Installation Manual

ManualsBrandsEpson ManualsOffice ElectronicsExpression Home Wireless Color Printer with Scanner and Copier

Start Here

9 Follow the on-screen instructions to adjust the print

quality of your product.

Note:

• You need to load paper before you can adjust the print quality.

See “Load paper” below for details.

• Select Adjust Later if you want to adjust the print quality later.

For more information, see the online User’s Guide.

Load paper

See the online User’s Guide for information about loading

capacity, available paper types and sizes, and loading

envelopes.

1 Make sure the product is not charging. Then ﬂip the

feeder guard forward, raise the paper support, and tilt it

backwards slightly.

2 Slide the edge guides all the way out.

3 Load paper, glossy or printable side up and short edge

ﬁrst, in the middle of the rear paper feed slot.

4 Slide the edge guides against the paper, but not too

tightly.

5 Pull out the output tray.

6 Follow the instructions on the LCD screen to select your

paper settings.

IMPORTANT: Before using this product, make sure you read

these instructions and the safety instructions in the online

User’s Guide.

Note: This printer is designed for use with Epson

cartridges only, not

third-party cartridges or ink. For important ink information, visit

www.epson.com/epsonink (U.S.) or www.epson.ca/epsonink (Canada)

or see your printer box.

Unpack

Note: Do not open ink cartridge packages until you are ready to install

the ink. Cartridges are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

2 Lift up the scanner unit until it locks into place and

remove all protective materials from inside the product.

Caution: Do not touch the ﬂat white cable.

3 Lift the scanner unit up slightly and lower it. When

the scanner unit catches, lift it up again and lower it

completely.

Turn on and configure

1 Connect the power cord to the back of the product and to

an electrical outlet.

Caution: Do not connect to your computer yet.

2 Raise the control panel and turn on the product.

3 Press or to select your language, then press OK.

Note: You can change the language later using the product’s

control panel. For more information, see the online User’s Guide.

Install ink cartridges

Caution: Keep ink cartridges out of the reach of children and do not

drink the ink.

Note: The included initial cartridges are designed for reliable printer

setup and cannot be used as replacement cartridges or resold. After

setup, the remaining ink is available for printing.

1 Lift up the scanner unit until it locks into place.

2 Gently shake the black ink cartridge.

Note: Do not shake the other ink cartridges.

3 Unpack the ink cartridges.

4 Remove only the yellow tape from each ink cartridge.

Caution: Do not remove any other labels or seals, or ink will

leak. Do not touch the green chip on the cartridge.

5 Insert the cartridge in the holder for each color. Press each

cartridge down until it clicks. Make sure all cartridges are

pushed down into place.

6 Lift the scanner unit up slightly and lower it. When

the scanner unit catches, lift it up again and lower it

completely.

7 Press OK to start charging the ink delivery system.

8 The printer starts charging the ink. Ink charging takes

approximately 6 minutes. When you see a completion

message on the printer’s LCD screen, charging is

complete.

Caution: Don’t turn off the printer or raise the scanner unit while

it is charging or you’ll waste ink.

Note: As part of setup, your product’s serial number will be sent

to a secure Epson server so that you can be eligible to participate

in programs we may offer from time to time, including the Epson

ink replenishment program. You will have a separate opportunity

to consent to participating in such programs.

XP-4100/XP-4105

Summary of content (4 pages)

PAGE 1
XP-4100/XP-4105 3 Start Here ift the scanner unit up slightly and lower it. When L the scanner unit catches, lift it up again and lower it completely. 2 Gently shake the black ink cartridge. 9 ollow the on-screen instructions to adjust the print F quality of your product. Note: • Y ou need to load paper before you can adjust the print quality. See “Load paper” below for details. • Select Adjust Later if you want to adjust the print quality later.
PAGE 2
XP-4100/XP-4105 3 Start Here ift the scanner unit up slightly and lower it. When L the scanner unit catches, lift it up again and lower it completely. 2 Gently shake the black ink cartridge. 9 ollow the on-screen instructions to adjust the print F quality of your product. Note: • Y ou need to load paper before you can adjust the print quality. See “Load paper” below for details. • Select Adjust Later if you want to adjust the print quality later.
PAGE 3
5 Install software Note: • If you are using a Mac or your computer does not have a CD/DVD drive, an Internet connection is required to obtain the product software. • T o print from a Chromebook™, go to www.epson.com/support/gcp (U.S.) or www.epson.ca/support/gcp (Canada) for instructions. Firmware Update Notice: Epson periodically provides firmware updates to address issues of security, performance, minor bug fixes and ensure your printer functions as designed.
PAGE 4
5 Install software Note: • If you are using a Mac or your computer does not have a CD/DVD drive, an Internet connection is required to obtain the product software. • To print from a Chromebook™, go to www.epson.com/support/gcp (U.S.) or www.epson.ca/support/gcp (Canada) for instructions. Firmware Update Notice: Epson periodically provides firmware updates to address issues of security, performance, minor bug fixes and ensure your printer functions as designed.