Data Sheet

936.A3721a | Subject to alteration.
KATHREIN SE | Anton-Kathrein-Straße 1–3 | 83022 Rosenheim, Germany | Phone [phone] | www.kathrein.com | [e-mail]
Type No.
86010165
Protocols compliant to 3GPP/AISG 2.0/AISG 3.0
Logical interface ex factory 3GPP/AISG 2.0
Operates as Single RETs or Multi RET
Ex factory Single RETs
Input voltage range V 10 ... 30 (pin 6)
Power consumption W Typically < 1; < 10 (motor activated)
Connectors 2 x 8 pin connector according to IEC 60130-9; according to AISG-C 485
Daisy chain in: male; Daisy chain out: female
Hardware interfaces RS 485A/B (pin 5, pin 3);
power supply (pin 6); DC return (pin 7);
according to AISG / 3GPP
Adjustment time
(full range)
sec 40
(typically, depending on antenna type)
Adjustment cycles > 50,000
Temperature range °C −40 … +60
Protection class IP 24 (installed)
Lightning protection AISG interface (each pin)
2.5 kA (10/350 µs)
8 kA (8/20 µs) according to IEC 61000-4-5
Housing material Profile: Aluminum anodized; cover: Aluminum die cast coated
Weight g
lb
350
0.77
Packing size
(H x W x D)
mm
inches
245 x 93 x 102
9.6 x 3.6 x 4
Dimensions
(H x W x D)
mm
inches
142 x 71 x 51
5.6 x 2.8 x 2
Please note:
If the Primary which controls the FlexRET system does not support the default ex-factory interface set-
ting, then the FlexRET must be switched to the appropriate standard of the Primary before installation.
Please contact Kathrein for further information.
The FlexRET needs to be powered by a LPS (Limited Power Source, Class: P2) according to IEC/EN 62368-1.
If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna
after power on automatically. It is not necessary to configure the FlexRET manually.
Standards: EN 62368-1 (Safety)
EN 60950-22 (Safety – Equipment installed outdoor)
ETSI EN 301489-1 (EMI)
ETSI EN 301489-3 (EMI)
ETS 300019-1-4 (Environmental)
ETSI EN 300330 (Radio equipment)
EN 50364 (Health)
EU-RED: Hereby, KATHREIN SE declares that the radio equipment type 86010165 is in com-
pliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: http://www.kathrein.com
Certification: CE, FCC
Scope of supply: FlexRET
Optional: Site Sharing Adapter (86010154 or 86010155) to create independent logical
interfaces at one antenna or site. Makes it possible to operate with more than one
independent Node B. Operation in AISG 2.0 mode only.
Gender Adapter (86010162) to convert the AISG out (female) to an AISG in (male)
port in order to operate one FlexRet with exactly 2 BTS.
Detailed information is given in the data sheet of the Gender Adapter.
Port Extender (86010163) to convert the existing AISG input and output in order to
operate FlexRet with exactly 2 BTS while maintaining the daisy chain capability.
Detailed information is given in the data sheet of the Port Extender.
Please note:
In general, the addressing of the FlexRET is automatically performed. Only in case the FlexRET is
manually addressed, the serial number has to be extended by the corresponding colour coding extension
(e.g. CSG351234-R1). The respective information can be found on the site documentation which is
included in the scope of supply.
86010165 Page 1 of 4
FlexRET
A flexible, integrated solution for adjusting the electrical downtilt of Kathrein FlexRET antennas.
•Compliant to 3GPP/AISG 2.0/AISG 3.0 •Daisy Chain feasibility
•Single RETs or Multi RET displayed •Pre-configured
• Individual user-specific configuration possible:
– Antenna sharing-assignment of certain RET-submits to RET-ports
– Antenna tilt consolidations for RET control of several arrays by one RET-submit