TV Wall Mount Instruction Manual V1.0 Model: EI6153 Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact at support@ergo-innovate.
IMPORTANT SAFETY INFORMATION • Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at support@ergo-innovate.com. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
Tools Needed (Not lncluded) Stud Finder 5/32 in.(4 mm) Wood Drill Tape Measure Hammer 3/8in.(10mm) Socket Wrench 3/8 in.(10mm) Concrete Drill Pencil Phillips Screwdriver Drill Awl Supplied Parts and Hardware Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Product Support line at support@ergo-innovate.
05 TV Bolts [Only one bolt size fits your TV] Note: The bolts are shown in accordance with the actual size M4 M4 x 30mm [D] x4 06 M6 M6 x 15mm [E1] x4 M6 x 35mm [E2] x4 M8 M8 x 15mm [F1] x4 M8 x 35mm [F2] x4 G Supplied Part and Hardware for Step 2 Arm Assembly/Wall Plate 01 x1 Note: The lag screw is shown in accordance with the actual size A1 x3 Lag Screw ST6.3x60mm CAUTION! A2 x3 Wall Anchor φ10x50mm This anchor is for concrete or brick walls ONLY.
Step 1 Secure the Faceplate(or Faceplate with Extender Brackets) to TV 1-1 Choose the combination that applies to your VESA 8in.(200mm) 4in.(100mm) 16in.(400mm) 16in.(400mm) 12in.(300mm) 12in.(300mm) 12in.(300mm) For VESA hole pattern: 12x12 in.(300x300mm) 16x16 in.(400x400mm) 16in.(400mm) 3in.(75mm) 8in.(200mm) 4in.(100mm) For VESA hole pattern: 3x3 in.(75mmx75mm) 4x4 in.(100x100mm) 8x8 in.(200x200mm) 8in.(200mm) 3in.(75mm) H For VESA hole pattern: 12x8 in.(300x200mm) 16x8 in.
1-2 Select TV Bolts Only one bolt size fits your TV. M4 M6 M8 Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV. Too Short Too Long Correct Correct Please Note: When using the spacers it is important to note that they can be used in multi-layers (meaning stacked).
1-3 Attach the TV Bracket Option A (For Flat Back TV) 05 E1/F1/D 03 B (If needed) 04 C2 (If needed) Alternate Spacer Setups Option B (For Round Back TV) 05 D/E2/F2 03 B (If needed) 04 C1/C2 (If needed) Alternate Spacer Setups 06
Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY. D/E2/F2 05 B 03 (If needed) 05 E1/F1/D C1/C2 04 03 B Alternate Spacer Setups 04 C1/C2 (If needed) Alternate Spacer Setups Option D For cable interference or inset holes, use spacers 04 to create extra space between the TV and faceplate.
Step 2 Attach the Arm Assembly/Wall Plate [01] to Wall For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Step2A Wood Stud Option WARNING: ●Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the they are pulled firmly against the arm assembly/wall plate [01].
2A-3 Drill 3 pilot holes using a 5/32 in.(4mm) diameter drill bit. Make sure the depth is not less than 2 23/64 in. (60mm). 2 23/64 in.(60mm) ø5/32 in.(4 mm) 2A-4 A1 Install the arm assembly/wall plate [01]. using lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate. 01 UP 3/8in.
2B-1 Position arm assembly/wall plate [01] at your desired height, level the wall plate and mark the pilot hole locations. UP 2B-2 Drill 3 pilot holes using a 3/8 in.(10mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in.(65mm). Never drill into the mortar between blocks. 2 9/16 in.(65mm) ø3/8 in.(10mm) 2B-3 A2 Use the hammer to knock anchors [A2] into the wall. Be sure the anchors [A2] are seated flush with the concrete surface.
Step 3 Hang the TV onto the Arm Assembly/Wall Plate [01] ① Detach the preassembled bolts [S1] and washers [S2] and keep them for the next step. S2 ② Hang the TV to the S1 Arm Assembly. ③ Tighten the bolts [S1] and washers [S2] to secure TV to the arm assembly. S2 S1 HEAVY! You may need assistance with this step. Phillips Screwdriver (Not included) Tilt Adjustment 1. Slightly loosen the both bolts [S1]. 2. Adjust TV to your desired tilt angle. 3. Retighten the 2 bolts [S1] to hold TV in place.