User's Guide CMP0073-00 EN
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Contents Contents Before Printing. . . . . . . . . . . . . . . . . . . . . . . . . . Saving New Media Settings. . . . . . . . . . . . . . . . . Type and Summary of Media Settings. . . . . . . Easy Media Setup Procedure. . . . . . . . . . . . . . Media Adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . Media Adjust (Auto). . . . . . . . . . . . . . . . . . . . Media Adjust (Manual). . . . . . . . . . . . . . . . . .
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Contents Checking for clogged nozzles. . . . . . . . . . . . . . . . Ways to Check for Clogs. . . . . . . . . . . . . . . . . Printing nozzle check patterns. . . . . . . . . . . . . Head Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . Types of Head Cleaning. . . . . . . . . . . . . . . . . Head cleaning procedure. . . . . . . . . . . . . . . . . Long-term Storage (Pre-storage Maintenance). . . Pre-storage Maintenance Timing. . .
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction Introduction Printer Parts Front Section The illustration shows the SC-S60600 Series. A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Around the Print Head” on page 62 B Additional Print Drying System The heater can be used to rapidly dry ink after printing. This is an option for the SC-S80600 Series/SC-S40600 Series.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction E Roll core holder Place the roll core for media take-up on these holders. There are same parts on both the left and the right. U “Using the Auto Take-up Reel Unit” on page 32 F Roll support Rest media temporarily on these supports when removing the take-up roll. There are same parts on both the left and the right. G Auto switch Use this switch to select the auto take-up direction. Choose Off to disable auto take-up.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction P Air filter These filters absorb ink mist as air passes through the printer. The air filters are consumable items. Replace the wiper unit at the same time. U “Replacing Maintenance Parts” on page 70 Q Front cover Open when loading media, cleaning the inside of the printer, or removing jammed media. Normally closed when using the printer. Right view A Airflow vents Allows air to flow into the printer.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction D Casters There are two casters on each leg. Once installation is complete, the front casters should be kept locked while the printer is in use. E Adjusters When installing on a carpeted floor or a sloping floor, check level gauge of the printer and adjust these to keep the printer stable. U Setup Guide F AC inlet #1/AC inlet #2 Connects the power cable. Be sure to connect both cables. G LAN port Connects the LAN cable.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction Inside Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. A Print head The print head prints by moving left and right while emitting ink. Clean at least once a month.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction F Caps Except during printing, these caps cover the print head nozzles to prevent them drying out. The SC-S80600 Series/ SC-S60600 Series has two blocks. Clean at least once a month. U “Cleaning Around the Caps” on page 63 G Wiper unit The wiper removes ink from the surface of the print head nozzles. The wiper unit is a consumable item. Replace when a message is displayed on the control panel prompting you to do so.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction E Pre-heater Heats the media before printing so that the print area is not subject to sudden changes in temperature. F Roll support Rest media on these supports before placing it on the roll holders. There are same parts on both the left and the right. G Handle After placing media on the right roll holder, rotate the handle to press the holder and apply pressure to the roll core.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction C M button (media setup button) Pressing this button displays the Media Setup menu on the screen to perform Feed To Cut Position, Media Remaining, Select Media, Customize Settings, and Easy Media Setup. Control panel U “The Media Setup Menu” on page 93 If you press this while printing, you can adjust the media feed. U “Correcting Banding” on page 51 D Display Displays the printer's status, menus, error messages, and so on.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction H u/d buttons (up and down buttons) ❏ ❏ ❏ L W button (pause/cancel button) When the media loading lever is in a lowered position and the d button is pressed, media is fed. If the u button is pressed, media is rewound. This occurs regardless of the way the loaded media is rolled. Note that when the u button is used to rewind, the media will stop when its edge reaches the starting print position.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction : The heater has reached the selected temperature. : The level of ink remaining has reached the limit. Replace the old ink cartridge with a new one. : The heater has not reached the selected temperature. : The ink cartridge is not latched. Lower the lock lever to engage the latch. : No ink cartridge is inserted. Insert the ink cartridge and lower the lock lever to engage the latch.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction M : Magenta C : Cyan U “Changing the Heater Temperature and Drying Settings” on page 50 Note: You can check E to G in a little more detail from Level on the setup menu. F Waste Ink Bottle status Displays the approximate amount of space available in the Waste Ink Bottle. The display changes as shown below when the waste ink bottle is nearly full or an error occurs.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction Features High Print Quality Realizing High Productivity Smooth Gradations, High-Fidelity Color Reproduction The SC-S80600 Series is equipped for light-colored inks (LK, LC, and LM) to reduce graininess and smooth the gradations. Also, the use of OR and R ink increases the color gamut for high-fidelity color reproduction. Triple Heaters The three heaters listed below support improved productivity and print quality.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction When using the "Epson Control Dashboard" software, you can download and set print setting files (EMX) provided by Epson. An EMX is a print settings file for each media type and includes print information that is necessary to print correctly on commercially available media, such as settings for media registered to the printer, ICC profiles to be used in RIP, the number of passes, and the resolution.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction conditions suit the media. For more information, see the documentation supplied with the media. Also, when operating in dry areas, air conditioned environment, or under direct sunlight, maintain the appropriate humidity. When using WH/MS ink, observe the following points as well.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction ❏ Close all covers before placing the printer in storage. If you are not using the printer for a long time, put an anti-static cloth or cover on the printer to prevent dust. The print head nozzles are very small, and they can become clogged easily if fine dust gets on the print head, and you may not be able to print properly. ❏ Do not leave the printer without ink cartridges installed.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction ❏ Ink cartridges installed in the printer (except for WH and MS) must be removed and thoroughly shaken once every three weeks. WH and MS ink cartridges must be removed and thoroughly shaken every day before starting work. You do not need to shake the Cleaning Cartridge. Shaking ink cartridges U “Shaking” on page 66 Handling Media Note the following when handling or storing media.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction ❏ To prevent discoloration, display and store prints as instructed in the documentation supplied with the media. Shake once every 24 hours Ink cartridges must be removed and thoroughly shaken once every 24 hours. Shaking ink cartridges U “Shaking” on page 66 Notes on Usage of WH/ MS Ink (SC-S80600 Series) Ink cartridge storage Cartridges must be stored flat (that is, laid horizontally on their sides).
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction Introducing the Software The following applications are available for Windows on the supplied software disc. For Mac OS X and computer's without disc drives, you can install the software from http://epson.sn. Install as required. For information about these applications, see the Network Guide (Online Manual) or the on-line help for the application in question. Note: Printer drivers are not provided.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction Starting Epson Control Dashboard You can access Epson Control Dashboard from a computer on the same network as the computer on which it is installed is connected to. Epson Control Dashboard is a Web application. You do not need to install Epson Control Dashboard on the startup computer. A The application can be launched using either of the following two methods.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Introduction B Mac OS X Click Move - Applications - Epson Software EPSON Software Updater. In Windows XP, go to the Control Panel and click Add or Remove Programs. Note: In Windows, you can also start by clicking the printer icon on the desktop toolbar and selecting Software Update. C Go to the Control Panel and click Uninstall a program from the Programs category. C Update the software and manuals.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Notes on Loading Media Basic Operations Caution: Notes on loading media ❏ The heaters and media edge plate may be hot; observe all necessary precautions. Failure to observe the necessary precautions could result in burns. If the following points are not observed when handling media, small amounts of dust and lint may stick to the media surface and cause ink drops in the print results.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations C Loading media While holding the tabs of the media edge plate on both sides, move the plate out of the way toward both edges of the platen. You can check the procedure in a video on YouTube. SC-S40600 Series Video Manual SC-S60600 Series Video Manual SC-S80600 Series Video Manual A Press the P button , and then wait until Load media.is displayed on the screen.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations E Move the roll holder to the set position according to the roll size of the media that will be loaded. Note: The method of placing the roll media varies as follows depending on how media is rolled. Printable Side Out Printable Side In F Tighten the screw until the screw no longer turns. H G I 27 Firmly insert the roll core of the media onto the roll holder.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Note: If the roll of media has an outer diameter which is less than 140 mm, the roll core will not reach the holder when raised using the lift lever. Note: If the roll of media has an outer diameter which is less than 140 mm, the roll core will not reach the holder when raised using the lift lever. Raise it with your hands, and insert the roll core onto the roll holder.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations M Tighten the screw until the screw no longer turns. c Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is still visible even after the handle has been turned fully, rewind the handle. Loosen the roll holder screw on the right side, and then restart from Step 4.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Q S Hold the center of the media in one hand, and pull it straight until it is aligned with the bottom edge of the label on the after heater. Tap lightly on both ends of the media, and check if there is a difference in tension between the left and right sides. If there is a difference in tension, the media becomes loose. Do not pull the media with both hands. This could cause the media to skew or move around.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations T U While holding the tabs of the media edge plate on both sides, move the plate to the top edge edge of the media. Adjust so that the edges of the media are aligned with the center of the round holes in the media edge plates. Print Start Position Right Print Start Position Positions vary with the option selected for Media Size Check, as shown below. The factory default setting is ON.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Using the Auto Take-up Reel Unit Media Size Check OFF: Position indicated on the after heater The Auto Take-up Reel Unit automatically takes up media as it is printed, improving the efficiency of unmanned operation. The Auto Take-up Reel Unit for this printer can take up media in either of the following directions.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Attaching the Roll Core Loading Preparing A Keep the d button pressed until the leading edge of the media reaches the center of the after heater. Use a roll core that is longer than the width of the media. This allows the media to be taken up without protruding from the core. Prepare the supplied paper tape. We recommend this method for attaching media to the roll core due to the following advantages.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations C F Align the roll core holder with the right edge of the media, and tighten the screw. Leave a 10 to 20 cm wide section in the center of the media, and cut at least 25 cm in height from the left and right corners of the media. Cutting the media prevents feeding problems, such as the left and right corners of media being folded and caught at the start of take-up. D Insert the roll core onto the right holder.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Take-up with the Printed Side Facing Out A Cut the paper tape approximately 70 cm in length, and paste it approximately in the center of the media using commercially available adhesive tape. B While pulling the paper tape straight down, wrap it around the roll core from front to back, and affix it using commercially available adhesive tape.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations When there is no paper tape While pulling the center section of the media straight down, affix the media to the take up roll core with commercially available adhesive tape. A c Important: Attach the media to the take up roll core with the media in a taut state. If media is attached in a loose state, the media may move around during take-up.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations E Lower the tension bar until it slightly touches the media. F Confirm that the media is attached without looseness. G If the tension on the left and right of the media is different in the areas shown in the illustration below, the media will not be taken up correctly. When one side is loose, restart the procedure from Step 1. Continue holding down the d button until the media has wrapped around once or twice.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations B D While pulling the paper tape straight down, wrap it around the roll core from back to front, and affix it using commercially available adhesive tape. Lower the tension bar until it slightly touches the paper tape. When there is no paper tape While pulling the center of the media straight down, wrap it around the roll core from back to front, and affix it using commercially available adhesive tape.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations B Press the d button in the control panel to feed enough media for a single wrap around the roll core. C Flip the Auto switch to Off, and hold down the Manual switch to to wrap the media once around the roll core. D Flip the Auto switch to E Lower the tension bar until it slightly touches the media. F Confirm that the media is attached without looseness. .
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Settings for Loaded Media Note: You can confirm differences in tension by lightly tapping both edges of the media as shown in the illustration below. When you have finished loading the media, follow the instructions on the control panel to make settings for the loaded media. 1. Select the media setting number Select the media setting number to which the print settings have been registered. 2.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations U “Saving New Media Settings” on page 45 B Note: Two functions are enabled in Remaining Setup - ON The following two functions give you a rough idea of the amount of media available before printing, making it easier to know when media requires replacement. Use the d/u buttons to select the roll type that matches the loaded roll, and then press the Z button.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Printing the Amount of Media Remaining Cutting Media Caution: By printing the remaining amount on the media being removed, you can check this value the next time the media is loaded and enter the media length. This is useful for accurate management of the amount of media remaining. The remaining amount cannot be printed when Remaining Setup is set to OFF.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations B When using the Auto Take-up Reel Unit, raise the tension bar. C Raise the cutter, and then move it so that the cutter blade fits the cutter grove properly. D If you cannot position your hand correctly due to the front cover, open the front cover and then cut. Set the Auto switch to Off. Take up the cut media completely by operating the Manual switch according to how the media is rolled.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations C Lower the roll onto the roll support. Before Printing To maintain print quality, perform the following inspection before starting work each day. D To prevent the media from sliding off the roll, support the roll at its right end. E Loosen the right roll core holder fixing screw and remove the roll core holder from the roll.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations When Film, Canvas, Textile, or Paper/Others are selected: perform manual media adjustment Visually check the printed adjustment pattern, and then enter the adjustment value. Saving New Media Settings The approximate maximum length of the media required to print the test pattern is given below.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations H Easy Media Setup Procedure Buttons that are used in the following settings Use the d/u buttons to select Auto/Manual for Media Adjust, and then press the Z button. When executing Auto: An adjustment pattern is printed. When auto adjustment is complete, Easy Media Setup is complete and you are returned to the status display screen. When executing Manual: An adjustment pattern is printed.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Measure using a scale of up to 0.5 mm. Select the finest lined pattern (all lines overlap) for both. Select "-1" in the cases shown below. J The screen for entering check results for the adjustment pattern is displayed. When anything except Textile is selected Press the d/u buttons and set the value printed under the pattern selected in group A from step 9, and then press the Z button. L Set B in the same way.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations When changing Advanced Settings after saving media settings Standard Usually, this is selected. Media Adjust (Auto) This option is not displayed when selecting Textile in Media Type. 500mm Pattern This is useful for making accurate print adjustments when printing on uneven media such as canvas or media that bleeds-through easily, such as cloth.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations F G Check the printed adjustment pattern. When Standard is selected Two groups of adjustment patterns, A and B, are printed. Select the pattern with the least amount of overlapping or gaps for each group. Select "0.0" in the cases shown below. The screen for entering confirmation results for the adjustment pattern is displayed.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations D Press the Z button to print the adjustment pattern. Changing settings during printing Wait until printing is complete. E Check the printed adjustment pattern.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations D Correcting Banding When you want to correct banding during printing, perform Feed Adjustment. Press the Z button to display the status display screen. Note: If the setting is changed, the icon is displayed on the control panel screen as shown below. To clear this icon, carry out the following operations. Buttons that are used in the following settings ❏ Restart Feed Adjustment. ❏ Execute Restore Settings.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations A Press the Menu button during printing. B Use the d/u buttons to select Printer Status, and then press the Z button. C Use the d/u buttons to select the item you want to check, and then press the Z button. D The current status is indicated by an icon. E When you press the Z button after checking, the previous screen is displayed. The settings menu will be displayed.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations Printable area The gray area in the illustration below shows the printable area. The arrow indicates the feed direction. The left and right edges of media recognized by the printer varies as shown below according to the Media Size Check settings. Media Size Check ON : The printer automatically detects the left and right edges of the loaded media.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Basic Operations A to D indicates the margins on all four sides. See the following for more details. Margin Position Explanation Available Setting Range A Rear*1 This can be set in RIP. To maintain media feeding accuracy, if the settings are less than 5 mm or more than 17 mm, the settings are switched to 5 mm and 17 mm respectively. 5 to 17 mm B Leading edge*1 This can be set in RIP.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Maintenance When to Perform Various Maintenance Operations Cleaning Locations and Cleaning Timing If you continue to use the printer without cleaning, it could cause clogged nozzles or ink drops to occur. * Right print head only in SC-S40600 Series.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance c Important: The printer contains precision instruments. If any lint or dust adheres to the nozzles on the print head, print quality will decline. Perform regular cleaning more frequently depending on the environment and media being used.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Other maintenance When to perform Operation ❏ Once every three weeks Shaking ink cartridges ❏ Before starting operations for the day (WH/MS only)* U “Shaking” on page 66 ❏ When checking if nozzles are clogged Checking for clogged nozzles ❏ When checking which colors are clogged U “Checking for clogged nozzles” on page 76 ❏ Horizontal stripes or tint unevenness (banding) are appeared.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance What You’ll Need A metal tray (supplied with the printer) Ready the following items before beginning cleaning and replacement. When the supplied parts have been completely used, purchase new consumables. Use when putting cleaning utensils, removed consumables, or ink cleaner moved in the container supplied with the printer. Prepare genuine parts when replacing ink cartridges or performing maintenance.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance ❏ Always use fresh cleaning sticks. Re-using sticks can make stains even harder to remove. Precautions regarding maintenance ❏ Do not touch the tips of the cleaning sticks. Oil from your hands could damage the print head. Note the following points when cleaning and replacing parts. ❏ Do not use water or alcohol to clean around the print head or the caps and so on. Ink congeals when mixed with water or alcohol.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance C Open the front cover. D Soak a soft cloth in water, wring it out thoroughly, and then wipe off any ink, lint, or dust that has adhered to the platen heater. Removing and attaching the media edge plates U “Replacing the media edge plates” on page 73 Carefully remove lint and dust stuck in the groove of the platen. Performing Regular Cleaning Clean the parts in the following order.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Using ink cleaner c Important: ❏ Do not reuse ink cleaner. Using dirty ink cleaner will make staining worse. Only use ink cleaner to clean the parts indicated in the manual. Using ink cleaner on other parts of the printer could damage the product. ❏ Used ink cleaner, cleaning stick, and clean-room wipers are industrial waste. Dispose of them in the same way as for waste inks.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance A Confirm that the printer is on and press the # button. A After the print head moves to the left end of the printer, open the left maintenance cover. B Dampen the cleaning stick with ink cleaner. The Maintenance menu will be displayed. B Use the d/u buttons to select Head Maintenance and press the Z button. C Use the d/u buttons to select Regular Cleaning, and then press the Z button.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance D C Wipe off any adhered ink, lint, and dust from the parts that are indicated by below. Hold the cleaning stick flat and wipe the edges of all the caps. The SC-S80600 Series/SC-S60600 Series has two blocks for the caps. Clean all of the caps. Right print head only in SC-S40600 Series.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance D When ink adheres to the guide section Hold the cleaning stick in a perpendicular orientation, and wipe the outer areas of all the caps. A Dampen the cleaning stick with ink cleaner. B Apply ink cleaner to the guide section, and then wipe it down. U “Using ink cleaner” on page 61 Points to note when cleaning caps Check the following points when cleaning the caps.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance When a film of ink adheres to the guide section When there is lint or dust in the cap Remove using the tip of the cleaning stick or tweezers. If a film-like layer of adhered ink cannot be removed completely using a cleaning stick, remove it using tweezers. If no other parts need to be cleaned, proceed to the following section. If no other parts need to be cleaned, proceed to the following section.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance When there is lint attached to the flushing pad Shaking and Replacing Ink Cartridges Wipe off lint and dust with the tip of a cleaning stick. c Important: Shaking Do not deform the metal section of the top surface. If they are deformed, they may damage the print head.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Shaking method c Important: A Epson recommends the use of genuine Epson ink cartridges. Epson cannot guarantee the quality or reliability of non-genuine ink. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance D Hold the cartridge horizontally and shake it in both directions about 5 cm 15 times in 5 seconds. Disposing of Waste Ink In the case of OR, WH, or MS, shake it well approx. 50 times in 15 seconds. Preparing and Replacement Timing Prepare empty waste ink bottle. is displayed Prepare a new Waste Ink Bottle as soon as possible.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Waste Ink Counter A Remove the Waste Ink Bottle from the Waste Ink Bottle holder. B Insert the waste ink tube into the mouth of the new Waste Ink Bottle and place the Waste Ink Bottle in the holder. The printer uses the waste ink counter to track waste ink and displays a message when the counter reaches the warning level. If you follow the message instructions (Replace waste ink bottle and press .
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance D Check again to confirm that a fresh Waste Ink Bottle is correctly placed and then press the Zbutton to reset the waste ink counter. c Important: Maintenance Counter The printer tracks amounts consumed using the maintenance counter and displays a message when the counter reaches the warning level. c Important: Be sure to confirm that the waste ink tube is inserted in the mouth of the waste ink bottle.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Replacing Maintenance Parts A When the message is displayed, press the Z button. B After the print head moves to the left end of the printer, open the right maintenance cover. C D Place your fingers in the groove on the back of the wiper unit, and tilt it forward a little. Grip the sides, and pull it straight up to lift it out.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance H Lift up the tab on the flushing pad, and remove it. I Insert the two hooks on the flushing pad into the slots on the printer and press the tab down until the pad clicks into place. J After replacing the flushing pad, press the Z button. K Remove both of the new air filters from the packaging. L Grip the air filters and lift them straight out.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance O Check that the air filters are installed, and then press the Z button. Replacement procedure A c Important: Make sure you install the air filters. If the printer is used when the air filters are not installed, sensors may degrade due to mist causing misalignment in print and the printer may malfunction. P Close the maintenance cover, and then press the Z button. Q A confirmation message is displayed on the screen.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance D Insert a new media edge plate into the left edge of the platen. (2) While pressing the tip of the metallic plate against the platen, attach the hooked sections to the front corner of the platen. c Important: You cannot attach the media edge plates from the right. When inserting the plate, check the following two points. (1) Align the white line on the platen with that of the media edge plate.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance E F Check that three hooked sections at the rear of the media edge plate are securely applied as shown below and that they are attached with no gap between the platen and media edge plate. While holding the tabs of each media edge plate on both sides, move both the plates to the left and right edges of the platen respectively. Releasing the tab fixes the media edge plate.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Dispose of items according to local laws and regulations. For example, contract a industrial waste disposal company for disposal. In such cases, submit the “Safety data sheet” to the industrial waste disposal company. Btw Pages Nozzle Check - Auto Nozzle Check This function is useful when making prints continuously while automatically checking nozzles. You can download it at your local Epson Web site.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Printing nozzle check patterns c Important: Always remove clogs from the nozzles of all colors before resuming use. If clogged nozzles (including clogged nozzles for colors that are not used) remain when printing after resuming use, the clogs can no longer be removed. Buttons that are used in the following settings D The menus close when printing is complete.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance continues. If clogging is not cleared even after performing this operation twice, a message asking if you want to continue printing is displayed. U “The Printer Setup Menu” on page 98 All Nozzles Choose this option if all patterns in the printed nozzle check results contain faint or missing segments. After making your selections, proceed to Step 6. Head1/Head2 This is displayed by the SC-S80600 Series/ SC-S60600 Series only.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance SC-S40600 Series/SC-S60600 Series For Pre-storage Maintenance, use the number of cleaning cartridges (CL) (sold separately) shown for each model in the following table. Nozzles are still clogged after performing head cleaning several times The areas around the print heads may be soiled. Perform the following. (1) Perform Auto Head Maintenance from the setup menu.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Performing Pre-storage Maintenance Observe the following cautions when storing the printer and ink cartridges that were removed during use. c Important: U “Notes when not using the printer” on page 18 If the amount of remaining ink or cleaning fluid is insufficient, the function may not run. When there is an insufficient amount remaining, have new cartridges on hand as a precaution.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance * The standard period is indicated, assuming the following usage conditions. What you need: ❏ When changing the spot color to use (WH <= => MS) Ink cartridge of the color you want to change to: 1 Cleaning Cartridge: 1 Note: Eject ink from the tubes and wash them using a Cleaning Cartridge to avoid mixing colors before changing the spot color. ❏ The power always remains turned on.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Cleaning pressure rollers Then, follow the on-screen instructions to replace the cartridge. If you keep using the pressure rollers when they are soiled with ink mist, the print outs will be soiled. Observe the following cautions when storing the ink cartridges that were removed during use. If the rollers are dirty, follow the steps below to clean them.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Carriage rod A c Important: A When wiping, make sure the cloth or your finger does not touch the rod B shown in the illustration. If the cloth or your finger touch the rod, an error could occur during printing.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance C Use the u button to select Grease Carriage Rod, and then press the Z button. c Important: Do not slide the tool back and forth. When Grease kit is needed. Continue? is displayed. Make sure that you have a grease kit ready to use. D Use the u button to select Yes, and then press the Z button. E Insert the tab of the pad A (new) firmly into the rectangular slot on the grease tool and fit the pad to the tool as shown.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance Greasing procedure for carriage rod B A Hold a new pad B firmly against the gray part of the rod as shown in the illustration, and smoothly slide it from the right end to the left end to wipe off stains on the rod. Repeat this action four times. M Hold the pad of the tool as described in step 7, and slide the grease tool back and forth twice. c Important: Do not slide pad B back and forth.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Maintenance ❏ Store the container at room temperature with the cap uppermost in a location that is not exposed to direct sunlight. C Hold pad B as described in step 1, and slide the pad back and forth twice. D Close the front cover, and then press the Z button. The carriage moves back and forth. E Remove the stained pad from the grease tool, and then store the grease tool with the grease.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The menus are used as shown below.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Media Setup For more information on these items, see U “The Media Setup Menu” on page 93.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Head Movement Data Width, Printer Full Width Multi Strike Printing OFF, 2 to 8 Feed Speed Limiter ON, OFF Pressure Roller Load Light, Medium, Heavy Remove Skew ON, OFF Periodic CL Cycle Auto Manual Length Enter Value 1 to 100 When To Clean Between Pages, Middle Of Page Cleaning Level Light, Medium, Heavy Page Between Pages 1 to 100 Cleaning Level Light, Medium, Heavy Restore Se
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Btw Pages Nozzle Check OFF - Print Pattern 1 to 10 Auto Nozzle Check 1 to 10 Lamp Setting Auto, Manual Head Mode*1 2 Heads Mode, Head1, Head2 Sleep Mode 15 to 240 minutes Restore Settings Yes, No Maintenance For more information on these items, see U “The Maintenance Menu” on page 100 Setting items and setting values marked with asterisks indicate the following printer models.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Other maintenance Ink Circulation*2 Execute Ink Refresh*2 Execute Head Washing XX/XX, Head1 XX/XX*3, Head2 XX/XX*3, Head1 All Nozzles*3, Head2 All Nozzles*3, All Nozzles ("XX" indicates an ink color code.) Pre-Storage Maint.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Preferences Date And Time MM/DD/YY HH:MM Language Japanese, English, French, Italian, German, Portuguese, Spanish, Dutch, Russian, Korean, Chinese Units Unit: Length m, ft/in Unit: Temperature °C, F Alert Sound Setting ON, OFF Alert Lamp Setting ON, OFF Reset All Settings Yes, No 92
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Details of the Menu The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button. * indicates default settings. Feed To Cut Position Sends the end of the print to the cutting groove. Easy Media Setup You can quickly and easily register media settings using the Wizard to perform optimum printing according to the size and type of the media being used.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Customize Settings Item Explanation Current Settings To change the currently selected setting, select Current Settings. When changing specific media settings, select the setting number for the target media. 1 to 30 (media setting number) Media setting item The manufacturer settings for each item differ depending on the [Media Type] selected.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Advanced Settings Explanation In most situations, use the value set for each media type as it is. When using special media or when a problem such as head striking or banding is detected in printing results, change the default. Platen Gap 1.6 2.0 2.5 Choose the platen gap (the distance between the print head and the media). The default setting of 1.6 is recommended in most situations.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Media Tension Parameter Explanation Lv1 Increase tension if creases appear in the media during printing. The higher the value, the greater the tension. Lv2 Lv3 Lv4 Media Suction 0 to 10 (4*) When media is waved on the platen, increase the Media Suction. The higher the value, the greater the suction.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Length Sets the frequency for periodic cleaning according to the prints performed. Enter Value 1 to 100 (10*) When To Clean Between Pages* Middle Of Page Cleaning Level Explanation Enter Value performs head cleaning after printing a specific number of meters. When To Clean sets whether or not to perform head cleaning even when the cleaning time is reached during printing.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu The Printer Setup Menu * indicates default settings. Setting items and setting values marked with asterisks (*1) indicate the following printer models. *1:For SC-S80600 Series/SC-S60600 Series only Item Parameter Explanation 3 to 25 mm (5*) Choose the width of the right margin when media is loaded in the printer. See the following for more information.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation OFF - Select how to perform periodic nozzle checks. Print Pattern 1 to 10 (1*) Auto Nozzle Check 1 to 10 (1*) Btw Pages Nozzle Check When this is set to OFF, a nozzle check is not performed between pages. For Auto Nozzle Check, when printing for the set number of pages is complete, the printed check pattern is read by the sensor to confirm that there is no clogging.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Sleep Mode 15 to 240 minutes (15*) The printer enters sleep mode when no errors are detected and no print jobs have been received for a specific time. In sleep mode, all heaters turn off, the control panel turns off, and the internal motors and other components consume less power.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Head Maintenance Auto Head Maintenance If the message Press # and perform Head Maintenance.is displayed on the control panel screen, select Regular Cleaning and perform cleaning. Regular Cleaning U “Performing Regular Cleaning” on page 60 Perform Auto Head Maintenance if nozzles are still clogged and ink drops form even after performing head cleaning.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Pre-Storage Maint. Change Color Mode*2 Parameter Explanation WH*2 Always perform pre-storage maintenance if the printer will not be used for one month or more (and switched off.) MS*2 See the following for more information. All Nozzles U “Long-term Storage (Pre-storage Maintenance)” on page 79 9 Color Items displayed differ depending on the mode currently selected.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu The Preference Menu * indicates default settings. Item Parameter Explanation Auto - Panel IP: XXX.XXX.XXX.XXX Choose whether IP addresses are obtained automatically using DHCP (Auto) or manually (Panel). If Panel is selected, enter an IP address, subnet mask, and default gateway address. Contact your system administrator for detailed information. Network Setup IP Address Setting SM: XXX.XXX.XXX.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Alert Sound Setting ON* Enable (ON) or disable (OFF) the buzzer that sounds when an error occurs. OFF Alert Lamp Setting ON* Enable (ON) or disable (OFF) the alert lamp that lights when an error occurs. OFF Reset All Settings Yes When you select Yes, all settings in the configuration menu, except for the items in Preferences, are returned to their defaults.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages What to do Prepare empty waste ink bottle. The Waste Ink Bottle is getting full. Ready a new Waste Ink Bottle. U “Options and Consumable Products” on page 113 Ink Cartridge Error Ink cartridge cannot be recognized. Insert again or replace ink cartridge.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver Messages What to do Auto Take-up Reel Unit stopped. Media is not correctly attached to the Auto Take-up Reel Unit. Press the W button and select Job Cancel to cancel printing. Flip the Auto switch on the Auto Take-up Reel Unit to the Off position, then flip it back and reattach the media to the Auto Take-up Reel Unit.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver Messages What to do 3 layer printing is only available with 2 Head Mode. SC-S80600 Series/SC-S60600 Series only When one head mode is set, three layered printing cannot be performed. Set two head mode, and then perform three layered printing.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver You cannot print under the network environment. Troubleshooting You cannot print (because the printer does not work) o Ask your network administrator for the network settings. The printer does not turn on. o o Is the power cable plugged into the electrical outlet or the printer? Connect the printer directly to the computer using a USB cable, and then try to print.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver o Is Circulating ink... displayed on the screen of the control panel? o Given that there is a slight gap between the print head and the media, the landing sites for the different colors of ink may be affected by humidity, temperature, inertial forces imparted by the print head, the direction of the print head as it moves from right to left or left to right, or the use of two print heads (all models except SC-S40600 Series).
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver o o Is Data Width selected for Head Movement? o Is the media skewed? Selecting Data Width for Head Movement in the setup menu increases print speed but may slightly reduce print quality. For better quality results, select Printer Full Width for Head Movement. If OFF is selected for Media Skew Check in the setup menu, printing will continue when the media is skewed and data will appear outside the print area.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver o C Is the media too thick or too thin? ❏ Check the media specifications to determine whether it can be used in the printer. U “Supported Media” on page 117 ❏ For information on how to configure print settings using the software RIP, contact the RIP manufacturer. c Important: Cease use of the printer if the media edge plates are deformed. Continued use could damage the pressure rollers or print head.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Problem Solver F Pull the media to the cutter groove and use a cutter to remove torn or creased portions. Others Heaters Turn off or the Optional Additional Print Drying System Stops. o The pre-, platen, and after heaters will turn off if no print job is received for some time and no error occurs. The time before the heaters automatically switch to OFF can be selected using the Sleep Mode option in the setup menu.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Appendix Options and Consumable Products The following options and consumable products are available for use with this printer. (As of November 2015) For the latest information, see the Epson Web site.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Printer model Product SC-S80610 Ink cartridges SC-S80670 Ink cartridges Part number Black T8911 Cyan T8912 Magenta T8913 Yellow T8914 Light Cyan T8915 Light Magenta T8916 Light Black T8917 Orange T8918 Red T8919 White T891A Metallic Silver T891B Black T8921 Cyan T8922 Magenta T8923 Yellow T8924 Light Cyan T8925 Light Magenta T8926 Light Black T8927 Orange T8928 Red T8929 White T892A Me
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Printer model Product SC-S80680 Ink cartridges SC-S40600 SC-S60600 SC-S40600 SC-S60600 (Australia and New Zealand) SC-S40610 SC-S60610 SC-S40670 SC-S60670 SC-S40680 SC-S60680 Ink cartridges Ink cartridges Ink cartridges Ink cartridges Ink cartridges Part number Black T8931 Cyan T8932 Magenta T8933 Yellow T8934 Light Cyan T8935 Light Magenta T8936 Light Black T8937 Orange T8938 Red T8939 White T893A
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Epson recommends the use of genuine Epson ink cartridges. Epson cannot guarantee the quality or reliability of nongenuine ink. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior. Information about non-genuine ink levels may not be displayed, and use of non-genuine ink is recorded for possible use in service support.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Supported Media Moving and Transporting the Printer The following media can be used with the printer. This section describes how to move and transport the product. Print quality is greatly affected by the type and quality of media used. Choose a media suited to the task at hand. For information on use, refer to the documentation supplied with the media or contact the manufacturer.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix E Post-Move Setup Unlock the two casters at the front. After moving the printer, follow the steps below to ready it for use. A Check that the location is appropriate for installation, and set up the printer. U Setup Guide If you do not have the Setup Guide, contact your dealer or Epson Support.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Media Settings List for Each Media Type The following table shows the media settings registered when a media type is selected. Media Type Item Adhesive Vinyl Banner Film Canvas Textile Paper/ Others Platen Gap 1.6 2.0 1.6 2.0 2.0 1.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix System Requirements (Epson Control Dashboard) The Epson Control Dashboard can be used under the following environments. c Important: Make sure the computer on which the Epson Control Dashboard is installed meets the following requirements. If these requirements are not met, the software cannot monitor the printer correctly. ❏ Disable your computer's hibernate function.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Specifications Table Printer Specifications Power consumption Printer Specifications SC-S80600 Series (total for numbers 1 and 2) Printing: Approx. 650 W Printing method On-demand ink jet Ready mode: Approx. 380 W Nozzle configuration SC-S80600 Series: Sleep mode: Approx.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Appendix Printer Specifications Dimension Ink Specifications SC-S60600 Series Storage temperature Storage dimensions: 2620 (W) x 972 (D) x 1338 (H) mm Uninstalled: -20 to 40°C (within 4 days at -20°C, within a month at 40°C) Installed: -20 to 40°C (within 4 days at -20°C, within 4 days at 40°C) Maximum dimensions: 2620 (W) × 1147 (D) × 1670 (H) mm SC-S80600 Series/SC-S40600 Series Transporting: -20 to 60°C (within 4 days at -20°C, with
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Where To Get Help Contacting Epson Support Technical Support Web Site Before Contacting Epson If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting information in your product documentation, contact Epson support services for assistance. If Epson support for your area is not listed below, contact the dealer where you purchased your product.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Help for Users in North America Help for Users in Europe Epson provides the technical support services listed below. Check your Pan-European Warranty Document for information on how to contact Epson support. Internet Support Help for Users in Taiwan Visit Epson’s support website at http://epson.com/ support and select your product for solutions to common problems.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Telephone number Fax number Address Your Dealer 03-4393119 03-4396589 5F., No.2, Nandong Rd., Pingzhen City, Taoyuan County 32455, Taiwan (R.O.C.) Don’t forget that your dealer can often help identify and resolve problems. The dealer should always be the first call for advise on problems; they can often solve problems quickly and easily as well as give advise on the next step to take. 03-5325077 03-5320092 1F.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Service Center: World Wide Web (http://www.epson.com.sg) Information on product specifications, drivers for download, Frequently Asked Questions (FAQ), Sales Enquiries, and Technical Support via e-mail are available. 80 Truong Dinh Street, District 1, Hochiminh City Vietnam Help for Users in Indonesia Contacts for information, support, and services are: Epson HelpDesk (Phone: (65) 6586 3111) World Wide Web (http://www.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Yogyakarta Hotel Natour Garuda Jl. Malioboro No. 60 Yogyakarta Help for Users in Malaysia Contacts for information, support, and services are: Phone: (62) 274-565478 Medan World Wide Web (http://www.epson.com.my) Wisma HSBC 4th floor Jl. Diponegoro No.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Where To Get Help Information on product specifications, drivers for download, Frequently Asked Questions (FAQ), and E-mail Enquiries are available.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs"). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms 1.6 "Modifications" mean any addition to, deletion from, and/or change to, the substance and/or structure of the Original Code, any previous Modifications, the combination of Original Code and any previous Modifications, and/ or any respective portions thereof.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms 2.3 Distribution of Executable Versions. In addition, if You Externally Deploy Covered Code (Original Code and/ or Modifications) in object code, executable form only, You must include a prominent notice, in the code itself as well as in related documentation, stating that Source Code of the Covered Code is available under the terms of this License with information on how and where to obtain such Source Code. 2.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies. You expressly acknowledge and agree that use of the Covered Code, or any portion thereof, is at Your sole and entire risk.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms (c) automatically without notice from Apple if You, at any time during the term of this License, commence an action for patent infringement against Apple; provided that Apple did not first commence an action for patent infringement against You in that instance. 12.2 Effect of Termination.
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms Les parties ont exigé que le présent contrat et tous les documents connexes soient rédigés en anglais. EXHIBIT A. "Portions Copyright (c) 1999-2003 Apple Computer, Inc. All Rights Reserved. This file contains Original Code and/or Modifications of Original Code as defined in and that are subject to the Apple Public Source License Version 2.0 (the 'License').
SC-S80600 Series/SC-S60600 Series/SC-S40600 Series User's Guide Software License Terms 3. Altered versions--including, but not limited to, ports to new operating systems, existing ports with new graphical interfaces, versions with modified or added functionality, and dynamic, shared, or static library versions not from Info-ZIP--must be plainly marked as such and must not be misrepresented as being the original source or, if binaries, compiled from the original source.
