User Manual

ManualsBrandsEPV Projection Screens ManualsElectronicsPrime Vision 110" Projector Screen (Chroma White)

JA-022818 www.EPVscreens.com 1

Matte White Fixed Frame Projection Screen

Prime Vision ISF Series

User’s Guide

Thank you for choosing the Prime Vision ISF fixed frame projection screen! The Prime Vision ISF Series by

EPV Screens® leads the industry in quality fixed frame projection screens. Its design features a 2.4” wide

frame with velvet coating that frames its ISF Certified ChromaWhite screen material. The ChromaWhite is

specially formulated to provide diffusion uniformity with accurate color reproduction for a flat spectral

response in a controlled room environment.

Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a

long product life.

Care & Use Instructions: Dust, dirt and scratches on the projection surface will affect the picture

quality, please take note of the points below to prevent that from occurring:

1. Do not touch the projection surface with your hands

2. Do not write or draw on the projection surface

3. Do not use fingers or sharp objects to point on the projection surface.

4. Use clean water when dampening the cleaning cloth and do not rub against the material.

5. Do not use chemical cleaning agents or alcohol to clean the screen material.

Note: Please make sure all parts are included in your package before assembling your Prime Vision ISF

fixed frame projection screen.

Hardware and Parts List

A. Frame Parts x 6 pcs

(4 top/bottom frame pcs + 2 side frame pcs)

H. M5x15 screw x 16 pcs

B. ChromaWhite Screen Material x 1 pc

I. Center Support Bar x 1 - 2 pcs

(depending on model/size)

C. Center joint x 2 pcs

J. Support joiner x 2 - 4 pcs (depending on model/size)

(Install into the support bar before shipment)

D. Elbow Joint x4 pcs

K. Fix Plates x 60 - 180 pcs

(depending on model/size)

E. Wall bracket x 4 pcs

L. Rubber mallet x 1 pc

F. Wood screw x 8 pcs

M. Screw driver x 1 pc

G. Hollow wall anchor x 8 pcs

Summary of content (7 pages)

PAGE 1
Matte White Fixed Frame Projection Screen Prime Vision ISF Series User’s Guide Thank you for choosing the Prime Vision ISF fixed frame projection screen! The Prime Vision ISF Series by EPV Screens® leads the industry in quality fixed frame projection screens. Its design features a 2.4” wide frame with velvet coating that frames its ISF Certified ChromaWhite screen material.
PAGE 2
FRAME ASSEMBLY 1. Insert the center joint (c) connector to the horizontal frame piece with bevel connection and flat head, and then fasten it with two M5x15 screws (h). ½ Long Frame M5x15 Screw bevel connection Flat head 2. Insert the other horizontal frame piece to the center joint connector and then fasten it with two M5x15 screws. Flat head ½ Long Frame Push ×2 Bevel connection Horizontal Long Frame Note: a. 2 long frames should be assembled for a screen. b.
PAGE 3
Push Push Short frame Short frame (Fig.1.1) Screw M5×15Screws (Fig.1.2) ( fig.3) 4. Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembled, please push simultaneously the two ends of the long frames. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push M5x15 screws Screw ( fig.2) ( fig.3) JA-022818 www.EPVscreens.
PAGE 4
Attaching the Screen Material to the Frame 1. Make sure the screen material and frame are both lying face down on a clean, dry, and non-abrasive surface. 2. Carefully unroll the material inside the frame. (Fig.3) Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a sufficient amount of tension for perfect material flatness. Notes： (Fig.3) • Make note of the label to help distinguish the back and front side.
PAGE 5
Tip for attaching the last corner (D): 1. Position yourself left of location ①. 2. Pull the material to the corner of the frame with your hand while your left ③ Pull hand snaps in the fix plate on location ① (the third red dot). ④ 3. Then insert and snap in the fix plate on location ②. 4. Next, move and position yourself on location ③，then pull the edge to the frame and fasten plates on locations ③ and ④. ① 5. Finally, fasten the last fix plate on location ⑤. (Fig.8) ② ⑤ (Fig.
PAGE 6
Center Support Bar Installation 1. Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where the fix plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove (see Fig. 17 below for details). Diagonal models bleow 165” use 1 x Center Support Bar Remove Center Support Bar push Center Support Bar Fixed plate groove (Do not insert here) (Fig.
PAGE 7
Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. Note: Use 2 top wall brackets on diagonal sizes below 135”, and use 3 top wall brackets on diagonal sizes 135” and above. 4.