BrightLink® 685Wi/695Wi User's Guide
Contents BrightLink 685Wi/695Wi User's Guide..................................................................................................... 11 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents.....................................................
Connecting to a Computer for Sound........................................................................................ Connecting to Video Sources ........................................................................................................ Connecting to an HDMI Video Source ...................................................................................... Connecting to an MHL-Compatible Device ...............................................................................
Network Projector E-mail Alert Messages ..................................................................................... Setting Up Monitoring Using SNMP ................................................................................................... Controlling a Networked Projector Using a Web Browser .................................................................. Crestron RoomView Support...........................................................................................................
Supported PC Free File Types .................................................................................................... Starting a PC Free Slide Show .................................................................................................... Starting a PC Free Movie Presentation ....................................................................................... PC Free Display Options .....................................................................................................
Using the Interactive Features ............................................................................................................... 148 Interactive Modes............................................................................................................................. 148 Using the Projected Screen as a Whiteboard (Built-in Whiteboard Mode)................................... 149 Drawing on a Projected Image (Built-in Annotation Mode) .....................................................
Adjusting the Menu Settings .................................................................................................................. Using the Projector's Menus............................................................................................................. Image Quality Settings - Image Menu .............................................................................................. Input Signal Settings - Signal Menu..................................................................
Solutions When "No Signal" Message Appears........................................................................... 249 Displaying From a PC Laptop ................................................................................................. 250 Displaying From a Mac Laptop ............................................................................................... 250 Solutions When "Not Supported" Message Appears ...................................................................
Projector Environmental Specifications............................................................................................ Projector Safety and Approvals Specifications................................................................................. Supported Video Display Formats.................................................................................................... USB Display System Requirements ..........................................................................................
BrightLink 685Wi/695Wi User's Guide Welcome to the BrightLink 685Wi/695Wi User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Flexible connectivity • Three HDMI ports (one with MHL support) for computer or video device connection • Plug-and-play 3-in-1 USB projection, audio, and mouse control for instant setup • Wired network support for projection • Projector monitoring and control via remote network computer • Optional wireless network support, including video and audio transfer • PC Free photo slide shows via connected USB memory devices or Epson document camera • Dual VGA ports for connections by multiple presenters • Port for
Related concepts Projector Part Locations Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
1 Projector 2 Remote control 3 Remote control batteries (two AA alkaline) 4 Pens and replacement pen tips (two hard tips and four soft tips) 5 Battery charger and two rechargeable batteries 6 Pen tray 7 USB cable 8 Power cord 9 USB extension cable 10 Touch Unit connection cable (BrightLink 695Wi) 11 Password Protected sticker 12 Projector manuals and software download links CD 13 Projector software for Easy Interactive Function CD 14 Touch Unit (BrightLink 695Wi) 15 Markers (x2)
Unless listed as available from Epson in this table, see your local computer or electronics dealer for purchase information. Signal or connection type Additional component necessary Composite video RCA-style video or A/V cable Component video D-sub, 15-pin, component-to-VGA video cable or adapter Available for purchase from Epson or an authorized Epson reseller. HDMI Compatible HDMI cable Available for purchase from Epson or an authorized Epson reseller.
Projector software Manual Description EasyMP Monitor (Windows only) EasyMP Monitor Operation Guide Lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector. EasyMP Multi PC Projection EasyMP Multi PC Projection Operation Guide Lets you hold interactive meetings by projecting the computer screens of users over a network.
Option or part Part number Genuine Epson replacement lamp (ELPLP91) V13H010L91 Replacement air filter (ELPAF49) V13H134A49 Wireless LAN module (ELPAP10) V12H731P02 Additional interactive pen A (ELPPN05A) (orange) V12H773010 Additional interactive pen B (ELPPN05B) (blue) V12H774010 Replacement set of hard pen tips (ELPPS03) V12H775010 Replacement set of soft pen tips (ELPPS04) V12H776010 Ultra-short throw wall mount (ELPMB46) V12H777020 Table projection mount (ELPMB29) V12H516020 Epson DC
In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details. Register your product online using the projector CD or at this site: epson.com/webreg. Registering also lets you receive special updates on new accessories, products, and services.
Projector Parts - Front/Top Projector Parts - Side Projector Parts - Interface Panel Projector Parts - Base Projector Parts - Control Panel Projector Parts - Interactive Pens and Pen Tray Projector Parts - Remote Control Projector Parts - Touch Unit Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Remote control receiver 2 Speaker 3 Control panel 20
4 Cable cover 5 Exhaust vent 6 Lamp screws 7 Lamp cover screw 8 Lamp cover Parent topic: Projector Part Locations Projector Parts - Side 1 Air filter cover switch 2 Wireless LAN light 3 Interactive pen receiver 4 Obstacle sensors 5 Remote receiver 21
6 Projection window 7 Security lock port 8 Air filter cover 9 Air intake vents (air filter) 10 Focus lever Parent topic: Projector Part Locations Projector Parts - Interface Panel 1 Optional wireless LAN module slot 2 Audio1 port 3 Computer1 port 4 Audio2 port 5 USB-B port 6 Network (LAN) port 7 HDMI 1/MHL port 22
8 Monitor Out/Computer2 port 9 HDMI 2 port 10 HDMI 3 port 11 RS-232C port 12 SYNC In/Out port 13 Power inlet 14 Touch unit (TCH) port (BrightLink 695Wi) 15 USB-A port 16 Video port 17 Audio port 18 Audio Out port 19 Mic (microphone) port Parent topic: Projector Part Locations Related references Projector Light Status 23
Projector Parts - Base 1 Ceiling mount holes (5) 2 Security cable attachment point 3 Rear foot holes 4 Wall mount plate holes (4) 5 Illumination sensor 6 Front foot hole Parent topic: Projector Part Locations 24
Projector Parts - Control Panel 1 Source Search button (searches for connected video sources) 2 Enter button (selects options) 3 Horizontal/Vertical keystone adjustment buttons (display the adjustment screen and adjust screen shape) and arrow buttons 4 Esc button (cancels/exits functions) 5 W/T buttons (Wide/Tele; adjust projected image size) and arrow buttons 6 Menu button (accesses projector menu system) 7 Home button (displays home screen) 8 Power button 9 Projector status lights (power
Projector Parts - Interactive Pens and Pen Tray 1 Pen tip 2 Battery light 3 Function button 4 Attachment for optional strap or cord 26
5 Battery cover 1 Installation magnets 2 Mounting holes 3 Security lock hole Parent topic: Projector Part Locations 27
Projector Parts - Remote Control 28
1 Power button 2 Computer button (cycles through connected computer sources) 3 HDMI/Video button (cycles through connected HDMI/video sources) 4 Numeric buttons (enter numbers) 5 Auto button (automatically adjusts position, tracking, and sync settings) 6 Aspect button (selects the image aspect ratio) 7 Num button (when held down, switches numeric buttons to number function) 8 Menu button (accesses projector menu system) 9 Arrow buttons (move through on-screen options and control wireless mo
28 Source Search button (searches for connected sources) Parent topic: Projector Part Locations Projector Parts - Touch Unit The Touch Unit comes with the BrightLink 695Wi projector only.
6 Mounting holes Rear 1 Laser diffusion ports 2 Installation magnets Parent topic: Projector Part Locations 31
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Removing and Attaching the Cable Cover Projector Connections Installing Batteries in the Remote Control Installing Batteries in the Pens Projector Placement Your ultra-short throw projector is designed to be installed on a wall (with a wall mount) or vertically on a table (with a table mount) to create an interactive tabletop workspace.
Projector Setup and Installation Options You can set up or install your projector in the following ways: Mounted on the wall or ceiling Mounted vertically on a table to create an interactive workspace Front projection from a table or portable cart (BrightLink 685Wi) 33
Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an angle. If you project from a table or portable cart, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
1. Use a screwdriver to remove both of the cable cover screws. 2. Slide off the cable cover.
To attach the cable cover, slide it into position and tighten the screws with a screwdriver. Parent topic: Setting Up the Projector Projector Connections See these sections to connect the projector to a variety of projection sources. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
Connecting to a Computer for USB Video and Audio If your computer meets the system requirements, you can send video and audio output to the projector through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a USB cable. Note: This also lets you use the interactive pens with your computer. You need to change the USB Type B setting in the projector's Extended menu before you can project through the USB port.
• Mac: The USB Display setup folder appears on your screen. Select USB Display Installer and follow the on-screen instructions to install the Epson USB Display software. Follow any on-screen instructions. You need to install this software only the first time you connect the projector to the computer. The projector displays the image from your computer's desktop and outputs sound, if your presentation contains audio.
Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port. 1.
2. Connect the USB cable to your projector's USB-B port. 3. Connect the other end to any available USB port on your computer. 4. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details.
2. Connect the other end to the Audio port that corresponds to the Computer port you are using. Parent topic: Connecting to Computer Sources Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
2. Connect the other end to one of the projector's HDMI ports. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers.
3. Connect the other end of the cable to the projector's HDMI 1/MHL port. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers. Parent topic: Connecting to Video Sources Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable.
Note: If you choose the Computer2 port, you may need to change the Monitor Out Port setting in the projector's Extended menu. 3. Tighten the screws on the VGA connector. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Signal menu.
1. Connect the audio cable to your video source's audio-out ports. 2. Connect the other end of the cable to the projector's Audio port that corresponds to the port you are using for video. Parent topic: Connecting to Video Sources Connecting to an External Computer Monitor If you connected a computer to the projector's Computer port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible.
2. Connect the external monitor's cable to your projector's Monitor Out/Computer 2 port. Note: You may need to change the Monitor Out Port setting in the projector's Extended menu and restart the computer. Note: Content you draw using the interactive features is not displayed on an external monitor unless you draw it using Easy Interactive Tools.
3. Connect one end of the cable to your external speakers as necessary. 4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting a Microphone You can connect a microphone to the projector's Mic port to provide audio support during presentations .
1. Connect the microphone cable to the projector's Mic port. 2. Turn on the microphone, if necessary. 3. If you hear a crackling noise or the volume is too high or low, adjust the Mic Input Level setting in the Settings menu. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
• USB hard drive • Multimedia storage viewer Note: Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices, and must be USB Mass Storage Class-compliant.
Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly. 3. Connect the other end of the cable (if applicable) to your device. Parent topic: Connecting to External USB Devices Related topics Projecting a PC Free Presentation Selecting the Connected USB Source You can switch the projector's display to the source you connected to the USB-A port. 1. Make sure the connected USB source is turned on, if necessary. 2.
• For the Epson DC-21 document camera, connect it to the projector's HDMI, Computer, or Video port and to the corresponding port on the document camera. See the document camera manual for details. Note: For additional features supported by software, connect your document camera to your computer instead of the projector. See the document camera manual for details.
Note: If you are connecting three or more projectors, connect the projectors in a chain as shown. 2. In the Extended menu, set the Sync of Projectors setting to Wired. Note: If you are using the projector in the same room as another projector that does not support cable connection or if you do not have the optional remote control cable or a stereo mini cable, set the Wired Sync Mode setting to Mode 2 in the projector's Extended menu.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Setting Up the Projector Installing Batteries in the Pens Each pen uses one AA battery.
1. Open the battery cover as shown. 2. Insert the battery with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic: Setting Up the Projector 55
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Note: The interactive features may be slower over a network connection than over a USB connection. Wired Network Projection Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Crestron RoomView Support Wired Network Projection You can project through a wired network.
2. Connect the other end of the cable to the projector's LAN port. Parent topic: Wired Network Projection Selecting Wired Network Settings Before you can project from computers on your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in Epson Web Control. (Default user name is EPSONREMOTE; default password is guest.) • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
8. If necessary, select IP Settings and press Enter. 9. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting. • If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter.
Related references Projector Network Settings - Network Menu Additional Projector Software and Manuals Projector Network Settings - Network Menu Installing the Wireless LAN Module To use the projector over a wireless network, install the Epson 802.11b/g/n wireless module in the projector. Do not install any other type of wireless module. Caution: Never remove the module while its indicator light is blue or flashing, or while you are projecting wirelessly. You may damage the module or lose data.
2. Unscrew and remove the cable cover if it is attached (screwdriver not included).
3. Insert the wireless LAN module into the port shown here. 4. Replace the cable cover and tighten the screws. 5. Plug in and turn on the projector. Parent topic: Wireless Network Projection Using Quick Wireless Connection (Windows) You can create a Quick Wireless Connection USB Key to quickly connect the projector to a Windows computer wirelessly. Then you can project your presentation and remove the key when you are done. Note: A USB flash drive is not included with your projector. 1.
3. Insert the USB key into the projector's USB-A port. You see a projected message that the network information update is complete. 4. Remove the USB key. 5. Insert the USB key into a USB port on your computer. Note: In Windows Vista, if you see the AutoPlay window, select Run MPPLaunch.exe, then select Allow on the next screen. 6. Follow the on-screen instructions to install the EasyMP Multi PC Projection software. Note: If you see a Windows Firewall message, click Yes to disable the firewall.
Parent topic: Wireless Network Projection Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Make sure the Wireless Mode setting is set to Wireless LAN On. 5. Select Network Configuration and press Enter.
6. Select the Basic menu and press Enter. 7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in the Epson Web Control.
• Display LAN Info lets you select how the projector displays network information. You can select an option to display a QR code that lets you quickly connect your iOS or Android devices using the Epson iProjection app. Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press Enter to select them. 8. Select the Wireless LAN menu and press Enter. 9.
Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you quickly connect to multiple computers or devices directly or use a Quick Wireless Connection USB Key to connect Advanced: lets you connect to multiple computers or devices via a wireless network access point Search Access Point To Search View Search for available wireless network access points in Advanced connection mode SSID Up 32 alphanumeric characters
Setting Options Description IP Address Display On Selects whether to display the IP address on the network standby screen Off Parent topic: Selecting Wireless Network Settings Manually Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1. To access your wireless utility software, access the Desktop and double-click the network icon on the Windows taskbar. 2.
Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Wireless LAN menu and press Enter. 5. Select the Security setting and press Enter. 6. Select the security settings for your network. 7. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Wireless LAN menu and press Enter. 6. Select Connection Mode and press Enter. 7. Select Quick and press Enter, then press Enter again.
8. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. 9. Press the Home button on the projector or the remote control. 10. Select the QR code icon and press Enter. Your projector displays a QR code on the projection surface. 11. Open Epson iProjection on your smartphone or tablet. 12. Use the QR code reader feature to read the QR code and connect your device to the projector.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Notifications menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server setting. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7.
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
4. Select the Notifications menu and press Enter. 5. Turn on the SNMP setting. 6. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
7. Select the Others menu and press Enter. 8. If available, select the Priority Gateway setting for your network. 9. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected. 10. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView setting to allow the projector to be detected. 11.
Note: The web setup and control features support Microsoft Internet Explorer 9.0 or later, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser. Note: If you set Standby Mode to Communication On, you can use a web browser to select settings and control projection even if the projector is in standby mode. 1. Make sure the projector is turned on. 2.
You see a screen like this: 1 Power button control 2 Selects the Computer port source 3 Selects Video and HDMI port sources 4 Freeze button control 5 A/V Mute button control 6 Page Up and Page Down button controls 7 Searches for sources 8 Selects the network source 9 Selects the USB Display or USB device source 10 Volume button controls 11 Displays a QR code for connecting with iOS or Android devices using the Epson iProjection app 7.
Related references Projector Setup Settings - Extended Menu Crestron RoomView Support If you are using the Crestron RoomView network monitoring and control system, you can set up your projector for use on the system. Crestron RoomView lets you control and monitor your projector using a web browser. Note: You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP Monitor when you use Crestron RoomView. For additional information on Crestron RoomView, contact Crestron.
4. Select the Others menu and press Enter. 5. Set the Crestron RoomView setting to On to allow the projector to be detected. Note: Enabling Crestron RoomView disables the Epson Message Broadcasting feature in the EasyMP Monitor software. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Turn off the projector, then turn it on again to enable the setting.
You see this screen: 3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box. 4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons. You can scroll through button options at the bottom of the screen.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's power light turns blue. This indicates that the projector is receiving power. 3. Press the power button on the projector or the remote control to turn on the projector. The projector beeps and the Status light flashes blue as the projector warms up.
Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children. If you do not see a projected image right away, try the following: • Turn on the connected computer or video device. • Insert a DVD or other video media and press the play button, if necessary. • Press the Source Search button on the projector or remote control to detect the video source. • If the Home screen is displayed, select the source you want to project.
2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). 3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.
4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Related references Projector Setup Settings - Extended Menu Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen.
3. Press a keystone button on the projector's control panel to adjust the image shape. Note: The horizontal keystone adjustment buttons are labeled W and T. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the H/V-Keystone settings in the projector menus.
Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. Note: Adjusting the Quick Corner setting may affect interactive pen and finger touch calibration. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Press the Menu button.
3. Select the Settings menu and press Enter. 4. Select the Geometry Correction setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: Note: To reset your adjustments, press and hold the Esc button for at least 2 seconds to display a reset screen. Then select Yes.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. Press Enter to return to the area selection screen. 8. When you are finished, press Esc.
4. Select the Geometry Correction setting and press Enter. 5. Select the Arc Correction setting and press Enter. Then press Enter again. You see the Arc Correction adjustment screen. 6. Use the arrow buttons on the projector or the remote control to select the corner or side of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc.
3. To reduce the image size, press the T (Tele) button. After you adjust the image size, the Image Shift screen is displayed automatically for adjusting the image position. Note: If the projector is installed out of reach, you can also adjust the image size with the remote control using the Zoom setting in the projector menus.
1. Turn on the projector and display an image. 2. Adjust the image size using the W (Wide) and T (Tele) buttons. After you adjust the image size, the Image Shift screen is displayed automatically. 3. Use the arrow buttons on the projector or remote control to adjust the image position. Note: You can also use the Settings menu to adjust the Image Shift setting. Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Focusing the Image 1.
2. Slide the air filter cover latch and open the air filter cover. 3. Raise or lower the focus lever to sharpen the image.
Related references Projector Feature Settings - Settings Menu Remote Control Operation The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen or board, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the angles listed here. 1 19.
Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
4. Use the following buttons on the remote control to control your presentation: • To move through slides or pages, press the up or down Page buttons. • To move the cursor on the screen, use the arrow buttons. • To left-click, press the button once (press it twice to double-click). • To right-click, press the Esc button. • To drag-and-drop, hold the at the destination.
1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen. Parent topic: Remote Control Operation Related references Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
3. Do one of the following: • Press the Source Search button on the projector or remote control until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources. • Press the Home button on the remote control and select your image source.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front lets you project from a table in front of the screen. • Front/Upside Down (default setting) flips the image over top-to-bottom to project upside-down from a wall or ceiling mount. This mode should also be used when you mount the projector vertically on a table to create an interactive work surface.
The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for five seconds again. Parent topic: Projection Modes Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal and the Resolution setting. Normal Displays images using the full projection area and maintains the aspect ratio of the image. 16:9 Converts the aspect ratio of the image to 16:9.
1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode. The image appearance changes and the name of the Color Mode appears briefly on the screen. 4. To cycle through all the available Color Modes for your input signal, press the Color Mode button repeatedly.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button. 3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment.
Controlling the Volume with the Volume Buttons You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio. The volume buttons control the projector’s internal speaker system or any external speakers you connected to the projector. You must adjust the volume separately for each connected input source. 1. Turn on the projector and start a presentation that includes audio. 2. To lower or raise the volume, press the Volume buttons on the remote control.
Related tasks Connecting a USB Device or Camera to the Projector Supported PC Free File Types You can project these types of files using the projector's PC Free feature. Note: For best results, place your files on media that is formatted in FAT16/32. If you have trouble projecting from media formatted for non-Windows file systems, try formatting the media for Windows instead. You may not be able to use the security features on certain USB storage devices with PC Free features.
Starting a PC Free Slide Show After connecting a USB device or digital camera to the projector, you can switch to the USB input source and start your slide show. Note: You can change the PC Free operation options or add special effects by highlighting Option at the bottom of the screen and pressing Enter. Note: You can also use the interactive pen or your finger (BrightLink 695Wi)to operate the slide show. 1. Press the USB button on the projector remote control. The PC Free screen appears. 2.
• To view additional files in a folder, highlight Next page or Previous page and press Enter. (You can also press the Page up or down buttons on the remote control.) 3. Do one of the following: • To display an individual image, press the arrow buttons to highlight the image and press Enter. (Press the Esc button to return to the file list screen.) • To display a slide show of all the images in a folder, press the arrow buttons to highlight the Slideshow option at the bottom of the screen and press Enter.
Starting a PC Free Movie Presentation After connecting a USB device or digital camera to the projector, you can switch to the USB input source and start your movie. Note: You can change the PC Free operation options by highlighting Option at the bottom of the screen and pressing Enter. 1. Press the USB button on the projector remote control. The PC Free screen appears. 2.
3. To play back a movie, press the arrow buttons to highlight the file and press Enter. Note: If any file names are longer than 8 characters or include unsupported symbols, the file names may be shortened or changed only in the screen display. If you want to play back all the movies in a folder in sequence, select the Slideshow option at the bottom of the screen. 4. To stop movie playback, press the Esc button, highlight Exit, and press Enter.
Setting Options Description Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically; high resolution images may switch at a slightly slower rate Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variety of effects Parent topic: Projecting a PC Free Presentation
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
• E-Zoom • Switching aspect mode • Operations made by the User button on the remote control • Auto Iris Note: You cannot project from the same input source onto both sides (left and right) of the screen. You also cannot use split screen with certain input source combinations. 1. Press the Split button on the remote control. The currently selected input source moves to the left side of the screen. 2. Press the Menu button.
You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter, select the input source, select Execute, and press Enter. (You can also change image sources, if necessary.) 4. To switch the images, select the Swap Screens setting and press Enter. 5. To change the image sizes, select the Screen Size setting, press Enter, select a sizing option, press Enter, and press Menu to exit.
Input Sources for Split Screen Projection You can choose from the input source combinations listed here for split screen projection.
Projector Identification System for Multiple Projector Control You can operate multiple projectors using one remote control for more elaborate presentations. To do this, you assign an identification number to each projector and to the remote control. Then you can operate all the projectors at once or individually. Note: In some cases the brightness and color tone from different projectors may not match completely even after color correction.
Note: If you don't know the projector's ID, aim the remote control at the projector and press the ID button to temporarily display the projector's ID on the screen. Parent topic: Using Multiple Projectors Related references Projector Setup Settings - Extended Menu Setting the Remote Control ID The remote control's ID is set to zero by default so it can operate any compatible projector.
Note: • You must set the remote control ID to match the projector ID each time you turn on the projector you have set it to control. • When you select 0 on the remote control, you can operate all projectors regardless of the Projector ID setting. • If you turn off the Projector ID setting, the remote control will operate the projector regardless of the ID selected on the remote.
2. Select the Multi-Projection setting and press Enter. 3. Select the Color Uniformity menu and press Enter. 4. Select the Color Uniformity setting and press Enter. 5. Set the Color Uniformity setting to On and press Enter, then press Esc. 6. Select Adjustment Level and press Enter. 7. Select an adjustment level and press Esc. 8. Select Start Adjustments and press Enter. 9. Select the area you want to adjust and press Enter.
10. Select Red, Green, or Blue and use the left arrow button to weaken the color tone and the right arrow button to strengthen the color tone. Note: The adjustment screen changes each time you press Enter. 11. Press Esc to return to the area selection screen. 12. Repeat steps 9 through 11 for each area. 13. Press Esc to return to the previous screen.
4. Select the Extended menu and press Enter. 5. Select the Multi-Projection setting and press Enter.
6. Select the Brightness Level setting and press Enter. 7. Select a brightness level and press Enter. 8. Press Esc to return to the previous screen. Parent topic: Using Multiple Projectors Related references Projector Setup Settings - Extended Menu Matching the Image Colors You can match the display quality of multiple projectors that will project next to one another. Note: This function is disabled in the built-in whiteboard mode.
1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Multi-Projection setting and press Enter. 4. Select the Color Matching setting and press Enter. 5. Select the Adjustment Level setting and press Enter.
You see this screen: 6. Press the left or right arrow buttons to select a value for the Adjustment Level setting. Note: There are six adjustment levels ranging from white to black and you can adjust each level individually. 7. Press the left or right arrow buttons to adjust the color tone for the Red, Green, and Blue settings. 8. Press the left or right arrow buttons to adjust the Brightness setting. 9. Repeat the previous three steps as necessary to adjust each adjustment level.
2. Select the Extended menu and press Enter. 3. Select the Multi-Projection setting and press Enter.
4. Select the RGBCMY setting and press Enter. 5. Select the color to adjust and press Enter. • To adjust the overall hue of the color, adjust the Hue setting. • To adjust the overall vividness of the color, adjust the Saturation setting. • To adjust the overall brightness of the color, adjust the Brightness setting. You see this screen: 6. Press the left or right arrow buttons to adjust the color tone for the Hue, Saturation, and Brightness settings. 7.
Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. If you want to display an image such as a company logo or picture when the presentation is stopped, you can set up this feature using the projector's menus. 1.
1. Press the Freeze button on the remote control to stop the video action. 2. To restart the video action in progress, press Freeze again. Parent topic: Adjusting Projector Features Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. Note: You can also zoom into your image using the interactive pens.
1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into. • Press the E-Zoom + button repeatedly to zoom into the image area, enlarging it as necessary. Press and hold the E-Zoom + button to zoom in more quickly.
Password Security Types You can set up these types of password security using one shared password: • Power On Protection password prevents anyone from using the projector without first entering a password. • User's Logo Protection password prevents anyone from changing the custom screen the projector can display when it turns on or when you use the A/V Mute feature. The presence of the custom screen discourages theft by identifying the projector’s owner.
4. Press and hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again. You see the message "Password accepted." 6. Press Esc to return to the menu. 7. Make a note of the password and keep it in a safe place in case you forget it.
Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for about seconds or until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On, press Enter again, and press Esc. 2.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector. You must enter the correct password to use the projector. 1. Press and hold down the Num button on the remote control while you enter the password using the numeric buttons. The password screen closes.
2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password three times in succession, you see a message telling you that the projector is locked. The projector will remain in standby mode for 5 minutes. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to enter the password.
2. Press the Menu button, select the Extended menu, and press Enter. 3. Select the User's Logo setting and press Enter. You see a prompt asking if you want to use the displayed image as a user's logo. 4. Select Yes and press Enter. You see a selection box overlaying your image. 5. Use the arrow buttons on the remote control to surround the image area you want to use as the User's Logo and press Enter. You see a prompt asking if you want to select this image area. 6. Select Yes and press Enter.
You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12. Select when you want to display the User's Logo screen: • To display it whenever there is no input signal, select Display Background and set it to Logo.
1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select Lock Setting and press Enter. 4. Select the Control Panel Lock setting and press Enter. 5. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 6. Select Yes and press Enter.
• Use the security slot on the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture. Note: Do not pass drop-prevention cables through the security cable attachment point when mounting the projector on a wall or ceiling.
2. Press the Menu button, select the Settings menu, and press Enter. 3. Select the Pattern setting and press Enter. 4. Select the User Pattern setting and press Enter. You see a prompt asking if you want to use the displayed image as a User Pattern. 5. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished. You see a completion message. 6.
Caution: If the copy process fails due to a power failure, communication error, or for any other reason, Epson will not be responsible for any repair costs incurred. The following settings will not transfer between projectors: • Info menu items • Network menu settings other than those in the Notifications and Others menus Note: In addition to the methods covered this section, you can also copy and transfer settings to multiple projectors over a network using the EasyMP Network Updater software.
2. Insert the flash drive into the USB-A port. Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly. 3. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When the power, Status, Lamp, and Temp lights turn on, release the Esc button. The lights flash to indicate that settings are transferring to the flash drive.
Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have to repeat your adjustments. 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Insert the flash drive into the USB-A port. Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly. 3.
Your computer must be running one of the following operating systems: • Windows Vista • Windows 7 • Windows 8.x • Windows 10 • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.x • macOS 10.12.x 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's USB-B port. 3. Connect the other end to any available USB port on your computer. 4.
7. Once the file has copied, do one of the following: • Windows: Open the My Computer, Computer, or Windows Explorer utility. Right-click the name of your projector (listed as a removable disk) and select Eject. • Mac: Drag the removable disk icon for your projector from the desktop into the trash. The projector enters standby mode.
6. Copy the pjconfdata.bin file from your computer to the removable disk. Note: Do not copy any other files to the removable disk. 7. Once the file has copied, do one of the following: • Windows: Open the My Computer, Computer, or Windows Explorer utility. Right-click the name of your projector (listed as a removable disk) and select Eject. • Mac: Drag the removable disk icon for your projector from the desktop into the trash.
Using the Interactive Features Follow the instructions in these sections to use your projector's interactive features. Interactive Modes Using the Interactive Pens Using Finger Touch Interactivity Using BrightLink with a Computer Windows Pen Input and Ink Tools Using BrightLink Without a Computer Interactive Modes The BrightLink interactive features turn any wall into an interactive whiteboard, either with or without a computer.
Related concepts Using BrightLink with a Computer Using BrightLink Without a Computer Using the Projected Screen as a Whiteboard (Built-in Whiteboard Mode) You can use the interactive pens or your finger (BrightLink 695Wi) to write or draw on the projection surface just as you would on a chalkboard or dry erase board. You can use one pen, both pens at the same time, or a combination of pens and finger touch (BrightLink 695Wi). 1.
3. To close the main toolbar, select the icon at the bottom of the toolbar. Note: If you want to hide the toolbar automatically after drawing, select the the toolbar. 4. To show or hide the projection control toolbar, select the icon at the bottom of arrow. Note: You can also show or hide the projection control toolbar from the projector's Display menu.
You see the main toolbar on the side and the projection control toolbar on the bottom of the projected image. 3. To move the main toolbar to the other side of the screen, tap the the screen. arrow on the opposite side of Note: You can use the pen or your finger (BrightLink 695Wi) to move the arrow icon up or down to reposition the toolbar. 4.
5. To close the main toolbar, select the icon at the bottom of the toolbar. Note: If you want to hide the toolbar automatically after drawing, select the the toolbar. 6. To show or hide the projection control toolbar, select the icon at the bottom of arrow.
4. Select the USB Type B setting and press the Enter button. 5. Select one of the following: • Easy Interactive Function to use PC Interactive mode. • USB Display/Easy Interactive Function to use PC Interactive mode and USB Display. • Wireless Mouse/USB Display to use the mouse and USB Display. 6. Press the Esc button to exit the USB Type B menu. 7. Select the Easy Interactive Function setting and press the Enter button.
8. Select one of the following as the Pen Operation Mode depending on the operating system your computer is using: • Windows/Mac Mode: Windows or Mac • Ubuntu Mode: Ubuntu 9. Press the Enter button and press the Menu button to exit the Extended menu. 10. Hover near or tap on the board or the projected image with the interactive pen or your finger (BrightLink 695Wi). The icon is displayed on the projected screen. 11. Select the icon, then select the icon.
Requirement Windows Mac Hard disk space 100MB or more Display Resolution between 1024 × 768 and 1920 × 1200, 16-bit color or greater Parent topic: Controlling Computer Features from a Projected Screen (PC Interactive Mode) Related concepts Easy Interactive Tools Using the Interactive Pens Follow the instructions in these sections to use the interactive pens.
Note: The pen turns off automatically after 15 seconds of inactivity. Hold the pen to turn the pen back on. 1 Pen tip 2 Battery light 3 Function button 4 Attachment for optional strap or cord 5 Battery cover • To turn on the pen, move the pen. Note: If you press the function button, the battery light flashes briefly, then turns off. If the battery is low, the battery light flashes continuously.
• For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the black section near the tip of the pen. • To write or draw on the projection surface in built-in annotation mode or built-in whiteboard mode, do the following: • To select a projected item, such as an icon, tap the projection surface with the pen tip. • To draw on the projected screen, tap the projection surface with the pen and drag it as necessary.
• To use the pen as a mouse in PC Interactive mode, do the following: • To left-click, tap the board with the pen tip. • To double-click, tap twice. • To right-click, press the button on the side. • To click and drag, tap and drag with the pen. • To move the cursor, hover over the board without touching it. Note: You can turn off the hovering feature using the Hovering setting in the projector's Easy Interactive Function menu.
If you notice positioning discrepancies after doing any of the following, calibrate again: • Performing Geometry Correction • Adjusting the image size • Using the Image Shift feature • Moving the projector Note: Move any pen you are not using away from the projection screen while calibrating. Calibrating Automatically Calibrating Manually Parent topic: Using the Interactive Pens Calibrating Automatically You do not need the pens or a computer for Auto Calibration.
2. Select the Easy Interactive Function setting and press Enter. 3. Select Auto Calibration and press Enter. 4. Adjust the image focus, if necessary. 5. Press Enter to select Yes. A pattern appears then disappears, and the system is calibrated. If you see a message that calibration failed, you need to calibrate manually. The cursor location and pen position should match after calibration. If not, you may need to calibrate manually.
Parent topic: Pen Calibration Related tasks Calibrating Manually Focusing the Image Calibrating Manually If the cursor location and pen position do not match after auto calibration, you can calibrate manually. 1. Press the Menu button, select the Extended menu, and press Enter. 2. Select the Easy Interactive Function setting and press Enter.
3. Select Manual Calibration and press Enter. 4. Adjust the image focus, if necessary. 5. Press Enter to select Yes. A flashing green circle appears in the upper left corner of your projected image. 6. Touch the center of the circle with the tip of the pen. The circle disappears, and you see another circle below the first one.
Note: For the most accurate calibration, make sure you touch the center of the circle. Note: Make sure you are not blocking the signal between the pen and the interactive receiver (next to the projection window on the projector). 7. Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next circle appears at the top of a new column. Note: If you make a mistake, press the Esc button on the remote control to go back to the previous circle.
Related tasks Focusing the Image Calibrating Automatically Using Finger Touch Interactivity You can use your finger to perform the same functions as the interactive pens when you install the Touch Unit (BrightLink 695Wi). Note: See the Touch Unit and Control Pad Installation Guide for detailed instructions on installing the Touch Unit and calibrating for finger touch interactivity (BrightLink 695Wi).
Follow these precautions when using the Touch Unit and finger touch interactivity: • Children using finger touch interactivity should always be accompanied by an adult. • Never disassemble or modify the Touch Unit. Never open any cases on the projector or Touch Unit. Electrical voltages inside the projector can cause severe injury. • Do not look into the laser diffusion ports on the back of the Touch Unit. The laser can damage your eyes. Extra care should be taken when children are present.
Parent topic: Using Finger Touch Interactivity Calibrating for Finger Touch Interactivity Finger touch calibration coordinates the positioning of your finger with the location of the cursor (BrightLink 695Wi). Note: Make sure you have calibrated the pens before calibrating for finger touch interactivity. 1. Press the Menu button, select the Extended menu, and press Enter. 2. Select the Easy Interactive Function setting and press Enter.
3. Select Touch Unit Setup and press Enter. 4. Select Touch Calibration and press Enter. The following screen appears: 5. Adjust the image focus, if necessary. 6. Press Enter to select Yes. A flashing green circle appears in the upper left corner of your projected image.
7. Touch and hold the center of the circle with your finger until the circle disappears and another circle appears, then release it. The circle disappears, and you see another circle below the first one. Note: For the most accurate calibration, make sure you touch the center of the circle with the tip of your finger. Note: Make sure you are not blocking the signal between your finger and the interactive receiver (next to the projection window on the projector). 8.
When you get to the bottom of a column, the next circle appears at the top of a new column. Note: If you make a mistake, press the Esc button on the remote control to go back to the previous circle. To restart the calibration process, press and hold the Esc button for 2 seconds. 9. If the cursor location and your finger position do not match, repeat these steps to calibrate again.
3. Adjust the angle of the Touch Unit as described in the Touch Unit and Control Pad Installation Guide. 4. Calibrate for finger touch interactivity. 5. Turn on your projector. This automatically turns on the Touch Unit also. The blue light on the Touch Unit remains lit. 6. To write or draw on the projection surface in built-in annotation mode or built-in whiteboard mode, do the following: • To select a projected item, such as an icon, tap the projection surface with your finger.
• To scroll, drag your finger on the screen. 8. If your operating system supports these functions, you can also do the following: • To zoom in or out, touch an item using two fingers and either move your fingers away from each other (zoom in) or toward each other (zoom out). • To rotate an image, touch the image with your fingers and rotate your hand. • To drag up or down on a page, or move backward or forward in a browser window, use swiping gestures or flicks.
• Use the Easy Interactive Tools software to annotate with both pens or a combination of pen and finger touch (BrightLink 695Wi) at the same time Note: See the online Easy Interactive Tools Operation Guide for detailed information. • Save and print your annotations • Use the Tablet PC input panel in Windows 10, 8.
3. Select the Easy Interactive Function setting and press Enter. 4. Select Advanced in the PC Interactive section and press Enter. 5. Select Manual Adj. Pen Area and press Enter.
You see this screen: 6. Press Enter to select Yes. The mouse pointer moves toward the top left corner. 7. When the mouse pointer stops at the top left corner of the image, touch the tip of the pointer with the interactive pen. The mouse pointer moves toward the bottom right corner. 8. When the mouse pointer stops at the bottom right corner of the image, touch the tip of the pointer with the interactive pen.
Parent topic: Using BrightLink with a Computer Windows Pen Input and Ink Tools If you are using Windows 10, 8.x, Windows 7, or Windows Vista, you can use the pen input and Ink tools to add input and annotations to your work. You can also use these features over a network when you set the interactive features to be available on your network. See the EasyMP Multi PC Projection Operation Guide for instructions on setting up your computer for network projection.
2. Select the Easy Interactive Function setting and press Enter. 3. Select Pen Operation Mode and press Enter. 4. Select Windows/Mac Mode and press Enter. Parent topic: Windows Pen Input and Ink Tools Using Windows Pen Input and Ink Tools If you are using Windows 10, Windows 8.x, Windows 7, or Windows Vista, you can add handwritten input to your work and convert it to text.
• To open the Tablet PC input panel in Windows 7 or Windows Vista, select Accessories > Tablet PC > Tablet PC Input Panel. > All Programs > You can write in the box using the interactive pen or your finger(BrightLink 695Wi), and select from a variety of options to edit and convert the text. • To add Ink annotations in Microsoft Office applications, select the Review menu, and select Start Inking. Note: In Microsoft Word or Excel, select the Insert tab and select Start Inking.
These two modes are available: • Built-in annotation mode displays the built-in toolbar on whatever image is being projected from a document camera, iPad, or other source. • Built-in whiteboard mode lets you project a white or black screen or one of 4 background patterns, and use the toolbar to write or draw as you would on a chalkboard or dry erase board.
Note: If you want to hide the toolbar automatically after drawing, select the toolbar. icon at the bottom of the Parent topic: Using BrightLink Without a Computer Built-in Tools for Use Without a Computer The built-in toolbar is embedded in the projector and allows you to draw and write on the projected screen.
Switch to built-in annotation mode Switch to built-in whiteboard mode Undo the last annotation Redo the last undo Switch to the computer interactive mode Select a white or black background or one of 4 patterns (whiteboard mode only) Change custom pen or highlighter color and width Write or draw free-form lines with custom pen Write or draw free-form lines with transparent highlighter pen 180
Black pen (fine point on left, thick on right) Red pen (fine point on left, thick on right) Blue pen (fine point on left, thick on right) Eraser (thin width on left, thick on right) Clear all annotations Hide the toolbar after each annotation Close the toolbar Parent topic: Using BrightLink Without a Computer Using the Built-in Whiteboard Mode In built-in whiteboard mode, you can project a solid or patterned background, and then write or draw on it as you would on a chalkboard or dry erase board. 1.
2. If you want to change the background, do the following: • Select the Background tool. • Select a black background or one of 4 different patterns. • Select the right arrow icon to close the selection window. 3. Do one of the following to write or draw on the background. • To erase, select the Eraser tool. • To clear the whole screen, select the Clear all tool.
Display the Home screen. Print the projected image Save the projected image to a connected USB storage device Share the projected image using EasyMP Multi PC Projection or Epson iProjection Change the image source using a displayed list. (To close the image source list, select the arrow icon at the bottom of the list.
Project two images from different image sources Set the timer Display the document camera control toolbar. (Not all settings may be available depending on your document camera model.
Related tasks Turning On the Projector Controlling the Volume with the Volume Buttons Starting a PC Free Movie Presentation Resizing the Image with the Wide and Tele Buttons Selecting an Image Source Selecting a Networked Device Source You can project an image from up to 50 devices connected to the projector via a network. You can select the image source from computers running EasyMP Multi PC Projection or Epson iProjection, and smartphones or tablets running Epson iProjection. 1.
You see a list of available devices. The icon next to a user name indicates the currently selected source. 3. Select the user name for the device from which you want to project. Note: Select Refresh to update the user list. 4. Select Return. You see the screen image from the selected device.
Splitting the Screen You can split the screen and project from two sources at the same time. You can annotate and interact with both sources. 1. Select the Split tool on the bottom toolbar. You see a screen like this: 2. Select the two sources you want to display. (Not all combinations of sources are valid.) Note: If you want to write on a blank screen, select any unused source. Unused sources display the color selected in the Display Background setting. The Logo option will display a blue background. 3.
4. Do any of the following as necessary: • To change to a different source at any time, press the Menu button on the remote control and select Source, or press the Split icon on the bottom toolbar. • To use PC interactive mode on the right screen, press the Menu button on the remote control, select Target Pen Mode, and select Screen Right. Set the Pen Mode setting to PC Interactive. Note: If you select Video, USB1, or USB2 as a source, you cannot use PC interactive mode.
Selecting Interactive Split Screen Settings You can select split screen projection settings using the projector control toolbar. 1. Select the Split tool on the bottom toolbar. 2. Select the tab. You see a screen like this: 3. Do any of the following as necessary: • To make one image larger than the other, select a Screen Size setting. • To use the interactive pen as a mouse with a computer source, select a Target Pen Mode setting.
Interactive Features when Projecting with Two Projectors You can use your projector's interactive features while projecting with two projectors installed side by side. To get started, install the software from the Easy Interactive Function CD. See the installation guide that came with your projector mount for detailed instructions on installing multiple projectors and making the necessary settings for the interactive features. Note: You may not be able to write and draw across the border of the images.
2. Press the icon. You see a screen like this: 3. Set the Use this single projector to On. You can now use the interactive features on the current projector only.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Color Temp. (color temperature) Color Temp. Customized Description Color Temp.: Sets the overall color tone. Lower values tint the image red, and higher values tint the image blue. Customized: Adjusts the intensity of individual hues in the image Image Enhancement Noise Reduction Reduces flickering in analog images Advanced Gamma Gamma: adjusts the coloring by selecting one of the gamma correction values, referring to the projected image, or a gamma graph.
Parent topic: Adjusting the Menu Settings Related references Available Image Aspect Ratios Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
Setting Options Description Aspect See the list of available aspect ratios Sets the aspect ratio (width-toheight ratio) for the selected input source Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Tracking Varying levels available Adjusts signal to eliminate vertical stripes in computer images Sync.
Setting Options Description Advanced HDMI Video Range HDMI Video Range: Sets the video range to match the setting of the device connected to the HDMI input port Input Signal Video Signal • Auto: detects the video range automatically • Normal: normally for images from a device other than a computer; can also be selected if the black areas of the image are too bright • Expanded: normally for images from a computer; can also be selected if the image is too dark Input Signal: Specifies the signal type fr
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description Split Screen — Divides the viewing area horizontally and displays two images side-by-side; while in Split Screen mode, press Menu to display the Split Screen options or Esc to cancel split screen display Zoom Varying levels available Adjusts the size of the projected image Image Shift Varying positions available Adjusts the position of the projected image Volume Varying levels available Adjusts the volume of projector’s speaker system or external speakers HDMI Link
Setting Options Description Lock Setting Control Panel Lock Controls projector button locking to secure the projector Full Lock: locks all buttons Partial Lock: locks all buttons except the power button Off: no buttons locked Pointer Shape Three shapes available Changes the shape of the remote control pointer feature Mic Input Level Varying levels available Adjusts the volume of the projector's speaker system when you use a connected microphone Remote Receiver Front/Rear Limits reception of re
Setting Options Description Pattern Pattern Display Selects various pattern display options Pattern Type User Pattern Test Pattern Pattern Display: lets you display the selected pattern type on the screen to aid in presentation Pattern Type: selects the type of grid or line pattern to display User Pattern: captures a projected screen and saves it as a pattern for display Test Pattern: displays a test pattern to assist in focusing and zooming the image and correcting image shape Installation Guide —
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation.
Setting Options Description Touch Unit Setup Installation Pattern Select settings for the Touch Unit (BrightLink 695Wi) Power Installation Pattern: displays reference points to help you determine the installation position of the Touch Unit Angle Adjustment Touch Calibration Power: turns on the Touch Unit power Angle Adjustment: performs angle adjustment for laser diffusion Touch Calibration: performs calibration for finger touch operations Pen Mode PC Free Annotation PC Interactive Selects the m
Setting Options Description Advanced Distance of Projectors Selects various settings for interactive features Sync of Projectors Multi-Projection Wired Sync Mode Preset Pen Thickness Eraser Size Color Palette Pen Button Function Default Touch Action Confirm Clear Screen Distance of Projectors, Sync of Projectors, Multi-Projection, and Wired Sync Mode: let you adjust features for using multiple projectors of the same model in the same room Preset Pen Thickness: lets you select the default pen thicknes
Setting Options Description Enable Right Click On Lets you use a long pen press or finger press (BrightLink 695Wi) as a right-click operation when using mouse mode Off Advanced Pen Tip Button Auto Adjust Pen Area Manual Adj. Pen Area Select pen operation and adjustment options Pen Tip Button: assign either Right Click or Left Click to the pen tip button Select either Auto Adjust Pen Area or Manual Adj.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen A/V Mute Color Uniformity Toolbars Pen Mode Icon Projector Control Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Co
Setting Options Description User's Logo —– Creates a screen that the projector displays to identify itself and enhance security Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Upside Down Rear Rear Upside Down 208
Setting Options Description Operation Direct Power On Selects various operation options High Altitude Mode Direct Power On: lets you turn on the projector without pressing the power button Auto Source Search Auto Power On Monitor Out Port Connect ELPCB02 Date & Time High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) Auto Source Search: automatically detects the image signal that is input when the projector is turned on Auto Power On: automatica
Setting Options Description A/V Settings A/V Output Selects the following when the projector is in standby mode (turned off): Audio Output HDMI1 Audio Output HDMI2 Audio Output HDMI3 Audio Output A/V Output: the Always On setting indicates that the projector output audio and video signals even while it is standby mode; only available when Standby Mode is set to Communication On Audio Output: selects the audio input port when projecting images from the Computer1, Computer2, Video, and USB-A ports HDMI
Setting Options Description USB Type B Easy Interactive Function Selects what happens when you connect your computer to the projector's USB-B port USB Display/Easy Interactive Function Wireless Mouse/USB Display Easy Interactive Function: lets you use the interactive pens or your finger (BrightLink 695Wi) with your computer USB Display/Easy Interactive Function: lets you display your computer's image through the USB port and use the interactive pens or your finger (BrightLink 695Wi) with your compute
Setting Options Description Multi-Projection Multi-Projection Selects the following when you use multiple projectors: Projector ID Color Mode Color Uniformity Brightness Level Color Matching RGBCMY Reset Multi-Projection: matches the display settings of multiple projectors Projector ID: assigns an ID for the projector when you use multiple projectors Color Mode: adjusts the vividness of image colors for various image types and environments Color Uniformity: adjusts the color tone balance Brightness L
Calibrating for Finger Touch Interactivity Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Wireless LAN Sys. Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Net.
Wireless Network Projection Projector Setup Settings - ECO Menu Settings on the ECO menu let you customize projector functions to save power. When you select a power-saving setting, a leaf icon appears next to the menu item.
Setting Options Description Light Optimizer On When Power Consumption is set to Normal, the lamp brightness is adjusted based on the projected image; you can set this option for each color mode Off Sleep Mode On Automatically places the projector in standby mode after an interval of inactivity Off Sleep Mode Timer 1 to 30 minutes Sets the interval for Sleep Mode A/V Mute Timer On Automatically turns off the projector after 30 minutes if A/V Mute is enabled Off Standby Mode Communication On
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Select Version to display the projector's firmware version. Select Projector Info to display the settings described below. Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Information item Description Refresh Rate Displays the refresh rate of the current input source Sync Info Displays information that may be needed by a service technician Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Event ID Displays the Event ID number corresponding to a specific projector problem; see the list of Event ID codes Event ID Code List Parent topic: Adjusting the Menu Settings Rela
Event ID code Cause and solution 0479 A projector system error has occurred. Turn the projector off and then on again. 04FF 0891 Cannot find the SSID (network name). Make sure your computer and projector are connected to your access point's current SSID. 0892 The WPA/WPA2 authentication type does not match. Make sure the wireless network security settings are correct. 0893 The TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct.
You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the projection window and obstacle sensor periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the projection window. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use canned air, or the gases may leave a flammable residue.
Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector. Caution: Do not use wax, alcohol, benzine, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a residue.
2. Slide the air filter cover latch and open the air filter cover.
3. Pull the air filter out of the projector. 4. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.
5. Place the air filter back in the projector as shown.
6. Close the air filter cover and slide the latch.
You can replace the air filter while the projector is mounted on the wall or ceiling. 1. Turn off the projector and unplug the power cord. 2. Slide the air filter cover latch and open the air filter cover.
3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations. 4. Place the new air filter in the projector as shown.
5. Close the air filter cover and slide the latch. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replace the lamp as soon as possible when the following occurs: • The projected image gets darker or starts to deteriorate • A message appears when you turn on the projector telling you to replace the lamp • The projector's Lamp light is flashing orange and its power light is flashing blue Replacing the Lamp Resetting the Lamp Timer Parent topic: Projector Maintenance Related references Optional Equipment and Replacement Parts Projector Lamp Specifications Projector Information Display - Info Menu Replacing
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. 4. Slide off the lamp cover.
5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector along the guide rail. If it does not fit easily, make sure it is facing the right way. Press the handle down. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Tighten the screws to secure the lamp.
9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Replacing the Soft Pen Tips If the pen tips become damaged or no longer work correctly, you can replace them.
1. Twist off the tip of the pen to remove it. 2. Remove the soft tip.
3. Insert the new tip. 4. Twist on the pen tip.
Replacing the Hard Pen Tips If the pen tips become damaged or no longer work correctly, you can replace them. 1. Twist off the tip of the pen to remove it.
2. Twist on the new tip. Parent topic: Projector Maintenance Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Remove any equipment connected to the projector. • When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solving Interactive Problems Solving Network Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here. 1 Power light 2 Status light 3 Lamp light 4 Temp (temperature) light Power light Status light Lamp light Temp light Status and solution Blue Blue Off Off Normal operation. Blue Flashing blue Off Off Warming up. Wait for an image to appear.
Power light Status light Lamp light Temp light Status and solution Blue Off Off Off Standby or sleep mode. Blue Flashing blue Off Off Shutting down. (When the Status light stops flashing, you can unplug the projector.) Blue Varies Off Flashing orange Projector is too hot. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter. • Make sure the environmental temperature is not too hot.
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem. Off • Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. • Clean or replace the air filter. • If operating the projector at high altitude, turn on High Altitude Mode. • If the problem persists, unplug the projector and contact Epson for help.
Where to Get Help Related tasks Cleaning the Air Filter and Vents Replacing the Air Filter Replacing the Lamp Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Home button on the projector or the remote control. 3. Press the arrow buttons to select Help. 4. Press Enter. You see the Help menu. 5. Press the up and down arrow buttons to highlight the problem you want to solve. 6.
Solutions to Sound Problems Solutions to Microphone Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Press the A/V Mute button on the remote control to see if the image was temporarily turned off. • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Related tasks Unlocking the Projector's Buttons Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the USB button on the remote control. • Make sure the USB Display software has installed correctly. Install it manually if necessary.
• If necessary, turn the projector and the connected computer or video source off and then on again. • If the other solutions do not solve the problem, reset all of the projector settings using the options on the Reset menu. Displaying From a PC Laptop Displaying From a Mac Laptop Parent topic: Solving Image or Sound Problems Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1.
• As a test, try setting the computer's display resolution to the lowest possible setting, and then gradually increase it as necessary. Parent topic: Solving Image or Sound Problems Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal.
Note: Adjusting Quick Corner and H/V-Keystone settings may affect focus and pen calibration.
Related references Input Signal Settings - Signal Menu Supported Video Display Formats Related tasks Displaying From a PC Laptop Displaying From a Mac Laptop Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projection window. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it.
• Make sure you selected the correct Input Signal or Video Signal setting on the Signal menu, if available for your image source. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables. • If you are using the ECO or ECO2 Power Consumption setting, try selecting Normal in the projector's menus. • Position the projector close enough to the screen.
• If you want to use a connected audio source when the projector is off, set the Standby Mode option to Communication On and the A/V Output option to Always On. • Make sure the Audio Output option is set to the correct audio port for your video device. • If you turn the projector on immediately after turning it off, the cooling fans may run at high speed momentarily and cause an unexpected noise. This is normal.
• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector. • If the projector's lamp shuts off unexpectedly, it may have entered standby mode after a period of inactivity. Press the power button to wake the projector and adjust the Sleep Mode Timer setting to change the sleep interval. • If the projector's lamp shuts off and the power and Temp lights are red, the projector has overheated and shut off.
Parent topic: Solving Projector or Remote Control Operation Problems Related references Projector Feature Settings - Settings Menu Optional Equipment and Replacement Parts Remote Control Operation Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control.
Parent topic: Solving Problems Solutions When "Error Occurred in the Easy Interactive Function" Message Appears If the "Error occurred in the Easy Interactive Function" message appears, contact Epson for help. Parent topic: Solving Interactive Problems Related references Where to Get Help Solutions When the Interactive Pens Do Not Work If the interactive pens do not work, try the following solutions: • The pens turn off automatically when not in use. Pick up the pen to turn it back on.
• Make sure the Pen Mode and Pen Operation Mode settings are set correctly in the Easy Interactive Function options on the Extended menu. • If you are using multiple projectors in the same room, change the Distance of Projectors setting in Easy Interactive Function on the Extended menu.
• For the best performance, connect your computer to the projector using a VGA or HDMI cable for display and the USB cable for interactivity. • If you are using USB Display in Windows, you may need to disable Windows Aero in the Epson USB Display Settings program on your computer. • If you are having difficulty double-clicking on a Mac, go to the System Preferences menu, select Mouse, Trackpad, or Mouse & Trackpad, and reduce the Double-click speed.
• If touch operation does not work correctly even after calibration, press the icon on the Home screen and check the Calibration Range setting. Select Wide if you drag items when touching the screen, or Narrow if mouse operations do not work smoothly. Parent topic: Solving Interactive Problems Solving Network Problems Check the solutions in these sections if you have problems using the projector on a network.
Note: You cannot change the user ID. • To display the Web Control screen, enter EPSONWEB as the user ID, and enter the password set in the projector's Network menu as the password. The default password is admin. • To display the Web Remote screen, enter EPSONREMOTE as the user ID and enter the password set in the projector's Network menu as the password. The default password is guest. • Make sure you have access to the network the projector is on. Note: The user ID and password are case sensitive.
• Description of the problem Purchase Supplies and Accessories You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales). To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).
Technical Specifications These sections list the technical specifications of your projector.
Image size 60 inches (1.52 m) to 99 inches (2.51 m) (in native aspect ratio) Projection distance 13.9 inches (35.4 cm) to 23.7 inches (60.1 cm) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:10 (width-to-height) Focus adjustment Manual Zoom adjustment Digital Zoom ratio 1:1.
Lamp life Normal Power Consumption mode: up to about 5000 hours ECO Power Consumption mode: up to about 10000 hours ECO2 Power Consumption mode: up to about 9000 hours Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications Reception range 19.
Power consumption Operating: (100 to 120 V) Normal Power Consumption mode: 373 W ECO Power Consumption mode: 324 W ECO2 Power Consumption mode: 324 W Standby: 0.23 W (Energy Saving), 2.2 W (Networked Standby) Power consumption Operating: (220 to 240 V) Normal Power Consumption mode: 354 W ECO Power Consumption mode: 309 W ECO2 Power Consumption mode: 309 W Standby: 0.37 W (Energy Saving), 2.
Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B UL60950-1 Canada ICES-003 Class B CSA C22.2 No. 60950-1 Parent topic: Technical Specifications Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 70/75/85 1152 × 864 60/75/85 1280 × 1024 60/75/85 1280 × 960 SXGA+ 60/75 1400 × 1050 WSXGA+ 60 1680 × 1050 UXGA 60 1600 × 1200 TV (NTSC) 60 720 × 480 TV (SECAM) 50 720 × 576 TV (PAL) 50/60 720 × 576 SDTV (480i) 60 720 × 480 SDTV (576i) 50 720 × 576 SDTV (480p) 60 720 × 480 SDTV (576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XG
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 VGA 60 640 × 480 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 MHL in
Requirement Windows Mac Operating system Windows Vista Ultimate, Enterprise, Business, Home Premium, and Home Basic (32-bit) Mac OS X 10.5.x (32-bit), and 10.6.x, 10.7.x , 10.8.x, 10.9.x, 10.10.x, and 10.11.x (32- and 64bit); macOS 10.12.x (32- and 64-bit) Windows 7 Ultimate, Enterprise, Professional, and Home Premium (32and 64-bit); Home Basic and Starter (32bit) Windows 8.x, Pro, and Enterprise (32and 64-bit) Windows 10 Home, Pro, and Enterprise (32- and 64-bit) USB version USB 2.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Open Source Software License Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place your hand or any object near the projection window. The high temperature of this area could cause burns, fire, or other damage. • Do not place the projector on an unstable cart, stand, or table.
setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and the projector. • Do not operate the projector in a closed-in cabinet unless proper ventilation is provided. • Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.
41 to 104 °F (5 to 40 °C) at an altitude of 7500 feet (2286 m) or less, or 41 to 95 °F (5 to 35 °C) at a higher altitude When using multiple projectors at the same time: Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature. • Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time.
WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.
No. 4 Symbol Approved Standards Description ISO7000 Caution No.0434B, To identify general caution when using the product. IEC3864-B3.1 5 6 IEC60417 Caution, hot surface No.5041 To indicate that the marked item can be hot and should not be touched without taking care. IEC60417 Caution, risk of electric shock No.6042 To identify equipment that has risk of electric shock. ISO3864-B3.6 7 8 9 IEC60417 For indoor use only No.
No. 11 12 Symbol Approved Standards Description IEC60417 Positioning of cell No.5002 To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. — Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. 13 14 15 16 17 IEC60417 Protective earth No.
No. Symbol 18 Approved Standards Description ISO 3864 General prohibition To identify actions or operations that are prohibited. 19 ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. 20 — Never look into the optical lens while the projector is on. 21 — To indicate that the marked item don’t place anything on projector. 22 ISO3864 Caution, laser radiation IEC60825-1 To indicate the equipment has a laser radiation part.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
If you desire to receive the source code of the GPL Programs, contact Epson. These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs The list of GPL Programs • busybox-1.21.0 • iptables-1.4.20 • linux-3.4.49 • patches • udhcp 0.9.8 • wireless_tools 29 • dbus-1.6.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail.
LGPL Programs • SDL-1.2.15 • SDL-Image • alsa-lib-1.0.27.2 • libdbus-c++-0.9.0 • grencode-3.4.2 • libnl-3.2.24 • glibc-2.17 The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in nonfree programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13.
How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library.
List of libjpeg programs • libjpeg-6b License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows. Copyright (C) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software. For conditions of distribution and use, see the accompanying README file. This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us. Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as "the Independent JPEG Group's software".
List of libpng programs • libpng-1.2.49 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows. This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail. COPYRIGHT NOTICE, DISCLAIMER, and LICENSE: If you modify libpng you may insert additional notices immediately following this sentence.
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg (88x31) and "pngnow.png" (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp at users.sourceforge.
jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code. If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib". The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of newlib programs • newlib 1.17.0 License terms of conditions of each program which are provided by owner of the copyright to the "newlib" are as follows.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
(4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc. This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD. AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
Copyright 2002 SuperH, Inc. All rights reserved This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH. SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (14) Alexey Zelkin Copyright (c) 2000, 2001 Alexey Zelkin All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. (18) Citrus Project Copyright (c)1999 Citrus Project, All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Copyright (c) 2001 Mike Barcroft All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. iconv (Charset Conversion Library) v2.0 (28) Artem Bityuckiy (--enable-newlib-iconv) Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic Publishers. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (37) MIPS Technologies, Inc /* * Copyright (c) 2009 MIPS Technologies, Inc. * All rights reserved.
List of MIT License programs • jquery-1.7.2.min.js • jquery-ui-1.8.20 • jquery.ui.touch-punch.js • jquery.upload-1.0.2.min.js • jquery-1.11.3.min.js • jquery-ui-1.11.4 License terms of conditions of each program which are provided by owner of the copyright to the "MIT License" are as follows. Copyright (c) 2012 jQuery Foundation and other contributors, http://jquery.
License terms of conditions of each program which are provided by owner of the copyright to the "TOPPERS/JSP" are as follows. TOPPERS/JSP Kernel Toyohashi Open Platform for Embedded Real-Time Systems/Just Standard Profile Kernel Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of Technology, JAPAN Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory Graduate School of Information Science, Nagoya Univ., JAPAN.
TINET This projector product includes the open source software program "TINET" which applies the terms and conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of TINET programs • tinet-1.4.4 License terms of conditions of each program which are provided by owner of the copyright to the "TINET" are as follows.
(6) TINET and TOPPERS TINET (TCP/IP Protocol Stack) Copyright (C) 2001-2006 by Dep.
License terms of conditions of each program which are provided by owner of the copyright to the "WPA Supplicant" are as follows. Copyright (c) 2003-2014, Jouni Malinen and contributors All Rights Reserved. This program is licensed under the BSD license (the one with advertisement clause removed). If you are submitting changes to the project, please see CONTRIBUTIONS file for more instructions.
List of lighttpd programs • lighttpd-1.4.35 License terms of conditions of each program which are provided by owner of the copyright to the "lighttpd" are as follows. Copyright (c) 2004, Jan Kneschke, incremental All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
PCRE LICENCE ----------PCRE is a library of functions to support regular expressions whose syntax and semantics are as close as possible to those of the Perl 5 language. Release 8 of PCRE is distributed under the terms of the "BSD" licence, as specified below. The documentation for PCRE, supplied in the "doc" directory, is distributed under the same terms as the software itself. The basic library functions are written in C and are freestanding.
Emain domain: freemail.hu Copyright(c) 2009-2012 Zoltan Herczeg All rights reserved. THE C++ WRAPPER FUNCTIONS ----------Contributed by: Google Inc. Copyright (c) 2007-2012, Google Inc. All rights reserved. THE "BSD" LICENCE ----------Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
FastCGI This projector product includes the open source software program "FastCGI" which applies the terms and conditions provided by owner of the copyright to the "FastCGI" The "FastCGI" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of FastCGI programs • fcgi-2.4.0 License terms of conditions of each program which are provided by owner of the copyright to the "FastCGI" are as follows.
Binding Arbitration and Class Waiver 1. DISPUTES, BINDING INDIVIDUAL ARBITRATION, AND WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS 1.1 Disputes. The terms of this Section 1 shall apply to all Disputes between you and Epson.
1.5 WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS. YOU AND EPSON AGREE THAT EACH PARTY MAY BRING DISPUTES AGAINST THE OTHER PARTY ONLY IN AN INDIVIDUAL CAPACITY, AND NOT AS A PLAINTIFF OR CLASS MEMBER IN ANY CLASS OR REPRESENTATIVE PROCEEDING, INCLUDING WITHOUT LIMITATION FEDERAL OR STATE CLASS ACTIONS, OR CLASS ARBITRATIONS. CLASS ACTION LAWSUITS, CLASS-WIDE ARBITRATIONS, PRIVATE ATTORNEY-GENERAL ACTIONS, AND ANY OTHER PROCEEDING WHERE SOMEONE ACTS IN A REPRESENTATIVE CAPACITY ARE NOT ALLOWED.
(iii) Send one copy of the Demand for Arbitration to the other party (same address as the Dispute Notice), or as otherwise agreed by the parties. b) Hearing Format. During the arbitration, the amount of any settlement offer made shall not be disclosed to the arbitrator until after the arbitrator determines the amount, if any, to which you or Epson is entitled. The discovery or exchange of non-privileged information relevant to the Dispute may be allowed during the arbitration. c) Arbitration Fees.
1.9 Severability. If any provision in this Section 1 is found to be unenforceable, that provision shall be severed with the remainder of this Agreement remaining in full force and effect. The foregoing shall not apply to the prohibition against class or representative actions as provided in Section 1.5. This means that if Section 1.5 is found to be unenforceable, the entire Section 1 (but only Section 1) shall be null and void.
product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. This information is subject to change without notice.
