disturb (DND) to Block Incoming Calls Activate Do-Not-Disturb when you wish to not be interrupted; the phone will block incoming calls.
LIP-8040L User Guide Issue 1 1: Unconditional—all calls to the station, except recalls, are forwarded. 2: Busy—Immediately forwards all calls, except recalls, when the station is busy. 3: No Answer—forwards all calls to the station, except recalls, when the station does not answer within the No Answer timer. 4: Busy/No Answer—forwards calls if the station is busy or does not answer within the No Answer timer. When you forward calls from a different station, you may need to enter your Authorization Code.
LIP-8040L User Guide Issue 1 3.8.2 Forwarding calls to an external number Forward calls to an external destination; calls can be forwarded from an internal station or a remote location. You may define the conditions or ‘type of forward’ as listed below: 1: Unconditional—all calls to the station, except recalls, are forwarded. 2: Busy—Immediately forwards all calls to the station, except recalls, when station is busy.
LIP-8040L User Guide Issue 1 To activate Call Forward, Off Premise (forward to an external number) from a remote location: • • • • • • • Lift the handset, Dial the telephone number of a DISA assigned CO line, While receiving dial-tone, dial 554 (Call Forward feature code), Dial your Authorization Code (your Station number + Password), Dial the type of Forward code (6-9), Dial Speed Dial bin number, Replace the handset, return to idle. 3.8.
LIP-8040L User Guide Issue 1 To activate Custom or Pre-Defined Message Forward: • • • • • Press TRANS/PGM , Dial User Program feature code 51, Dial the two-digit text Message code (00-20), Dial any auxiliary input for messages 01-04 and 06-08, Press HOLD/SAVE , forward confirmed. To cancel activated Message: • • Press the Fwd Soft button, Dial #.
LIP-8040L User Guide Issue 1 4. PLACING A CALL 4. Placing Calls 4.1 Internal Calls You can place calls to other stations in the system over the Intercom. The call will ring, or for an ICM Voice Announce call, a splash tone will be heard. Ring or Voice Announce is normally determined by settings at the called station but you may change this by dialing ‘#’ after placing the call. By changing the mode, a Voice Announce call will ring or a ringing ICM call will allow Voice Announce (toggle).
LIP-8040L User Guide Issue 1 busy station returns to an idle state, the system will call your Station; after you answer the callback, the system will call the previously busy station. If you are the Attendant or Secretary, you may activate Intrusion. You may also use Step Call; dial the next station by dialing the last digit of the Intercom number. To Camp-On (wait off-hook) for a busy station: • Press * and await an answer.
LIP-8040L User Guide Issue 1 Individual CO/IP line access— 88 + Line number (01-42 for iPECS-100, or 001200 for iPECS-300 & 600). CO/IP Group access— 801-820 for iPECS-100, or 801-872 for iPECS300 & 600 Any CO/IP Line access— 9 When dialing on a CO line which uses pulse style signals, you may activate Dial Pulse to Tone Switchover changing to DTMF style dialing (for banking services, etc.). When placing an IP call, you must dial an IP address using the ‘*’ key in place of the dot.
LIP-8040L User Guide Issue 1 4.2.2 Waiting for the next available CO/IP line If all the lines connected to your system are busy, you will receive an All Trunks Busy signal. You may request to be notified when a line is available for use. To activate a queue if the selected/dialed line is busy: • • Select the desired CO/IP line button; when the busy notification is returned, press the MSG button, Return to an idle state by going on-hook; when the line is available, the Station will be notified (ringing).
LIP-8040L User Guide Issue 1 To deactivate Temporary COS: • • • • Press TRANS/PGM , Dial 22 (User Program code), Dial your Authorization code, Press HOLD/SAVE . 4.2.5 Temporarily override dialing restrictions at a phone Override the dialing restrictions at any phone by activating Walking COS. The Walking COS dialing restriction levels are applied for a single call only. For multiple calls, you will need to reactivate Walking COS or use the Flash Soft button to regain CO/IP dial-tone.
LIP-8040L User Guide Issue 1 4.3.2 Using and Entering Saved Number Dial You may store the last number dialed on an external call to the Saved Number Dial buffer for convenient dialing at a later time. The Saved number is stored until a new number is saved. To place a call using Save Number Dial: • • • Lift the handset, and/or press the DIR Soft button, Press Speed Soft button, Dial #. To store a number in the Save Number Dial: • While on an outgoing external call, press the Save Soft button. 4.3.
LIP-8040L User Guide Issue 1 4.3.4 Using and Entering Station Speed Dial Numbers Each station in the iPECS-100 System is allocated memory for 20 Station Speed Dial numbers (bins 0019) each up to 48 digits. The iPECS-300 & 600 support 100 Station Speed Dial numbers (bins 000-099). These numbers are entered at the user’s station and may include several ‘special’ instructions. Special instructions and the corresponding button are: PAUSE will momentarily stop dialing.
LIP-8040L User Guide Issue 1 To place a call using Station Speed Dial: • • • Lift the handset, and/or press the DIR Soft button, Press the Speed Soft button, Dial the desired Station Speed Dial bin number (00-19 or 000-099).
LIP-8040L User Guide Issue 1 NOTE—To allow others to contact you via the Intercom directory, you must enter a name for your station (up to 12 characters). To place a call using Dial by Name: • • • • Press DIR Soft button, Dial the desired directory, 1: Private directory, 2: Public directory, 3: Intercom directory, the LCD will display the names in alphabetical order, Scroll using the Navigation up/down keys, or enter search characters (refer to the Character Entry Chart in Section 4.3.4).
LIP-8040L User Guide Issue 1 button, or lift the handset. Either of these actions will cancel the ACNR request as well as connect you to the remote party. To set up ACNR, while on an outgoing call: • • Use the Navigation button to display the next menu and select the ACNR Soft button, Hang-up handset. To cancel the ACNR request: • Press the Stop Soft button.
LIP-8040L User Guide 5. Call Handling Issue 1 5. TRANSFER, CONFERENCE & OTHER CALL HANDLING 5.1 Call Transfer: Sending a call to a different destination You can send an active call to another station or other resource of the system, Call Transfer. You can screen the transfer with the receiving party (Screened Call Transfer) or complete the transfer without screening (Unscreened Call Transfer). Transferred calls, internal or external, are place in Transfer Hold.
LIP-8040L User Guide Issue 1 different ring signal. If not answered in a timely manner, the Attendant will receive Attendant Hold Recall. To place a call on Hold: • 5.3 Press HOLD/SAVE . Broker Call: Switching between two calls You may switch between the active call and a call on Hold, placing the active call on Hold acting as a broker between two or more parties (Broker Call). iPECS Phone users may ‘broker’ for multiple calls up to the number of CO/IP line buttons.
LIP-8040L User Guide Issue 1 To place a Conference on Hold: • Press the HOLD/SAVE button. To retrieve the Conference from Hold: • Select the Conf Soft button. To establish an Unsupervised Conference: • • • Establish conference with two external parties, Select the Conf Soft button, Hang-up the handset. To retrieve an Unsupervised Conference: • • Lift the handset, Select the Conf Soft button. 5.4.
LIP-8040L User Guide 5.5 Issue 1 Call Park: Placing a call on Hold to Page A user may transfer an active CO/IP call to a special holding location (Park Orbit), which can be accessed easily from any station in the system. Typically, this feature is used with Paging to notify the desired user of a parked call. Parked calls are subject to Hold Recall after the Call Park timer.
LIP-8040L User Guide 6. Send & Retrieve Messages Issue 1 6. SEND & RETRIEVE MESSAGES 6.1 Responding to a Station Message Waiting Indication Another station can leave a Station Message Waiting indication (MWI) when you do not answer or your phone is in DND mode. The message icon will be displayed on the LCD screen. If programmed, a flashing MSG LED on the iPECS Phone also will indicate when there is a Message Waiting (PGM 111-Flex10).
LIP-8040L User Guide Issue 1 To delete all Station MWIs: • • 6.2 Press the Delete Soft button, Press 3 (Delete All MWIs). Getting Voice Mail Messages When callers are forwarded or recall to your Voice Mail Box, they can leave a voice message, as part of the integrated VMIM/VSF module, the iPECS Feature Server or an external Voice Mail system. The Voice Mail system allows access to and management of received voice messages. While in your Mail Box, you have control of your password and Mail Box greeting.
LIP-8040L User Guide Issue 1 To access your Voice Mail Box from a Remote Location: • • • • • • 6.3 Lift the handset, Dial the telephone number of a DISA CO line answered by the VMIM/VSF Auto Attendant, At answer, dial # to receive the ‘Mail Box & Password’ prompt, Dial the Mail Box and password to receive the ‘Number of Messages’ prompt, Dial desired option codes, At completion of session, hang-up.
LIP-8040L User Guide • • Issue 1 1. ICM MWI(002) 2. VSF MSG(002) 3. VMS MSG(001) 4. UMS MSG(003) 5. ICM SMS(003) BACK OK Dial 5; the first few SMS messages are shown in brief, Dial the Message number to view the entire SMS message. To delete received Short text messages: • • Press the DELETE Soft button, Dial 1 to Delete the message, 2 to Cancel, or 3 to Delete all received Short text messages.
LIP-8040L User Guide 7. Remote System Access Issue 1 7. REMOTE SYSTEM ACCESS 7.1 Direct Inward System Access (DISA) DISA (Direct Inward System Access) allows remote users to gain access to the system’s resources (remote users may be required to enter an Authorization Code). The system will recognize remote user dialed inputs (call other stations, place calls over CO/IP lines, review voice mails, etc). To access system resources remotely: • • • 7.
LIP-8040L User Guide Issue 1 To Transfer a call from the mobile extension using the iPECS: • • • Dial “*” while on an iPECS call, Dial the desired extension, the call is transferred and the mobile phone returns to idle. Reconnect to the transfer by pressing the # key. NOTE— This feature is only effective with an ISDN CO line.
LIP-8040L User Guide 8. Misc. Features Issue 1 8. MISC. FEATURES 8.1 Call Log Users can view a log of incoming, outgoing and missed calls on the display (up to 99 records). A LOG Soft button provides simple access to incoming (called), outgoing (dialed) and missed (lost) calls. NOTE—if a call is missed, the LOG Soft button will be displayed as LOG(M); the missed call icon also will appear on the LCD.
LIP-8040L User Guide Issue 1 To save an external call to the Station Speed dial: • • • Use Navigation up/down buttons to highlight the desired external call item, Press the Select Soft button, Press the Save Soft button. The CO code in a log item is used to seize the co line when placing an external call using the call log. Up to 5 CO codes can be saved. The first CO code is sent from the system in the saved call log.
LIP-8040L User Guide Issue 1 To edit the CO code (positions 2-5 only): • • Use Navigation up/down buttons to highlight the desired item, Press the Edit Soft button to modify selection. To select the CO code: • • 8.2 Use Navigation up/down buttons to highlight the desired item, Press the Select Soft button. Contrast LCD contrast can be adjusted to enhance viewing ability. To change the LCD Contrast: • 8.3 While in an idle state, press the VOL S VOL T buttons to adjust the brightness.
LIP-8040L User Guide Issue 1 To turn on Background Music: • 8.4 Press HOLD/SAVE to cycle through the BGM selections. Using Internal, External and Meet-Me Paging The User can broadcast announcements to other stations and/or external speakers. Stations are assigned to one or more of the Internal Page Zones. The system has two External Page Zones that can be connected to external speakers.
LIP-8040L User Guide 8.5 Issue 1 Push-To-Talk (PTT) Page iPECS Phones can be assigned as a member of one or more of the system’s nine Push-To-Talk (PTT) page groups. Users separately log-in or log-out of any one or all PTT groups to which the phone is assigned. Once logged in, place or receive one-way page announcements to/from other users who are logged in to the same PTT group.
LIP-8040L User Guide 8.7 Issue 1 Alarm/Door Bell The system can monitor external Alarm or Door Bell contacts: Alarm Monitor—should the external contact activate, a unique Alarm Ring signal and LCD display may be received. To restart the monitor circuit, the external contacts must be deactivated and the Alarm Ring signal terminated. Door Bell—a unique Door Bell Ring (single tone burst) may be received each time the external contact is activated.
LIP-8040L User Guide Issue 1 ICM Signaling Mode (Handsfree/Tone/Privacy) Station IP Address Station Mac Address Number of messages x (x: number of all message waiting) Wake-Up Time (hh:mm) Do Not Disturb Forwarded to station xxx Forwarded to speed bin xxx Queued CO/IP line xxx Locked (Temporary COS) COS x To hear Date & Time memo: • • Dial the Voice Memo code (661 for iPECS-100, or *661 for iPECS-300 & 600), Date and Time memo is heard, “Date is May 2nd.Time is xx:xx pm”.
LIP-8040L User Guide Issue 1 Once logged-on, the Hot Desk station will take on the attributes assigned to your station number and you can make calls as normal. When logged-out, calls to your station number are forwarded to the chosen destination. To Log on to a Hot Desk station: • • Lift the handset, Dial your Authorization Code (Station Number and Password).
LIP-8040L User Guide 9. PBX, Centrex, & ISDN Features Issue 1 9. PBX, CENTREX & ISDN FEATURES 9.1 Access PBX or Centrex features The iPECS has been designed to operate with a host PBX system or Centrex services from your service provider. The iPECS connects to a host with analog CO lines. When accessing a CO line, the phone will act as an extension of the host, allowing access to the host system features using the host dial codes.
LIP-8040L User Guide Issue 1 To activate Keypad Facility operation: • • Press the programmed to keypad mode, Dial as desired. KEYPAD FACILITY button to switch To deactivate Keypad Facility operation: • • • Press KEYPAD FACILITY , OR Press a Feature or Flex button. 9.2.2 Using ISDN Supplementary Services ISDN service providers may incorporate features similar to those of Centrex.
LIP-8040L User Guide Issue 1 To restrict Caller ID: • • Lift the handset, Press programmed CLIR/COLR button to place call.
LIP-8040L User Guide 10. Features & Flex Buttons Issue 1 10. FEATURES & FLEX BUTTONS 10.1 Entering Station Program Data A special code set is available for iPECS Phone users to assign certain attributes such as Authorization Codes (Passwords). After entering the User Program mode, dial the codes to select the attribute and setting. Once selected, the setting is saved. A list of the User Program codes, the feature/function and any input required are given in Appendix B.
LIP-8040L User Guide Issue 1 APPENDIX A FLEXIBLE NUMBERING PLAN FEATURE iPECS -300 100399 501535 543 544 545546 548 549 550 iPECS600 10001599 501-535 External All Call Page All Call Page (Internal/External) SMDR Account Code Enter iPECS -100 100169 501510 543 544 545546 548 549 550 Flash Command to CO Line 551 551 551 Last Number Redial 552 552 552 DND (Toggle On/Off) 553 553 553 Call Forward Speed Dial Programming 554 555 554 555 554 555 Message Wait/Callback Enable 556 556 556 M
LIP-8040L User Guide FEATURE Alarm Reset Group Call Pickup Universal Night Answer Account Code with bin Walking COS Code ACD Supervisor On/Off Duty ACD Supervisor Login ACD Supervisor Logout ACD Help Code ACD Calls In Queue Display ACD Supervisor Status Display ACD Supervisor Monitor ACD Reroute Queued Call w/answer ACD Reroute Queued Call w/o answer Enter Conference Room Camp-On Answer Call Parking Locations Group Pilot Number Station User VMIM/VSF Features Call Coverage button Direct Call Pickup CO/IP Gro
LIP-8040L User Guide FEATURE Issue 1 Attendant Call VM Message Wait Enabled VM Message Wait Disable Door Open (1st Door ) Door Open (2nd Door ) Door Open (3rd Door ) iPECS -100 0 *8 *9 #*1 #*2 #*3 iPECS -300 0 *8 *9 #*1 #*2 #*3 iPECS600 0 *8 *9 #*1 #*2 #*3 Door Open (4th Door ) #*4 #*4 #*4 MCID Request AME Feature Unsupervised Conference Timer Extension code PTT Group Login/Logout *0 564 ## *0 564 ## *0 564 ## #0 #0 #0 59 REMARK iPECS300 & 600 iPECS300 & 600 August, 2008
LIP-8040L User Guide Issue 1 APPENDIX B USER PROGRAM CODES CODE 10 11 x 12 x FUNCTION Enblock Mode Dialing Differential Ring, Intercom Differential Ring, CO/IP line 13 x Intercom Answer Mode 14 x Call Coverage Attribute Setting 15 x Station Ring Download 19 21 Ear&Mic Headset Usage Knock Down Station COS 22 Restore Station COS 23 Walking COS 30 31 32 52 xx VM Mobile Notify Station Message Wait Retrieve CLI/IP Message Wait Retrieve Authorization Code (Password) Entry Assign DID CALL WAIT Bu
LIP-8040L User Guide Issue 1 CODE 55 61 x FUNCTION Monitor Conf.
LIP-8040L User Guide CODE *7 *8 *9 Issue 1 FUNCTION Force Fwd to Dest.
LIP-8040L User Guide Issue 1 63 August, 2008
www.lg-nortel.com ©2008 LG-Nortel Co. Ltd. All Rights Reserved.