User's Manual

ManualsBrandsEricsson Communications ManualsElectronicsGSM/GPRS 850 Transmitter

Table Of Contents

Ericsson Internal

INSTRUCTIONS 1 ( 14 )

/ XSNBRKI 4/1532-LZA 701 0001 Uen

EAB/ FJG/RSP ( Louise Cederlund) 2008-05-14 G

Prepared (also subject responsible if other) No.

Approved Checked Date Rev Reference

Verifying RBS Installations at Site

Disclaimer

No part of this document may be reproduced in any form without the written

permission of the copyright owner.

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

Contents Page

1 Introduction ....................................................................... 2

1.1 Revision Information .............................................................. 4

2 Prerequisites ..................................................................... 4

2.1 Documentation .................................................................... 4

2.2 Tools and Equipment ............................................................. 4

3 Visually Inspecting Equipment ................................................ 5

4 Switching On the RBS .......................................................... 6

5 Reading Fault Status ........................................................... 7

6 Testing External Alarms ........................................................ 7

7 Testing Battery Backup ........................................................ 10

8 Performing Concluding Routines ............................................. 11

8.1 Saving the IDB .................................................................... 11

8.2 Completing the Test Record ..................................................... 11

8.3 Filling in a Trouble Report ........................................................ 13

8.4 Filling in a Blue Tag Repair Delivery Note ...................................... 13

8.5 Filling in the Checklist ............................................................ 14

A4 XSEIF R5

Summary of content (14 pages)

PAGE 1
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 1 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Date Rev 2008-05-14 G Reference Verifying RBS Installations at Site Copyright © Copyright Ericsson AB 2006–2008. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner.
PAGE 2
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 2 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 1 Date Rev 2008-05-14 G Reference Introduction This document describes the tests that must be performed to verify the installation of the RBS cabinet. The RBS cabinet has already been tested at the factory.
PAGE 3
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 3 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Date Rev 2008-05-14 G Reference Work Process for Site Installation Verification This section describes the order in which to perform the tests. When the exit criteria are fulfilled, the tester should enter the results in the test record, see (Page 11) and return to the work process for the next step.
PAGE 4
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 4 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 1.1 Date Rev 2008-05-14 G Reference Revision Information Other than editorial changes, this document has been revised as follows: • Information on loading software added to section Preconditions and section Switching On the RBS 2 Prerequisites 2.
PAGE 5
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 5 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 3 Date Rev 2008-05-14 G Reference Visually Inspecting Equipment 1. Ensure that all cable connections at the front of the cabinet are correctly connected. 2. Check that all screws are tightened. 3. Check that no cables are damaged.
PAGE 6
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 6 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 4 Date Rev 2008-05-14 G Reference Switching On the RBS This section describes how to switch on the RBS. 1. Switch on the RBS main power. The switch for the RBS main power is located outside the cabinet 2. Switch on all applicable circuit breakers on the IDM. 3.
PAGE 7
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 7 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 5 Date Rev 2008-05-14 G Reference Reading Fault Status This section describes how to use the OMT to read the fault status, using the OMT. If any fault indicator on the RBS is on, then the fault status must be read. 6 1. Read the IDB, if it has not been read. See OMT User’s Manual. 2.
PAGE 8
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 8 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Date Rev 2008-05-14 G Reference P010475A Figure 3 External Alarms Testing 2. In the Available monitors box, select External Alarm Status and click → to add Alarm Inlets in the Monitors to start box. 3. Click Start Monitor. 4. Remove the external alarm covers. See document DF-OVP Installation Instructions. 5.
PAGE 9
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 9 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Note: Date Rev 2008-05-14 G Reference Always test the alarms in numerical order, starting with alarm1. Table 2 Closing/Breaking Alarms If: Then: a closing alarm is to be triggered short the alarm inlet on the customer side (the alarm cable is open when no of the OVP block.
PAGE 10
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 10 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Table 4 Date Rev 2008-05-14 G Reference Checking Released Alarms Yes Check the Following: The external alarm indicator on the DXU goes off The alarm disappears from the OMT 9. Repeat steps 6 to 8 for all defined external alarms. 10. Close the RBS Event Monitor window when finished. 11.
PAGE 11
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 11 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Table 5 Date Rev 2008-05-14 G Reference RBS Check with AC Power Off Check That: Yes The Battery Mode indicator on the BFU shows a constant yellow light The RBS is still running 2. Turn on the incoming AC power to the RBS.
PAGE 12
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 12 ( 14 ) No.
PAGE 13
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) Figure 5 13 ( 14 ) No. Date Rev 2008-05-14 G Reference Test Record 8.3 Filling in a Trouble Report This section describes when and how to fill in a trouble report. Write a trouble report when system components are not operating as expected, or when disturbances occur repeatedly.
PAGE 14
Ericsson Internal INSTRUCTIONS Prepared (also subject responsible if other) 14 ( 14 ) No. / XSNBRKI 4/1532-LZA 701 0001 Uen Approved Checked EAB/ FJG/RSP ( Louise Cederlund) 8.5 Date Rev 2008-05-14 G Reference Filling in the Checklist The following checklist is not compulsory but is strongly recommended. Local procedures and safety regulations must be evaluated and included in this checklist. Table 7 Site Installation Verification Checklist Check That: 1. All fault indicators are off 2.