SERVICE MANUAL Color Inkjet Printer EPSON Stylus NX100/NX105/SX100/ SX105/TX100/TX101/TX102/ TX103/TX105/TX106/TX109/ ME 300 Confidential SEMF08-002
Notice: All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The contents of this manual are subject to change without notice. All effort have been made to ensure the accuracy of the contents of this manual.
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings. WARNING Signals a precaution which, if ignored, could result in damage to equipment.
About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Manual Configuration This manual consists of six chapters and Appendix. CHAPTER 1.PRODUCT DESCRIPTIONS Provides a general overview and specifications of the product. CHAPTER 2.
Revision Status Revision Date of Issue A June 27, 2008 Description First Release Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Contents Chapter 1 PRODUCT DESCRIPTION Chapter 2 OPERATING PRINCIPLES 1.1 Features................................................................................................................. 9 1.2 Printing Specifications........................................................................................ 10 1.2.1 Basic Specifications....................................................................
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Chapter 4 DISASSEMBLY/ASSEMBLY 4.1 Overview ............................................................................................................ 4.1.1 Precautions .............................................................................................. 4.1.2 Tools ........................................................................................................ 4.1.3 Work Completion Check ..............
CHAPTER 1 PRODUCT DESCRIPTION Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 1.1 Features Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/ TX105/TX106/TX109/ME 300 are entry class color ink-jet printers with the scanner function. Features Maximum print resolution: 5760 (H) x 1440 (V) dpi D2 Chips printhead (Black: 90 nozzles x 1, Color: 29 nozzles x 3 per color) Borderless printing with pigment ink Four independent ink cartridges is installed.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.2 Printing Specifications Revision A 1.2.2 Ink Cartridge The product numbers of the EPSON ink cartridges for this printer are shown below. 1.2.1 Basic Specifications Table 1-2. Product No. of Ink Cartridges Table 1-1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.2.3 Print Mode Table 1-5. Print Mode (Monochrome) Media Table 1-4.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 1.2.4 Supported Paper The table below lists the paper type and sizes supported by the printer. The supported paper type and sizes vary depending on destinations (between EAI, EUR, and Asia). Table 1-6. Supported Paper Paper Name Paper Size Thickness (mm) Weight EAI EUR Asia P*1 B*2 P*1 B*2 P*1 B*2 Legal 215.9 x 355.6 mm (8.5”x14”) Y - Y - Y - Letter 215.9 x 279.4 mm (8.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 1-6.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.2.5 Printing Area 1.3 Scanner Specifications The printing area for this printer is shown below. Table 1-8. Basic Specifications Table 1-7.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.4 General Specifications 1.4.2 Environmental Conditions Table 1-11. Environmental Conditions 1.4.1 Electrical Specifications Table 1-10. Primary Power Specifications Item 100-120 V model 220-240 V model Rated power supply voltage 100 to 120 VAC 220 to 240 VAC Input voltage range 90 to 132 VAC 198 to 264 VAC Rated current (Max. rated current) 0.6 A (TBD A) 0.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.5 Interface 1.4.3 Durability Total print life: 10,000 pages (A4, 3.5% duty), or three years which ever comes first Printhead: Five billions shots (per nozzle) or five years which ever comes first Scanner carriage: 36,000 cycles of carriage movement 1.4.4 Acoustic Noise T.B.D.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 1.6 Control Panel 1.6.1 Operation Buttons & LEDs The following buttons and LEDs are equipped on the control panel. Table 1-15. Buttons & LEDs Button/LED Power Stop Button Start Photo Start B&W Start Color Power LED LED Paper LED Ink LED Function Turns the power ON/OFF. Stops printing immediately and ejects the paper. Cancels the job which is printing/copying at the same time.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 1.6.2 Control Panel Functions Table 1-16. Buttons Functions Button Power Printer Status Functions Power Off Turns the power OFF. Power On Turns the power ON. Ejects the paper if the paper is not ejected yet. Stop Printing / Copying Stops printing immediately and ejects the paper. Cancels the job which is printing/copying at the same time.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 1-16. Buttons Functions Button Printer Status Color*3 Functions Start (when pressed for 3 seconds or more) Ready / Ink Low Adjust the size to the paper and starts color copying. Sleep Recovers from sleep, adjust the size to the paper and starts color copying. Stop + Start B&W Ready / Ink Low Starts B&W copying in the draft mode.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 1-17.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 1.7 Stand-alone Copy Function 1.7.2.1 Relation Between Original and Copy The scanning start position is located on the front right of the scan bed. The relations between the original placed face down and its copy are as follows. 1.7.1 Supported Paper and Copy Mode Table 1-18.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 1.7.3 Copy Speed Table 1-20. Copy Speed Copy Conditions (eMemo, A4 size, per copy) Monochrome copy 360 x 120 dpi Color copy Plain paper Monochrome copy 360 x 360 dpi Color copy Time 5 sec 14 sec 20 sec 72 sec 1.7.4 Multiple Copying Making 20 (fixed value) copies in color/B&W becomes available by operating specific keys (Refer to p. 18).
CHAPTER 2 OPERATING PRINCIPLES Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 2.1 Overview PF Encoder Sensor PF Scale This chapter describes the mechanism of Epson STYLUS NX100/NX105/SX100/ SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300. 2.1.1 Printer Mechanism Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/ TX105/TX106/TX109/ME 300 printer mechanism consists of printhead, carriage mechanism, paper loading mechanism, paper feed mechanism, and ink system.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 2.1.2 Motors & Sensors PF Motor Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/ TX105/TX106/TX109/ME 300 printer mechanism is equipped with the following printhead, motors and sensors. PE Sensor CR Encoder Sensor Table 2-1. Printer Mechanism Motors & Sensors No. 1 2 Name Printhead Refer to“ 2.1.3 Printhead ” (p.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 2.1.3 Printhead The D2 Chips type printhead is employed. Nozzle configuration Black: 90 nozzles x 1 Color: 29 nozzles x 3 (cyan, magenta, yellow) The nozzle layout as seen from behind the printhead is shown below. C#29 K#90 K#89 Paper feed direction C#1 M#29 M#1 Y#29 Y#3 Y#2 K#3 Y#1 K#2 K#1 Carriage movement direction Figure 2-4.
CHAPTER 3 TROUBLESHOOTING Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 3.1 Overview 3.1.2 Preliminary Checks This chapter describes how to solve problems. Before starting troubleshooting, be sure to verify that the following conditions are all met: W A R N IN G C H E C K P O IN T Be careful to avoid electric shocks when checking the electrical circuit boards (MAIN and PSE/PSB boards) while the power is turned on.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 3.2 Error Indications and Fault Occurrence Causes This chapter describes how the printer indicates an error status with LEDs, and why the error is caused, when a problem happened during each sequence/operation (power-on sequence, paper feeding, ink drawing, and so on). Table 3-1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 3.2.1 Troubleshooting by Error Message The following tables provide troubleshooting procedures. Confirm the error message indicated on the LED or the STM3 screen on the PC’s display, and verify it in the following list and the figures at the end of this chapter for the corresponding troubleshooting remedy.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position • Operation • Anywhere Detailed phenomenon The Scanner Carriage Unit. does not operate. Defective unit/part name Check point Remedy 1. Check if the grease is enough on the Guide Rail of the Lower Scanner Housing. (TBD) 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point 1. Check if the PF Motor Cable is connected to J6 on the Main Board. Remedy 1. Connect the PF Motor Cable to J6 on the Main Board.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the Upper Paper Guide is correctly assembled. 1. Reassemble the Upper Paper Guide to the Main Frame correctly. Upper Paper Guide The Carriage Unit collides with the Upper Paper Guide Unit when power is turned Upper Paper Guide on.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the Encoder FFC is connected to the CR Encoder Board. CR Encoder Board 1. Connect the Encoder FFC to the CR Encoder Board.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the Cap Assy and the Lever Cleaner are assembled correctly. 1. Reassemble the Cap Assy and Lever Cleaner correctly. Cap Assy • Power on • Anywhere When turning on the power, the Carriage cannot get out of home position.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-2. Check point for Fatal error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point 3. Check if the Spring Cleaner Lever comes off from the Lever Cleaner. Remedy 3. Reassemble the Cleaner Lever Spring correctly. Lever Cleaner • Power on • Anywhere When turning on the power, the Carriage cannot get out of home position.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A / Table 3-4. Check point for Paper jam error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the ASF Unit is properly installed. 1. Install the ASF Unit properly. 2. Check if the Paper Back Lever operates correctly in the paper loading sequence. 2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-4. Check point for Paper jam error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point 1. Check if the Extension Spring operates correctly in the paper loading sequence. Remedy 1. Set the Extension Spring between the Retard Roller Assy and the ASF Housing. Backside of ASF Unit Paper is being resent during paper feeding operation.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-4. Check point for Paper jam error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 2. Check if the Wheel Star Metal, Spring Star Wheel and Wheel Star Exit come off. 2. Reassemble the Wheel Star Metal, Spring Star Wheel and Wheel Star Exit correctly.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-5. Check point for Paper out error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point 1. Check if any paper dust is adhered to the surface of the LD Roller. LD Roller The LD Roller cannot pick up paper although the LD Roller attempt to rotate correctly. Remedy 1. Set a cleaning sheet in the ASF Unit up side down.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-5. Check point for Paper out error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the Extension Spring comes off from the Clutch 1. Reassemble the Extension Spring in the Clutch mechanism. mechanism. Extension Spring LD Roller Assy 2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-5. Check point for Paper out error according to each phenomenon Occurrence timing CR position • Operation •– Detailed phenomenon Defective unit/part name The LD Roller is not set to the ASF home position and paper is always loaded from the ASF Unit during the paper loading sequence. ASF Unit Check point 1. Check if the tip of the Change Lever is damaged. Remedy 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-7. Check point for Ink out error / No ink cartridge error read error / write error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if Ink Cartridge is properly installed. 1. Install the Ink Cartridge properly. 2. Check if the Memory Chip is disconnected or chipped. 2. Replace the Ink Cartridge with a new one.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-8. Check point for Communication error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name Panel Unit Check point Remedy 1. Check if the Panel FFC is damaged. 1. Replace the Panel Board with a new one. 2. Check if the Panel Board is damaged. 2. Replace the Panel Board with a new one. 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-8. Check point for Communication error according to each phenomenon Occurrence timing CR position Detailed phenomenon Defective unit/part name USB Cable Check point Remedy 1. Check if the USB Cable is connected between the printer 1. Connect the USB Cable to the printer and the and the PC. PC. 1. Check if an correct model name is stored into the address 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 3.2.2 Superficial Phenomenon-Based Troubleshooting This section explains the fault locations of the error states (print quality and abnormal noise) other than the error states (LED and STM3) in the previous section. Table 3-9.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-10. Check point for the abnormal noise Occurrence timing CR position • Anytime • Anywhere Defective unit/part name Detailed phenomenon The abnormal noise occurs at the first power on timing and during each operation although the printing operation is performed. Carriage Unit ASF Unit The bottom of the Carriage Unit contacts the surface of the EJ Frame Assy.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-12. Check point for the defective printing quality Print Quality State Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if there is not any foreign material/damage around 1. Remove the foreign material around the seal the seal rubber part on the Cap Assy. rubber parts carefully. Seal rubber part Ink is scarcely ejected to the Cap from the Printhead.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-12. Check point for the defective printing quality Print Quality State Detailed phenomenon Defective unit/part name Check point Remedy 1. Check if the Head FFC is securely connected to the Printhead Connectors and the Main Board Connectors. (J8, J9) 1. Connect the Head FFC to the Printhead and the Main Board Connectors.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-12. Check point for the defective printing quality Print Quality State Detailed phenomenon Defective unit/part name Printer driver & exclusive paper Check point 1. Check if the suitable paper is used according to the printer 1. Use the suitable paper according to the printer driver setting. driver setting. 1. Check if the Nozzle Check Pattern is printed correctly.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-12. Check point for the defective printing quality Print Quality State Detailed phenomenon Defective unit/part name Check point 1. Check if paper dust is adhered to the surface of the LD Roller. LD Roller • Print start position slip The printing operation is correctly performed. But, the top margin is insufficient than usual one. LD Roller 1. Check if the Lower Housing is free from ink stain.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 3-12. Check point for the defective printing quality Print Quality State Detailed phenomenon Defective unit/part name Printhead Check point 1. Check if the Printhead Cover has the ink drop. Upper Paper Guide 1. Check if the Upper Paper Guide Unit is free from ink stain. 2. Check if the Wheel Star Metal, Spring Star Wheel and Wheel Star Exit come off. • Ink stain of paper Remedy 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 3.2.3 Motor and Sensor Troubleshooting Motors The resistance values for the CR motor and the PF motor are given below, however, the values cannot be used to check the motors status since they are DC motor and the resistance between the electric poles varies. Visually check the motors for abnormal operation and if it is hard to judge, replace the motor. Table 3-13.
CHAPTER 4 DISASSEMBLY/ASSEMBLY Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.1 Overview C A U T IO N This section describes procedures for disassembling the main components of Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/ TX106/TX109/ME 300. Unless otherwise specified, disassembled units or components can be reassembled by reversing the disassembly procedure.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.1.3 Work Completion Check Table 4-2. Work Completion Check Classification If any service is made to the printer, use the checklist shown below to confirm all works are completed properly and the printer is ready to be returned to the user.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 4.2 Disassembly Procedures For disassembling each unit, refer to the pages in the following flowchart. Start “ 4.3.4 Scanner Stand / Cover Wire ” (p60) “ 4.3.1 Paper Support Tray ” (p58) “ 4.4.1 Panel Unit ” (p64) “ 4.3.5 Scanner Unit ” (p62) “ 4.3.3 Document Cover/ ASF Cover ” (p59) “ 4.3.2 Stacker Assy ” (p58) “ 4.3.6 Middle Housing ” (p63) “ 4.3.3 Document Cover/ ASF Cover ” (p59) “ 4.5.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.3 Removing the Housing 4.3.2 Stacker Assy Parts/Components need to be removed in advance: None 4.3.1 Paper Support Tray Removal procedure Parts/Components need to be removed in advance: None 1. 2. Removal procedure 1. 2. Revision A Open the Paper Support Tray. Release both the guide pins that secure the Paper Support Tray, and remove the Paper Support Tray. Open the Stacker Assy and pull it out.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 3. Bend the Stacker Assy to release the ribs, then separate the Tray Exit Outer and the Tray Exit Inner. Tray Exit Inner Rib Revision A 4.3.3 Document Cover/ASF Cover Parts/Components need to be removed in advance: None Removal procedure 1. Release both the guide pins with the hinge side held up slightly as shown below, and remove the ASF Cover from the Document Cover.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Install the Document Pad following the procedure below. 1. Place the Document Pad with the side where the double-sided tape attached upward on the Rod Lens Array aligning its corner with the home position. 2. Close the Document Cover to attach the Document Pad. 4.3.4 Scanner Stand /Cover Wire Parts/Components need to be removed in advance: None Removal procedure Scanner Stand 1. 2. Open the Scanner Unit.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Cover Wire 1. 2. Open the Scanner Unit. Release both the hooks in the direction of arrow, and remove the Cover Wire. Revision A Make sure not to catch the Scanner Motor Cable and the Scanner FFC with the Cover Wire. When installing the Cover Wire, insert the rib B so as to let the rib A of the Cover Wire under the Panel FFC. Scanner Unit Panel FFC Scanner FFC Scanner Motor Cable Cover Wire Hook Figure 4-9.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.3.5 Scanner Unit 2. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60) 3. Revision A Lift the left end of the Scanner Unit in the direction of arrow (1), then disengage the dowel from the cutout of the shaft hole in the Scanner Unit. Pull the Scanner Unit in the direction of arrow (2) and disengage the dowel from the shaft hole, then remove the Scanner Unit from the Middle Housing.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.3.6 Middle Housing 2. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire(p 60), Scanner Unit (p 62), Panel Unit (p 64) Revision A Release the two hooks on the left, two hooks on the right, and the hook on the rear (see Fig.4-14), then remove the Middle Housing from the Lower Housing. Left Side Removal procedure 1. Remove the six screws.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.4 Removing the Circuit Boards 3. Revision A Disconnect the Panel FFC from connector J2 on the Main Board, and remove the Panel Unit. 4.4.1 Panel Unit Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60) Panel FFC Removal procedure 1. Open the Scanner Unit. C A U T IO N 2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Buttons 4.4.2 Main Board 1. 2. Remove the Button Power and the Button OP from the Panel Cover. Remove the LED Lens from the Panel Cover. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), Hopper (p 72) Removal procedure 1. Remove all the cables and FFCs connected to the Main Board.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 2. 3. Remove the four screws that secure the Main Board. Remove the Main Board and the Shield Plate with the PE Sensor Lever to the ASF side as shown below. Shield Plate Main board PE Sensor Revision A 4.4.3 Power Supply Unit Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) Removal procedure 1. 2. 3.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4. Remove the screw that secures the Grounding Wire, and remove the Grounding Wire from the Power Supply Unit. Revision A When installing the Power Supply Unit, insert its protrusion to the hole of the Lower Housing, and align the rib and dowel of the Lower Housing with the positioning hole of the Power Supply Unit. Power Supply Unit Grounding Wire SCREW M3x8 P-TITE (5±0.5kgfcm) Terminal Figure 4-24.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5 Disassembling the Printer Mechanism 2. Revision A Release the FFC from the tabs of the Carriage. 4.5.1 Printhead Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) FFC Removal procedure 1. Head FFC Release the Carriage Lock and move the Carriage to the center. Unlocked Locked Tab Figure 4-27.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4. Release the two hooks on both sides of the Carriage with a flathead precision screwdriver or a similar tool, and remove the Holder Contact Assy upward as shown below. 5. Revision A Release the hook, and remove the FFC Cover. FFC Cover hook Rib Figure 4-30. Removing the Printhead (5) Hook C A U T IO N 6. Be careful not to touch the nozzles with bare hands or damage the ink supply needles of the Printhead.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 7. Remove the Head FFC from the connector of the Printhead, and remove the Printhead. Revision A When installing the Contact Assys, secure them to the Holder Contact Assy with two each hooks on the Contact Assys. Front Printhead Contact Assys Hook Figure 4-33. Assembling the Holder Contact Assy (1) When installing the CR Contact Module, secure it with four hooks of the Holder Contact Assy.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.2 CR Scale Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) 4. 5. Revision A Detach the Extension Spring from the Main Frame. Remove the CR Scale from the rib of the Main Frame. Main Frame Removal procedure 1. Release the Carriage Lock and move the Carriage to the center. (See "4.5.1 Printhead (p68)".
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.3 Hopper 2. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) Revision A Release the hook that secures the Edge Guide, and remove the Hopper from the Edge Guide. Hopper Removal procedure 1. Release both the dowels that secure the Hopper, and remove the Hopper and the Compression Spring from the Lower Housing.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.4 PF Encoder/ PF Scale 4.5.5 EJ Roller/ EJ Frame Assy Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) Removal procedure 1. 2. 3.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 2. Insert a flathead precision screwdriver between the EJ Roller Gear and the rib of the EJ Roller, and remove the EJ Roller Gear by pushing it in the direction of the arrow. Revision A When installing the EJ Roller Gear, be sure to align the concave section of the EJ Roller Gear with the convex section of the EJ Roller, then secure them. (See Fig.4-42.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.6 CR Motor/ Driven Pulley 2. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64) 3. Removal procedure 4. C A U T IO N 1. Be careful not to break the soldered portion of the CR Motor.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Route the CR Motor cable through the four hooks and the two grooves of the Lower Housing with some slack to prevent breaking the soldered portions. (See Fig.4-45.) Be sure to install the CR Motor with the groove facing upward. Revision A When installing the Timing Belt to the Pinion Gear of the CR Motor follow the procedure below taking care not to twist the Timing Belt. 1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.7 Ink System 3. Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), CR Motor/ Driven Pulley (p 75) Revision A Insert a flathead precision screwdriver between the Lower Housing and the Pump Assy and push it in the direction of the arrow to release the hook.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6. Pull out the Waste Ink Tube through the rear of the Cap Assy, and remove the Cap Assy. 3. Revision A Release the two hooks, and remove the Pump Assy from the Lower Housing. Cap Assy Point A Ink Tube Pump Assy Hook Pump Assy Figure 4-54. Removing the Pump Assy (2) Figure 4-52. Removing the Cap Assy (4) Pump Assy 1. Pull out the Waste Ink Tube together with the Holder Tube through the Waste Ink Cover.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 DISASSEMBLING THE CAP ASSY When routing the Ink Tube, confirm the following. • Insert point A of the tube carefully into the Cap Assy not to let it pressed. (See Fig.4-52, Fig.4-63) • Align point D with the right edge of the hook on the ASF Unit, then secure it. (See Fig.4-53, Fig.4-63) • Insert the Holder Tube up to point E as shown below, and insert the holder into the Duct Tube End. (See Fig.4-53, Fig.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 3. Release the two hooks of the IS Cap Assy by rotating it to the direction of arrow pulling out the central rib of the assy., and remove the IS Cap Assy from the Case Cleaner. Case Cleaner Revision A When installing the Foam Cap Side, align the notchs of the Foam Cap Side with the ribs of the Case Cleaner, and insert them without any gap. (See Fig.4-60.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 DISASSEMBLING THE PUMP ASSY When assembling the Pump Assy, follow the instructions below. 1. Mark five points on the Ink Tube as shown below. Disassembly Procedure 1. 2. 3. 4. Release the hook of the Pump Housing and remove the Gear Pump Idle. Remove the Gear Pump and Bracket Pump from the Pump Housing. Remove the Roller Pump from the Bracket Pump. Remove the Waste Ink Tube from the Pump Housing.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 3. Secure point C of the tube to the Pump Housing as shown below. Pump Housing Revision A 4.5.8 PF Motor Parts/Components need to be removed in advance: Scanner Stand/ Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), Hopper (p 72), Main Board (p 65) Removal procedure Point C 1. Pull out the PF Motor cable and the Ferrite Core from the hole of the Lower Housing to release them.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 C A U T IO N 3. 4. Do not damage the PF Roller Gear. Do not damage the Pinion Gear. Be careful of not to break the soldered portions. 5. 6. Revision A Remove both the screws that secure the PF Motor. Remove the PF Motor pulling out the shaft of the motor through the notch of the Bracket. Remove the screw that secures the Bracket.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.9 Main Frame 3. Revision A Remove the screw that secures the Bracket. Parts/Components need to be removed in advance: Scanner Stand/ Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), Hopper (p 72), Main Board (p 65) CR Motor/ Driven Pulley (p 75), Ink System (p 77), PF Encoder/ PF Scale (p 73) Bracket Removal procedure C A U T IO N 1. 2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6. Remove the four screws that secure the Main Frame to the Lower Housing. C A U T IO N Front Right 7. Revision A Do not damage the PF Scale and the Lever Pick Clutch with the Main Frame. After removing the Main Frame, do not lay it with the Driven Roller of the Upper Paper Guide facing downward. Remove the Main Frame, the Carriage, and the Upper Paper Guide from the Lower Housing following the procedure below.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.10 Upper Paper Guide Revision A When replacing the PE Sensor Lever, put the long leg of the lever through the hole of the Upper Paper Guide, and secure the thin part of the lever to the bearing of the Upper Paper Guide.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.11 CR Unit Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), Printhead (p 68), CR Motor/ Driven Pulley (p 75) Ink System (p 77), Hopper (p 72), Main Board (p 65) 2. 3. Remove the Main Frame. (See "4.5.9 Main Frame (p84)".) Slide the CR Unit in the direction of the arrow, and remove it from the Main Frame.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6. 7. Remove the two screws that secure the CR Encoder Board, and remove the CR Encoder Board from the Carriage. Remove the Timing Belt from the Carriage. Revision A When installing the FFC to the Carriage, route the FFC as shown below. CR Encoder FFC Backside of Carriage CR Sensor Assy Head FFC FFC Figure 4-82.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Install the FFC according to the following procedures. 1. Lead the FFC through the hole of the Holder FFC and Main Frame. 3. Revision A Fold back the FFC and secure it with rib A again. FFC FFC Holder FFC Rib A Figure 4-86. Installing the CR Unit (5) Hole 4. 5. Figure 4-84. Installing the CR Unit (3) 2. Fold back only the Head FFC and secure it with rib A again. Connect the FFC to the Main Board (J8, J9).
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.12 PF Roller Before installing the PF Roller, align the groove of the PF Roller Shaft with the rib of the Lower Housing. (See Fig.4-89.) Install the Cover Flashing following the procedure below. 1. Insert the hook of the Cover Flashing through beneath the PF Roller into the hole of the Lower Housing. 2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.5.13 LD Roller/ ASF Unit Parts/Components need to be removed in advance: Scanner Stand/Cover Wire (p 60), Scanner Unit (p 62), Middle Housing (p 63) Panel Unit (p 64), Hopper (p 72), Main Board (p 65) CR Motor/ Driven Pulley (p 75), Ink System(p 77), PF Encoder/ PF Scale(p 73) Main Frame (p 84) 4. 5. Revision A Remove the three screws that secure the ASF Unit.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 8. 9. Release the hook of the Combination Gear, and remove the gear from the ASF Housing. Remove the Lever Pick Clutch from the ASF Housing. Revision A When installing the ASF Unit, insert the guide pin of the Lower Housing to the positioning hole of the unit, and secure the unit with the hook of it and the three screws. (See Fig.4-91.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Assemble the LD Roller Assy following the procedure below. 1. Install the Clutch while aligning the guide pin of the LD Roller Shaft with the hole of the Clutch. 2. Install the Extension Spring between the hook of the LD Roller Shaft and that of the Clutch. 3. Install the Combination Gear to the LD Roller Shaft. Revision A 4.5.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 When installing the Waste Ink Pads, align the ribs of the Lower Housing with the notches of the Waste Ink Pads. (See Fig.4-99.) When installing the Diffusion Sheet in the section B, install the Waste Ink Cover and the Waste Ink Pads (x3) in the order shown below.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A When installing the Waste Ink Pad D, make sure to fit it evenly 1.5mm lower than the platen surface of the Lower Housing. If the Lower Housing is contaminated with the liquid of the Waste Ink Pad D, make sure to wipe it off with alcohol. D Lower Housing Figure 4-104.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.6 Disassembling the Scanner Unit 1. 4.6.1 Upper Scanner Housing Revision A Remove the five screws that secure the Upper Scanner Housing and the eight hooks inside the Lower Scanner Housing, and remove the Upper Scanner Housing.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.6.2 Scanner Carriage Unit C A U T IO N Parts/Components need to be removed in advance: Document Cover/ASF Cover (p 59), Scanner Unit (p 62) Upper Scanner Housing (p 96) Removal procedure C A U T IO N 3. Do not scratch the Rod Lens Array when removing the Scanner Carriage Unit. Revision A Take extra care not to contaminate the Scanner Timing Belt with grease on the rail of the Lower Scanner Housing.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6. Disengage the shafts on both ends of the CIS Unit from the bearing holes of the Scanner CR Holder, and remove the unit. Revision A Install the CIS springs (x2) to the dowels of the Scanner CR Holder. (See Fig.4-112.) CIS Unit Dowel Scanner CR Holder Scanner CR Holder Shaft and Shaft hole Figure 4-111. Removing the CIS Unit CIS Spring Figure 4-112.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 4.6.3 Scanner Motor Unit When installing the Scanner Motor Unit, align each dowel at the bottom of the Scanner Housing with their positioning holes of the Scanner Motor Unit. (See Fig.4-114.) Route the Scanner Motor cable through the three ribs and the two protrusions at the bottom of the Scanner Housing. (See Fig.4-114.
CHAPTER 5 ADJUSTMENT Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 5.1 Adjustment Items and Overview This chapter describes adjustments required after the disassembly/reassembly of the printer. C H E C K P O IN T Revision A For information on how to carry out the adjustments and media required for the adjustments, see the instructions displayed by the Adjustment Program. 5.1.1 Servicing Adjustment Item List (TBD) The adjustment items of this product are as follows. Table 5-1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 5-2. Maintenance Items Maintenance Item Purpose Method Outline Tool After replacing the Waste Ink Pad, reset the counter to its default. Waste ink pad counter The printer indicates a maintenance error when the waste ink pad counter reaches its maximum. Use this to reset the counter after replacing the Waste Ink Pad.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 5.1.2 Required Adjustments (TBD) The table below lists the required adjustments depending upon the parts being repaired or replaced. Find the part(s) you removed or replaced, and check which adjustment(s) must be carried out. Table 5-4.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A Table 5-4.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 5.2 Using the Adjustment Program (TBD) This section describes how to judge the adjustment patterns printed by the Adjustment Program. For information on how to operate the Adjustment Program, see the instructions displayed by the Adjustment Program. Revision A 5.2.2 First Dot Position Adjustment The following pattern is printed. 5.2.1 TOP Margin Adjustment The following pattern is printed. Figure 5-2.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 5.2.3 Head Angular Adjustment 5.2.4 Bi-D Adjustment The following pattern is printed. The following pattern is printed for each of the four print modes (four dot size modes). 4 1 2 3 5 4 6 7 1 2 3 Figure 5-3. Head angular adjustment Pattern Printing 8 9 6 Figure 5-4.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 5.2.5 PF Adjustment Revision A How to Judge Examine the printout patterns and enter the value for the pattern without any overlap or gap between the two rectangles. $NCEM 1 Additional Information 2 If overlaps or gaps are observed in all the patterns, enter the value for the best one, and print the adjustment pattern again.
CHAPTER 6 MAINTENANCE Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6.1 Overview 6.1.2 Service Maintenance If any abnormal print (dot missing, white line, etc.) has occurred or the printer indicates the “Maintenance request error” (This error is displayed as “Service Required” in the STM3), take the following actions to clear the error. This section provides information to maintain the printer in its optimum condition. 6.1.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 6.1.3 Lubrication Refer to the following figures for the lubrication points. The type and amount of the grease used to lubricate the printer parts are determined based on the results of the internal evaluations. Therefore, be sure to apply the specified type and amount of the grease to the specified part of the printer mechanism on the following occasion. Driven Pulley Holder The printer is disassembled/assembled.
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 0-digit side Lower Housing Revision A Rib of the Lower Housing (Contact area with the EJ Roller.) G-8AF Adequate dose Before installing the EJ Roller. Use an injector. Make sure to apply whole the rib. Figure 6-3. Lubrication on Lower Housing (2) 80-digit side EJ Roller Contact area with the EJ Roller.
CHAPTER 7 APPENDIX Confidential
Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300 Revision A 7.1 Exploded Diagram / Parts List This manual does not provide exploded diagrams or parts list. For the information, see SPI (Service Parts Information).
