Medium Full-Motion TV Wall Mount Instruction Manual V1.0 Model: EI6152 Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact at support@ergo-innovate.com.
IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at support@ergo-innovate.com. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
Tools Needed (Not lncluded) Stud Finder Awl 7/32 in. (5.5mm) Wood Drill Tape Measure 3/8 in. (10mm) Concrete Drill Pencil 3/8 in. (10mm) Socket Wrench Drill Hammer 1/2 in. (13mm) Socket Wrench Level Phillips Screwdriver Supplied Parts and Hardware Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts.
TV Bolts (Only one bolt size fits your TV) 05 Note: The bolts are shown in accordance with the actual size M4 M6 M4x30mm x4 F M6x15mm D1 x4 M6x30mm D2 x4 M8 M8x15mm E1 M8x45mm E2 x4 x4 Supplied Parts and Hardware for Step 2 Arm assembly/Wall plate 01 x1 Note: The lag screws are shown in accordance with the actual size A1 x4 Lag Screw M8x65 mm A2 x4 Washer M8 CAUTION! A3 x4 Wall Anchor This anchor is for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.
Step 1 Secure the TV Brackets to TV Select TV Bolts Only one bolt size fits your TV. M4 M6 M8 Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV. Too Short Too Long Correct Correct Note: If necessary, the spacers can be used in multi-layer. If the installation fails after trying various methods, please contact customer service at support@ergo-innovate.
Option B (For Round Back TV) D2/E2/F B (If needed) C1/C2 Alternate Spacer Setups Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.
Step 2 Attach the Arm Assembly/Wall Plate [01] to Wall For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Step 2A Wood Stud Option WARNING: Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the arm assembly/wall plate [01].
2A-2 HEAVY! You may need assistance with this step. Position the arm assembly/wall plate at your desired height and line up the holes with your stud center line. Level the arm assembly/wall plate and mark the holes. 01 2A-3 Drill 4 pilot holes using a 7/32 in. (5.5mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in. (65mm). 2 9/16 in. (65mm) ø7/32 in. (5.5mm) 2A-4 HEAVY! You may need assistance with this step.
Step 2B Solid Concrete or Concrete Block Option WARNING: Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the arm assembly/wall plate [01]. Ensure the arm assembly/wall plate is securely fastened to the wall before continuing to the next step. ● Mount the arm assembly/wall plate [01] directly onto the concrete surface ● Anything covering the wall must not exceed 5/8 in.
2B-3 HEAVY! You may need assistance with this step. A3 01 A1 Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3] are seated flush with the concrete surface. Install the arm assembly/wall plate using lag screws [A1] and washers [A2]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the arm assembly/wall plate. DO NOT over-tighten the lag screws [A1]. A2 1/2 in.
Step 4 Level Adjustment If needed, the TV can be levelled. 1. Slightly loosen the preassembled four nuts [L]. 2. Level your TV. 3. Retighten four nuts [L] to hold TV in place. L 3/8 in. (10mm) Socket Wrench (Not Included) Step 5 Tilt Adjustment 1. Slightly loosen four tilt nuts [T]. 2. Adjust TV to your desired tilt angle. 3. Retighten four tilt nuts [T] to fix the tilt angle.
Thank you again for choosing this ERGO-INNOVATE product! All of us at ERGO-INNOVATE do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us at support@ergo-innovate.com.