TV WAll Mount Instruction Manual V2.0 Model: EI6171 Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact at support@ergo-innovate.
IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at ssupport@ergo-innovate.com. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury V1.
Verify Your Wall Construction CAUTION DO NOT install into drywall alone Wood Studs (with Drywall) Solid Concrete or Concrete Block If you are are not sure the wall construction, please contact our product support line at ssupport@ergo-innovat e.com. Tools Needed (Not lncluded) Stud Finder 5/32 in. (4mm) Wood Drill Awl Tape Measure Pencil Hammer 3/8 in. (10mm) Wood Drill Drill Phillips 3/8in.(10mm) Wrench Screwdriver 3/8in. (10mm) Socket Wrench 5/16 in.
[C] Spacers [If necessary] Note: The spacers are shown in accordance with the actual size. 2.5mm [C1] x8 10mm [C2] x4 22mm [C3] x4 [D] TV Bolts Note: The bolts are shown in accordance with the actual size.
CAUTION! A3 Wall Anchor x4 This anchor is for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs. Level 05 x1 Step 1 Secure the TV Brackets to TV Select TV Bolts Only one bolt size fits your TV. M4 M6 M8 Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV.
Option A (For Flat Back TV) 03 D D1/D2/D4 04 B B1/B2 C C1/C2 Alternate Setups Spacer (If needed) Option B (For Round Back TV) D D1/D3/D5/D6 03 B B1/B2 04 C C1/C2/C3 Alternate Spacer Setups Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.
Option D For cable interference or inset holes, use spacers [C1], [C2] and [C3] to create extra space between the TV and TV brackets C C1/C2/C3 D D1/D3 D5/D6 04 B B1/B2 Alternate Spacer Setups Step 2 Assemble Wall Plate(optional) Option A: 01 16 in. (406 mm) stud spacing and VESA Pattern of TV: 100X100-400X400mm E2 E1 Option B: 18-24 in. (457 mm-610 mm) stud spacing or VESA Pattern of TV: 02 200X100-600X400mm E2 02 DO NOT overtighten. Tighten only until snug. 06 E1 01 3/8 in.
Step 3 Attach Wall Plate to Wall For wood stud installation, follow STEP 3A For concrete installation, follow STEP 3B Step 3A Wood Stud Option WARNING: ● Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [01] or [01 and 02]. ● DO NOT USE ANCHOR FOR THIS STEP ● Ensure the wall plate is securely fastened to the wall before continuing to the next step.
2 23/64 in. (60 mm) 3-3 5/32 in. (ø4 mm) Drill 4 pilot holes using a 5/32 in. (4 mm) diameter drill bit. Make sure the depth is not less than 2.4 in.(60 mm). 3-4 A1 3/8 in.(10 mm) Socket Wrench (Not included) A2 Install the wall plate [01] or [01 and 02] using lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate.
3B-1 Position the wall wall plate [01] or [01 and 02] at your desired height, level the wall plate and mark the pilot hole locations. 2 9/16 in.(65mm) 3B-2 3/8 in.(ø10mm) Drill 4 pilot holes using a 3/8 in. (10mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in. (65mm). Never drill into the mortar between blocks. 3B-3 Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3] are seated flush with the concrete surface. A3 3B-4 3/8 in.
Step 4 Adjust the Tilt Angle of TV Note: The tilt angles of the hooks on the TV brackets must be the same. S Top 04 of 5/16 in. (8 mm) Wrench TV S S 03 Bo S Tighten S tto mo f T V Loosen Loosen the six preassembled tilt bolts [S] on both brackets, adjust the hooks on the brackets to the desired angle, then tighten tilt nuts using a wrench (not included) and the tilt tension bolts using a Phillips screwdriver (not included) to fix the tilting angle of TV.
Step 6 Secure TV to the Wall Plate [01] or [01 and 02] 04 03 Press Locking R Pull down and hold both cords [R], press the bottom of the TV into the wall plate [01] or [01 and 02] until the latches lock the TV in place. Step 7 Remove the TV HEAVY! You may need assistance with this step. R Unlocking Disconnect all cables, pull down and hold both cords [R] while gently pulling the bottom of the TV away from the wall.