VACUUM SweepMOP Vacuum Sweep + Mop Model - VSM 6000 OWNER’S MANUAL Read the instructions carefully and keep for future reference
. Installation e.g. Charging Station not correctly connected Maintenance e.g. Failure to clean roller brush, HEPA filter, and other parts Mishandling e.g.
either 1. Open Smart Phone 2. Open Photo 3. Scan QR Code 4.
Safety Please follow the safety precautions listed below: This Vacuum Sweep Mop is not intended for use by children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Children should be supervised to ensure that they do not play with the appliance. Use only the power adaptor that is included with this appliance.
Parts and Accessories Main body Cleaning Brush Charging station HEPA Filter Roller brush Carpet brush HEPA Cleaning Brush Adapter 2
Product Description This appliance is intended for household use. The Vacuum Sweep Mop is a multiple function appliance, which can sweep, vacuum and mop many types of floor surfaces and carpets.
Digital Display The indicator will light up when the cleaner is in Eco Mode The indicator will light up when the cleaner is in Max Mode. The Digital Display shows the time or the fault code The fault code is displayed to help identify the problem The indicator will flash RED when Waste Water Tank is full. The indicator will flash RED when Clean Water Tank needs clean water. The indicator will light up WHITE when the cleaner is in Self-cleaning Mode.
Product Assembly To assemble, insert the Handle into the Main Body until you hear a click that will confirm the Handle is in place. To remove the Handle, insert a screwdriver or Allen key into the small hole located at the back of the Main Body and press while lifting the Handle up. Pull out the Clean Water Tank from the Main Body. Lift open the top cover of the tank, fill with tap water, close cover firmly and replace in the Main Body so it clicks into place.
Place the Waste Water Tank at an angle at the base of the Main Body and then push into place, ensuring that you hear a click confirming that it has been correctly installed. Install the Roller Brush or Carpet Brush by aligning the groove on the right side of the brush with the drive shaft and then press down on the Roller or Carpet Brush. Then attach the Window Cover by snaping on the side buckles and latch, ensuring you hear a click confirming correct installation.
Charging Insert the Adapter into the Charging Station port and plug the other end into the power outlet. Ensure that the Power button is off. Place the Vacuum Sweeper Mop Main Body onto the Charging Station ensuring that there is a battery connection and the unit can start charging.
Operation Operate the Vacuum Sweep Mop by following these steps: Remove the Vacuum Sweep Mop from the Charging Station. Place on the floor and press the Power button. Press the Mode button to select either Eco or Max. Press the Voice on or off setting at the back of the unit. Voice on will direct you on how to operate, clean, etc. Ensure that the Clean Water Tank is full and the Waste Water Tank is empty before starting to use the appliance.
Cleaning and Maintenance Routine Cleaning After each use, the appliance needs to be cleaned. Place the Main Body onto the Charging Station. Ensure the Clean Water Tank is full and press the Self-Clean button. During the cleaning process the display time on the display will count down from 59 to 0 seconds. After self-clean is complete, unplug the appliance and remove the Waste Water Tank. Empty the waste water and debris, rinse the container, and replace it in the Main Body.
Troubleshooting Does not charge ·Check if the Adapter Plug is connected to the power source. ·Check if there is water or foreign object on the magnetic connector of the Adapter. Please wipe it dry and clean. ·Check if the Main Body and the Charging Station are properly connected. Appliance does not start ·The battery is low. Please charge it. ·The Roller or Roller Brush is stuck. Please open the Window Cover to clean the parts.
Appliance doesn't move smoothly ·The Roller Brush or Carpet Brush are not installed correctly Self-clean doesn't work ·Wastewater tank is full ·No water in clean water tank Wastewater overflows ·Check if the wastewater tank is full. Error Code Table The error code is displayed on the LED Display, which helps to identify the problem. The causes and the possible solutions are provided below.
Lead This form is prepared in accordance with SJ/T 11364-2014. O Means that the content of hazardous substance in all materials of the part is below the limit requirements specified in GB/T 26572-2011. X Means that the content of the hazardous substance in the last one homogeneous material of the part. Exceeds the limit requirements specified in GB/T. 26572-2011. X Parts shows that due to the current technical and technological level restrictions.
