PowerLite® Home Cinema 1450 User's Guide
Contents PowerLite Home Cinema 1450 User's Guide............................................................................................. 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents..........................................................
Connecting to a Component Video Source ............................................................................... Connecting to a Composite Video Source ................................................................................ Connecting to a Video Source for Sound .................................................................................. Connecting to an External Computer Monitor................................................................................
Using Basic Projector Features ............................................................................................................... 75 Turning On the Projector .................................................................................................................... 75 Using the Home Screen................................................................................................................. 77 Turning Off the Projector .........................................................
PC Free Display Options ............................................................................................................. 109 Adjusting Projector Features ................................................................................................................. Shutting Off the Picture and Sound Temporarily .............................................................................. Stopping Video Action Temporarily .......................................................................
Projector Information Display - Info Menu ........................................................................................ 152 Event ID Code List....................................................................................................................... 153 Projector Reset Options - Reset Menu ............................................................................................. 154 Maintaining and Transporting the Projector .........................................................
Solving Projector or Remote Control Operation Problems ............................................................... 184 Solutions to Projector Power or Shut-Off Problems ..................................................................... 184 Solutions to Problems with the Remote Control........................................................................... 185 Solutions to Password Problems .................................................................................................
PowerLite Home Cinema 1450 User's Guide Welcome to the PowerLite Home Cinema 1450 User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• Screen Fit feature automatically resizes images for your projection screen • Epson's Instant Off and Direct Power On features for quick setup and shut down • Powerful 16W speaker system Product Box Contents Additional Components Additional Projector Software and Manuals Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector.
6 Projector software CD Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you to connect to the projector.
Additional Projector Software and Manuals After connecting and setting up the projector, install the projector software from the included software CD, or download the software and manuals as necessary. You can install the projector software programs listed here and view their manuals for instructions on using them. Note: If you still need help after checking this manual and the sources listed here, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
Warranty and Registration Information Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure that came with your projector. In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for details.
Related references Where to Get Help Projector Part Locations Check the projector part illustrations to learn about the parts on your projector.
3 Foot release lever 4 Front adjustable foot 5 A/V Mute slide 6 Remote control receiver 7 Sensor 8 Wireless LAN light 9 Air filter cover/intake vent 10 Air filter cover latch 11 Illumination sensor 12 Control panel 13 Focus Help button 14 Zoom ring 15 Screen Fit button 16 Focus ring 17 Lamp cover 18 Status lights Parent topic: Projector Part Locations Projector Parts - Rear 17
1 Computer1 port 2 RS-232C port 3 Audio1 port 4 Computer2/Monitor Out port 5 Audio2 port 6 Audio Out port 7 AC input 8 L-Audio-R ports 9 Security lock slot 10 Remote receiver 11 HDMI2 port 12 HDMI1/MHL port 13 Video port 14 USB-B port 15 USB-A port 16 Network LAN port Parent topic: Projector Part Locations 18
Projector Parts - Base 1 Ceiling mount holes (3) 2 Security cable attachment point 3 Rear feet 4 Front adjustable foot Parent topic: Projector Part Locations 19
Projector Parts - Control Panel 1 Power button 2 Home button 3 Source Search button (searches for connected video sources) 4 Enter button (selects options) 5 Vertical keystone adjustment buttons (displays the adjustment screen and adjusts screen shape) and arrow buttons 6 Esc button (cancels/exits functions) 7 Volume buttons (adjusts speaker volume), horizontal keystone adjustment buttons, and arrow buttons 8 Menu button (accesses projector menu system) Parent topic: Projector Part Location
Projector Parts - Remote Control 1 Power button 21
2 Computer button (cycles through connected computer sources) 3 HDMI/Video button (cycles through connected HDMI/video sources) 4 Screen Fit button (adjusts image shape) 5 Numeric buttons (enter numbers) 6 Auto button (automatically adjusts position, tracking, and sync settings) 7 Aspect button (selects the image aspect ratio) 8 Num button (when held down, switches numeric buttons to number function) 9 Menu button (accesses projector menu system) 10 Arrow buttons (move through on-screen opt
29 Remote control signal emitter (emits remote control signals) Parent topic: Projector Part Locations 23
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
16:10 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 50 inches 66 to 109 inches –1 inch (–2 cm) (168 to 277 cm) 80 inches 107 to 175 inches –1.5 inches (–4 cm) (271 to 445 cm) 100 inches 134 to 219 inches –1.9 inches (–5 cm) (340 to 557 cm) 150 inches 201 to 329 inches –2.
Connecting to a Computer for USB Video and Audio Connecting to a Computer for VGA Video Connecting to a Computer for HDMI Video and Audio Connecting to a Computer for USB Mouse Control Connecting to a Computer for Sound Parent topic: Projector Connections Connecting to a Computer for USB Video and Audio If your computer meets the system requirements, you can send video and audio output to the projector through the computer's USB port (preferably USB 2.0).
• Mac: The USB Display setup folder appears on your screen. Select USB Display Installer and follow the on-screen instructions to install the Epson USB Display software. Follow any on-screen instructions. You need to install this software only the first time you connect the projector to the computer. The projector displays the image from your computer's desktop and outputs sound, if your presentation contains audio.
Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port. 1.
1. Connect the USB cable to your projector's USB-B port. 2. Connect the other end to any available USB port on your computer. 3. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details.
2. Connect the other end to the Audio port that corresponds to the Computer port you are using. Parent topic: Connecting to Computer Sources Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
2. Connect the other end to one of the projector's HDMI ports. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers. Note: If you have problems hearing audio through the HDMI connection, you can use one of the projector's audio ports instead to play sound. Connect one end of an optional 3.
3. Connect the other end of the cable to the projector's HDMI1/MHL port. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers. Parent topic: Connecting to Video Sources Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable.
Note: If you choose the Computer2 port, you may need to change the Monitor Out Port setting in the projector's Extended menu. 3. Tighten the screws on the VGA connector. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Signal menu.
If you are projecting video using a Computer port, connect the projector to the video source using an optional stereo mini-jack audio cable. If you are projecting video using the Video port, connect the projector to the video source using an RCA audio cable. Note: If you connected your video source to the projector using an HDMI cable, the audio signal is transferred with the video signal; you do not need an additional cable for sound. 1. Connect the audio cable to your video source's audio-out ports. 2.
• Connect the red and white plugs on the other end of the cable to the projector's L-Audio-R ports. Parent topic: Connecting to Video Sources Connecting to an External Computer Monitor If you connected a computer to the projector's Computer port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible.
Note: If you do not see an image on the external monitor, you may need to change the Monitor Out Port setting in the Extended menu. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting to External Speakers To enhance the sound from your presentation, you can connect the projector to external self-powered speakers. You can control the volume using the projector's remote control. You can also connect the projector to an amplifier with speakers.
Related references Projector Setup Settings - Extended Menu Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
Connecting a USB Device or Camera to the Projector You can connect your USB device or camera to the projector's USB-A port and use it to project images and other content. 1. If your USB device came with a power adapter, plug the device into an electrical outlet. 2. Connect the USB cable (or USB flash drive or USB memory card reader) to the projector's USB-A port. Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly. 3.
2. Disconnect the USB device or camera from the projector. Parent topic: Connecting to External USB Devices Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover. 2. Insert the batteries with the + and – ends facing as shown.
3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Setting Up the Projector Opening the Lens Cover To open the projector's lens cover, slide the A/V Mute slide lever until it clicks into the open position.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Registering a Digital Certificate on the Projector Wired Network Projection You can project through a wired network.
2. Connect the other end of the cable to the projector's LAN port. Parent topic: Wired Network Projection Selecting Wired Network Settings Before you can project from computers on your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in Epson Web Control. (Default user name is EPSONREMOTE; default password is guest.) • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
8. If necessary, select IP Settings and press Enter. 9. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting. • If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter. 10.
Parent topic: Using the Projector on a Network Related references Additional Projector Software and Manuals Optional Equipment and Replacement Parts Installing the Wireless LAN Module To use the projector over a wireless network, install the optional Epson 802.11b/g/n wireless LAN module. Do not install any other type of wireless LAN module. Caution: Never remove the module while its indicator light is blue or flashing, or while you are projecting wirelessly. You may damage the module or lose data. 1.
3. Remove the screw securing the wireless LAN module stopper, then remove the stopper. 4. Insert the wireless LAN module into the port.
5. Replace the wireless LAN module stopper and secure it using the screw you removed. 6. Close the air filter cover. 7. Plug in and turn on the projector. Parent topic: Wireless Network Projection Using a QR Code to Connect a Mobile Device After you select the wireless network settings for your projector, you can display a QR code on the screen and use it to connect a mobile device using the Epson iProjection app. Note: Make sure you have installed the latest version of Epson iProjection on your device.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus.
7. Do one of the following: • Press the LAN button on the remote control. • Select Display the QR Code in the projector's Network menu. • Press the Home button on the remote control and select Display the QR Code on the Home screen. Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8. Start Epson iProjection on your mobile device. 9.
3. Insert the USB key into the projector's USB-A port. You see a projected message that the network information update is complete. 4. Remove the USB key. 5. Insert the USB key into a USB port on your computer. Note: In Windows Vista, if you see the AutoPlay window, select Run MPPLaunch.exe, then select Allow on the next screen. 6. Follow the on-screen instructions to install the EasyMP Multi PC Projection software. Note: If you see a Windows Firewall message, click Yes to disable the firewall.
Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Make sure the Wireless LAN Power setting is set to On. 5. Select Network Configuration and press Enter.
6. Select the Basic menu and press Enter. 7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in the Epson Web Control.
• Display LAN Info lets you select how the projector displays network information. You can select an option to display a QR code that lets you quickly connect your iOS or Android devices using the Epson iProjection app. Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press Enter to select them. 8. Select the Wireless LAN menu and press Enter. 9.
Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you connect to multiple smartphones, tablets, or computers directly Advanced: lets you connect to multiple smartphones, tablets, or computers via a wireless network access point Search Access Point To Search View Search for available wireless network access points in Advanced connection mode SSID Up 32 alphanumeric characters Sets the SSID (network name) of t
Setting Options Description Channel 1ch In Quick connection mode, selects the frequency band (channel) used by the wireless LAN 6ch 11ch IP Settings DHCP IP Address Subnet Mask Gateway Address SSID Display On Selects whether to display the SSID on the network standby screen Off IP Address Display On Selects whether to display the IP address on the network standby screen Off IPv6 Settings Turns on DHCP if your network assigns addresses automatically; set to Off to manually enter the network's
Selecting Wireless Network Settings on Mac Before connecting to the projector, select the correct wireless network on your Mac. 1. Click the AirPort icon on the menu bar at the top of the screen. 2. Make sure AirPort is turned on, then do one of the following: • If your projector is set up on an existing network (Advanced mode), select the network name (SSID). • If your projector is configured for Quick mode, select the projector's SSID.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Wireless LAN menu and press Enter. 6. Set the Security setting to match your network settings.
7. Do one of the following depending on the network security setting you selected: • WPA2-PSK or WPA/WPA2-PSK: Select Complete and follow the on-screen instructions to save your settings and exit the menus. Skip the remaining steps. • WPA2-EAP or WPA/WPA2-EAP: Select EAP Method and press Enter. 8. Select your authentication protocol as the EAP Type setting. 9. To import your certification, select the certificate type (either Client Certificate or CA certificate) and press Enter.
15. Set the following EAP settings as necessary: • User name lets you enter a user name up to 64 alphanumeric characters long. To enter more than 32 characters, use your web browser. • Password lets you enter a password up to 64 alphanumeric characters long when using the PEAP, EAP-FAST, or LEAP protocols. To enter more than 32 characters, use your web browser. • Verify Server Cert. lets you select whether or not to verify the server certificate when a CA certificate has been set. • RADIUS Serv.
4. Select the Notifications menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server setting. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7. Select a number for the SMTP server Port Number setting, from 1 to 65535 (default is 25). 8. Enter the sender's email address as the From setting. 9.
Network Projector E-mail Alert Messages Parent topic: Using the Projector on a Network Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you receive an e-mail containing the following information: • The email address entered as the From setting • Epson Projector on the subject line • The name of the projector experiencing a problem • The IP address of the affected projector • Detailed information about the problem Note: If a
4. Select the Notifications menu and press Enter. 5. Turn on the SNMP setting. 6. Enter up to two IP addresses to receive SNMP notifications as the Trap IP Address setting, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
7. Select the Others menu and press Enter. 8. If you want to use the Secure HTTP protocol to encrypt communication when using Web Control, turn on the Secure HTTP setting and import the web server certificate using the Web Server Cert. setting. 9. If available, select the Priority Gateway setting for your network. 10. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected. 11.
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely. Note: The web setup and control features support Microsoft Internet Explorer 9.0 or later, and Safari on networks that do not use a proxy server for connection.
You see the Web Control screen. 4. To select projector menu settings, select the name of the menu and follow the on-screen instructions. Note: You may need to log in to access some of the options on the Web Control screen. If you see a log in window, enter your user name and password. (The default user name is EPSONWEB and the default password is admin.) 5. To control projection remotely, select the Basic Control option. Note: If you see a log in window, enter your user name and password.
You see a screen like this: 1 Power button control 2 Selects the HDMI1 port source 3 Selects the HDMI2 port source 4 Selects Video port source 5 Selects the USB Display source 6 A/V Mute button control 7 Freeze button control 8 Page Up and Page Down button controls 9 Displays closed captions 10 Displays a QR code 11 Volume button controls 12 Selects the USB device source 69
13 Selects the network source 14 Selects the Computer1 port source 15 Selects the Computer2 port source 16 Searches for connected sources 6. Select the icon corresponding to the projector function you want to control.
7. Select the Web Server Cert. setting and press Enter. 8. Select Register and press Enter. 9. Follow the on-screen instructions to connect a USB flash drive to the projector's USB-A port. 10. Press Enter to display the certificate list. 11. Select the certificate you want to import from the displayed list. A message is displayed prompting you to enter the password for the certificate. 12. Enter the password and press Enter. The certificate is imported and a completion message appears.
You see the Web Control screen. 5. Select Advanced. Note: You may need to log in to access some of the options on the Web Control screen. If you see a log in window, enter your user name and password. (The default user name is EPSONWEB and the default password is admin.) 6. Under Network, select Manage Certificates. 7. Click the Browse button, select the certificate file, and click Open. 8. Enter a password in the Password box. 9.
Parent topic: Registering a Digital Certificate on the Projector Related references Digital Certficate Types Digital Certficate Types You can register these types of digital certificates.
Specification Description Encryption RSA Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512 Key length 512/1024/2048/4096 bit Common name Network host name Organization Optional Password Up to 32 alphanumeric characters; required Parent topic: Registering a Digital Certificate on the Projector 74
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's On/Standby light turns blue. This indicates that the projector is receiving power. 4. Press the power button on the projector or the remote control to turn on the projector. The projector beeps and the Status light flashes blue as the projector warms up.
• Press the Source Search button on the projector or remote control to detect the video source. • Press the button for the video source on the remote control. • If the Home screen is displayed, select the source you want to project. Using the Home Screen Parent topic: Using Basic Projector Features Related tasks Selecting an Image Source Using the Home Screen You can select input sources and other frequently used options from the Home screen. 1.
1 Select the video source you want to project 2 Display the QR code 3 Display the Help screen 4 Display the projector's menus 5 Select customizable menu options 6 Project two images from different image sources simultaneously 7 Correct the image shape Note: Your Home screen may look different from the illustration shown here. You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3.
The projector displays a shutdown confirmation screen. 2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). 3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status light is on or flashing. 4. Close the projector's lens cover. Parent topic: Using Basic Projector Features Related references Projector Light Status Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image.
2. To adjust the front foot, pull up on the foot release lever and lift the front of the projector. The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape.
When you turn on automatic keystone correction in your projector's Settings menu, your projector automatically corrects keystone effects when you reposition the projector.
3. Zoom into the image until its yellow frame extends beyond the edges of the screen. 4. Press the Screen Fit button again. Two displays flash briefly, then this message appears: 5. Fine-tune the image shape as necessary using the arrow buttons on the control panel. 6. When you are finished, press Esc. Now, if necessary, you can correct the image corners individually using Quick Corner by pressing the arrow buttons on the control panel.
Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the keystone correction buttons on the projector to correct the image shape. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button). 2.
3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the H/V-Keystone settings in the projector menus.
Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the Quick Corner setting to correct the image shape. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: 6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter.
7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button). 2.
2. To sharpen the image focus, rotate the projector’s focus ring. Parent topic: Using Basic Projector Features Focusing the Image with Focus Help You can use the projector's Focus Help feature to focus the image. Focus Help works in these conditions: • Screen size is 100 inches (254 cm) or less • Projection distance is between 4.9 to 9.8 feet (1.5 to 3.0 m) • Projection angle is not more than 20º horizontally or 30º vertically away from the center of the screen • The room is not too bright 1.
You see a screen like this: 2. Turn the focus ring until the two orange circles overlap. 3. When you are finished, press Esc or Focus Help to exit.
Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here. 1 26 feet (8 m) 2 ± 45° 3 ± 30° 4 15° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands.
Using the Remote Control as a Wireless Mouse You can use the projector's remote control as a wireless mouse so you can control projection at a distance from the computer. Note: This function does not work when you project from a device connected using an MHL cable. 1. Connect the projector to a computer using the projector's USB-B, Computer, or HDMI port to display video. 2.
Using the Remote Control as a Pointer You can use the projector's remote control as a pointer to help you call out important information on the screen. The default pointer shape is an arrow, but you can select an alternative shape using the Settings menu. 1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen.
1. Make sure the connected image source you want to use is turned on. 2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Source Search button on the projector or remote control until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
• Press the Home button on the remote control and select your image source. Note: Your Home screen may look different from the illustration shown here. Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen.
Changing the Projection Mode Using the Remote Control You can change the projection mode to flip the image over top-to-bottom. 1. Turn on the projector and display an image. 2. Hold down the A/V Mute button on the remote control for five seconds. The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for five seconds again.
3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio.
2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3. To cycle through the available aspect ratios for your input signal, press the Aspect button repeatedly. Note: If you are projecting from a computer and parts of the image are cut off, set the Resolution setting to Wide or Normal in the Signal menu.
Aspect ratio setting Description Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. Native Displays images as is (aspect ratio and resolution are maintained). Note: The Auto aspect ratio setting is available only for HDMI image sources.
3. Press the Color Mode button on the remote control to change the Color Mode. The image appearance changes and the name of the Color Mode appears briefly on the screen. 4. To cycle through all the available Color Modes for your input signal, press the Color Mode button repeatedly.
3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. You cannot change the Auto Iris setting when you are using a Closed Caption setting. 5. Press Menu or Esc to exit the menus.
2. To lower or raise the volume, press the Volume buttons on the remote control or control panel. 3. To set the volume to a specific level for an input source, use the projector menus. Parent topic: Using Basic Projector Features Projecting a PC Free Presentation You can use your projector's PC Free feature whenever you connect a USB device that contains compatible files. This lets you quickly and easily display the contents of the files and control their display using the projector's remote control.
File type and extension Details Image (.jpg) Make sure the file is not: • CMYK format • Progressive format • Highly compressed • Above 8192 × 8192 resolution Image (.bmp) Make sure the file resolution is not above 1280 × 800 Image (.gif ) Make sure the file is not: • Above 1280 × 800 resolution • Animated • Interlaced Image (.png) Make sure the file resolution is not above 1280 × 800 Document or image (.pdf) Make sure the file is not: • Saved in PDF version 1.
1. Press the USB button on the projector remote control. The PC Free screen appears. 2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter.
4. While projecting, use the following commands to control the display as necessary: • To rotate a displayed image, press the up or down arrow button. • To move to the next or previous image, press the left or right arrow button. 5. To stop the display, follow the on-screen instructions or press the Esc button.
• To view additional files in a folder, highlight Next page or Previous page and press Enter. 3. To display the first page of a PDF file at full size, press the arrow buttons to highlight the file and press Enter. (Press the Esc button to return to the file list screen.) Note: If any file names are longer than 8 characters or include unsupported symbols, the file names may be shortened or changed only in the screen display. If a PDF file extension is not .pdf, the file does not appear in the file list. 4.
The PC Free screen appears. 2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter. 3. To play back a movie, press the arrow buttons to highlight the file and press Enter.
PC Free Display Options You can select these display options when using the projector's PC Free feature.
Setting Options Description Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variety of effects Parent topic: Projecting a PC Free Presentation 110
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
Parent topic: Adjusting Projector Features Related references Projector Setup Settings - ECO Menu Related tasks Saving a User's Logo Image to Display Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1. Press the Freeze button on the remote control to stop the video action. 2.
1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into. • Press the E-Zoom + button repeatedly to zoom into the image area, enlarging it as necessary. • To pan around the zoomed image area, use the arrow buttons.
Password Security Types You can set up these types of password security using one shared password: • Power On Protection password prevents anyone from using the projector without first entering a password. • User's Logo Protection password prevents anyone from changing the custom screen the projector can display when it turns on or when you use the A/V Mute feature. The presence of the custom screen discourages theft by identifying the projector’s owner.
4. Press and hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again. You see the message "Password accepted." 6. Press Esc to return to the menu. 7. Make a note of the password and keep it in a safe place in case you forget it.
If you do not see this menu, hold down the Freeze button on the remote control for about seconds or until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On, press Enter again, and press Esc. 2. To prevent changes to the User's Logo screen or related display settings, select User's Logo Protection, press Enter, select On, press Enter again, and press Esc. 3.
1. Press and hold down the Num button on the remote control while you enter the password using the numeric buttons. Note: The default password is 0000. The password screen closes. 2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support.
Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature). This transferred image is called the User's Logo screen. The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in identifying the projector's owner to help deter theft.
You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12. Select when you want to display the User's Logo screen: • To display it whenever there is no input signal, select Display Background and set it to Logo.
2. Select the Settings menu and press Enter. 3. Select Lock Setting and press Enter. 4. Select the Control Panel Lock setting and press Enter. 5. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 6. Select Yes and press Enter.
• Use the security slot on the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture. Note: Do not pass drop-prevention cables through the security cable attachment point when mounting the projector on a wall or ceiling.
3. Select the Multi-Projection setting and press Enter. 4. Select Projector ID and press Enter. 5. Press the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter. Repeat these steps for all the other projectors you want to operate from one remote control. Note: If you don't know the projector's ID, aim the remote control at the projector and press the ID button to temporarily display the projector's ID on the screen.
2. Make sure you know the projector's ID number as set in the Extended menu Projector ID setting. Note: If you have forgotten the projector's ID, aim the remote control at the projector and press the ID button to temporarily display the projector's ID on the screen. If you turn off the Projector ID setting, the remote control will operate the projector regardless of the ID selected on the remote. 3. Aim the remote control at that projector. 4.
You see this screen: Note: Press Enter to toggle between the projected image and the adjustment screen. 5. Set the Adjustment Level setting to 1 and press Enter. 6. Set the remote control ID to match the second projector. 7. Access the Extended menu Color Matching setting on the second projector and set the Adjustment Level setting to 1. 8. Adjust the color tone settings for Red, Green, and Blue on both projectors in the same way. 9.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other. You can control the split screen feature using the remote control or the projector menus. Note: While you use the split screen feature, other projector features may not be available and some settings may be automatically applied to both images.
1. Press the Split button on the remote control. The currently selected input source moves to the left side of the screen. 2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter, select the input source, select Execute, and press Enter. (You can also change image sources, if necessary.) 4. To switch the images, select the Swap Screens setting and press Enter. 5.
6. To choose the audio you want to hear, select the Audio Source setting, press Enter, select an audio option, press Enter, and press Menu to exit. 7. To exit the split screen feature, press the Split or Esc button. Input Sources for Split Screen Projection Parent topic: Adjusting Projector Features Input Sources for Split Screen Projection You can choose from the input source combinations listed here for split screen projection.
• Projection distance is between 4.9 to 11.2 feet (1.5 to 3.4 m) • Projection angle is not more than 20º horizontally or vertically away from the center of the screen • If you are using a Screen Mirroring connection, you selected operation permissions that allow a connected device's keyboard or mouse to control the projector (Windows 10 only) 1. Connect the projector to a computer using a cable or network connection. 2.
Note: You can change the position of the arrows using the Marker Position setting. 6. Do one of the following: • To move to the next slide or page, cover the up arrow with your hand • To move to the previous slide or page, cover the down arrow with your hand Note: When you are not using the arrows, stand away from them to avoid accidentally covering them. 7. Do one of the following to exit Gesture Presenter: • Press the Gesture button.
You see a screen like this: 4. Select the Schedule menu and press Enter. 5. Select Add New and press Enter. You see a screen like this: 6. In the Event Settings section, select the events you want to have occur. (Select No Change for events that you do not want to occur.) 7. In the Date/Time Settings section, set the date and time for the scheduled events to occur.
8. When you are finished, select Save and press Enter. 9. To schedule more events, repeat the previous steps as necessary. 10. Select Setup complete and select Yes to save your changes. Parent topic: Scheduling Projector Events Viewing Scheduled Events You can view any currently scheduled events. 1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Schedule Settings setting and press Enter.
1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Schedule Settings setting and press Enter. You see a screen like this: 4. Press the left or right arrow buttons to highlight the date on the calendar containing the scheduled event you want to edit. 5. Press the up or down arrow buttons to highlight the event you want to edit, and press Esc. 6. Select one of the following: • On/Off to enable or disable the selected event. • Edit to edit the settings for the selected event.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Color Temp. (color temperature) Color Temp. Customized Description Sets the overall color tone; high values tint the image blue (cool) and low values tint the image red (warm) Color Temp.
Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting in the ECO menu Note: The Noise Reduction setting is not available if you have set the Deinterlacing setting to Off, or selected a digital RGB or interlaced (480i/576i/1080i) input signal.
Setting Options Description Resolution Auto Sets the input signal resolution if not detected automatically using the Auto option Wide Normal Aspect See the list of available aspect ratios Sets the aspect ratio (width-toheight ratio) for the selected input source Tracking Varying levels available Adjusts signal to eliminate vertical stripes in computer images Sync.
Setting Options Description HDMI Video Range Auto Sets the video range to match the setting of the device connected to the HDMI input port Normal Expanded Auto: detects the video range automatically Normal: for images from a device other than a computer; select if the black areas of the image are too bright Expanded: for images from a computer; select if the image is too dark Input Signal Auto Specifies the signal type from input sources connected to computer ports RGB Component Auto: detects si
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. The available settings depend on the currently selected input source.
Setting Options Description Split Screen Screen Size Divides the viewing area horizontally and displays two images side-by-side (press Esc to cancel split screen display) Source Swap Screens Audio Source Align Display the QR Code Gesture Presenter Start/Stop Marker Position Gesture Presenter Adjusts the Gesture Presenter options Start/Stop: starts or stops the Gesture Presenter function Marker Position: sets the marker position to the right or left Gesture Presenter: enables or disables the Gesture
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Power On Link Power Off Link Link Buffer Device Connections: lists the devices connected to the HDMI 1/MHL and HDMI 2 ports HDMI Link: enables or disables the HDMI Link function Power On Link: controls the projector or a linked device • PJ -> Device or Bidirectional: turns on the linked device when the projecto
Setting Options Description Pointer Shape Three shapes available Changes the shape of the remote control pointer feature Remote Receiver Front/Rear Limits reception of remote control signals by the selected receiver; Off turns off all receivers Front Rear Off User Button Power Consumption Info Assigns a menu option to the User button on the remote control for one-touch access Deinterlacing Closed Caption Test Pattern Resolution Multi-Projection Display the QR Code Test Pattern — Displays a tes
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Select various options for the projector's Home screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen Display Background: selects the screen color or logo to display when no signal is received A/V Mute Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and s
Setting Options Description Operation Direct Power On Selects various operation options High Altitude Mode Direct Power On: turns on the projector when you plug it in Auto Source Search High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) Auto Power On Monitor Out Port Date & Time Auto Source Search: automatically detects the image signal being input when the projector is turned on Auto Power On: automatically turns on the projector when it rec
Setting Options Description Multi-Projection Multi-Projection Select various options when projecting from multiple projectors Projector ID Multi-Projection: set to On to match the display quality of multiple projectors Color Mode Color Matching Projector ID: sets the projector to a particular ID number which allows you to use a remote control to individually control projectors RGBCMY Color Mode: adjusts the vividness of image colors for various image types and environments; make sure to select th
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Wireless LAN System Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code IPv6 Net.
Projector Setup Settings - ECO Menu Settings on the ECO menu let you customize projector functions to save power. When you select a power-saving setting, a leaf icon appears next to the menu item.
Setting Options Description Light Optimizer On When Power Consumption is set to Normal and both Auto Iris and Multi Projection are turned off, the lamp brightness is adjusted based on the projected image; you can set this option for each color mode Off Sleep Mode On Automatically places the projector in standby mode after an interval of inactivity Off Sleep Mode Timer 1 to 30 minutes Sets the interval for Sleep Mode Lens Cover Timer On Automatically turns off the projector after 30 minutes if
Parent topic: Adjusting the Menu Settings Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Select Version to display the projector's firmware version. Select Projector Info to display the settings described below. Note: Available settings depend on the current input source.
Information item Description Video Signal Displays the video signal format of the current input source Refresh Rate Displays the refresh rate of the current input source Sync Info Displays information that may be needed by a service technician Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Event ID Displays the Event ID number corresponding to a specific projector problem; see the list of Event
Event ID code Cause and solution 0483 The network software quit unexpectedly. Check the network communication status, then turn the projector off and then on again. 04FE 0484 Communication with computer was disconnected. Restart the network software. 0479 A projector system error has occurred. Turn the projector off and then on again. 04FF 0891 Cannot find an access point with the same SSID. Set your computer, access point, and projector to the same SSID.
You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option.
Related references Available Color Modes Projector Setup Settings - ECO Menu 156
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Related references Projector Light Status Cleaning the Air Filter and Vents Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them. 1. Turn off the projector and unplug the power cord. 2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
1. Slide the air filter cover latch and open the air filter cover. 2. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
3. Place the new air filter in the projector as shown and push gently until it clicks into place. 4. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Related references Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Related references Projector Light Status Projector Information Display - Info Menu Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. 9. Replace the lamp cover and tighten the screw to secure it.
Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Related references Optional Equipment and Replacement Parts Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1.
3. Insert the batteries with the + and – ends facing as shown. 4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Close the lens cover to protect the lens. • Remove any equipment connected to the projector. • Use a carrying case to hand-carry the projector. • When transporting the projector a long distance or as checked luggage, place it in a carrying case. Then pack the case in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solving Network Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
On/Standby light Status light Lamp light Temp light Status and solution Blue Flashing blue Off Off Warming up; wait for an image to appear Blue Off Off Off Standby or sleep mode Flashing blue Off Off Off Preparing for network monitoring Flashing blue Varies Off Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too hot
On/Standby light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem Off • Check to see if the lamp is burned out, broken, or installed incorrectly; reseat or replace the lamp as necessary • Clean or replace the air filter • If operating the projector at high altitude, turn on High Altitude Mode • If the problem persists, unplug the projector and contact Epson for help Flashing blue Varies Flashing orange Off Replace the lamp soon to avoid damage;
Related concepts Air Filter and Vent Maintenance Projector Lamp Maintenance Related references Projector Setup Settings - Extended Menu Where to Get Help Related tasks Turning Off the Projector Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Home button on the projector or the remote control. 3. Press the arrow buttons to select Help. 4. Press Enter. You see the Help menu. 5.
Solutions When Only a Partial Image Appears Solutions When the Image is Not Rectangular Solutions When the Image Contains Noise or Static Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect Solutions to Sound Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens cover is open all the way.
Related references Projector Setup Settings - Extended Menu Image Quality Settings - Image Menu Input Signal Settings - Signal Menu Projector Reset Options - Reset Menu Related tasks Unlocking the Projector's Buttons Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the USB button on the remote control. • Make sure the USB Display software has installed correctly.
• Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary. • Check the connection from the projector to your video sources. • If you are projecting from a laptop computer, make sure it is set up to display on an external monitor. • If necessary, turn the projector and the connected computer or video source off and then on again.
1. Open the System Preferences utility and select Displays, Display, or Color LCD. 2. Click the Arrange or Arrangement tab. 3. Select the Mirror Displays checkbox. Parent topic: Solutions When "No Signal" Message Appears Solutions When No Image Appears on an External Monitor If no image appears on a connected external monitor, try the following solutions: • Make sure a VGA cable is connected to your computer and the projector's Computer1 port.
• Make sure the Resolution setting in the Signal menu is set correctly to for the input signal. • Try adjusting the image position using the Position menu setting. • Press the Aspect button on the remote control to select a different image aspect ratio. • If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button until the projector returns to a full display. • Check the cables connecting the computer or video source to the projector. Try connecting different cables.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.
• Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen. • Position the projector so the keystone adjustment angle is not so wide that it distorts the image. • When using the Screen Fit feature, position the projector at a compatible distance from the screen or adjust the image shape manually.
• Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Color Temp., and/or Color Saturation. • Make sure you selected the correct Input Signal or Video Signal setting on the Signal menu, if available for your image source. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.
• If you are using the USB Display function, turn on the Output audio from the projector setting in the Epson USB Display Settings program on your computer. • If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac supports audio through the HDMI port. If not, you need to connect an audio cable. • If you want to use a connected audio source when the projector is off, set the Standby Mode option to Communication On and make sure the A/V Settings options are set correctly.
• If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receiver setting is turned on in the projector's menu, if available. • The power cord may be defective. Try another power cord. If that doesn't work, disconnect the cord and contact Epson.
Related references Projector Feature Settings - Settings Menu Remote Control Operation Related tasks Replacing the Remote Control Batteries Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control. • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson.
• If you connected a new device or changed any connections, you may need to restart the device. • Connect no more than three devices that support HDMI Link at the same time. • If you have connected a speaker or receiver, set the output to PCM. Parent topic: Solving Projector or Remote Control Operation Problems Solving Network Problems Check the solutions in these sections if you have problems using the projector on a network.
Note: You cannot change the user ID. • You may need to log in to access some options on the Web Control screen. If you see a log in window, enter EPSONWEB as the user ID, and enter the password set in the projector's Network menu as the password. The default password is admin. • To display the Web Remote screen, enter EPSONREMOTE as the user ID and enter the password set in the projector's Network menu as the password. The default password is guest.
Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at epson.com/support (U.S.), epson.ca/support (Canada), or epson.com.jm/support (Caribbean) and select your product for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Technical Specifications These sections list the technical specifications of your projector.
Image size 45 inches (1.14 m) to 260 inches (6.6 m) (in native aspect ratio) Projection distance 59.4 inches (1.51 m) to 572 inches (14.53 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:10 (width-to-height) Focus adjustment Manual Zoom adjustment Manual Zoom ratio 1.0 to 1.
Lamp life Normal Power Consumption mode: Up to about 5000 hours ECO Power Consumption mode: Up to about 10000 hours Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Power consumption Operating: (100 to 120 V) Normal Power Consumption mode: 429 W ECO Power Consumption mode: 340 W Standby: 2.41 W (Communication On), 0.31 W (Communication Off) Power consumption Operating: (220 to 240 V) Normal Power Consumption mode: 405 W ECO Power Consumption mode: 323 W Standby: 2.41 W (Communication On), 0.
Canada ICES-003 Class B CSA C22.2 No. 60950-1 Parent topic: Technical Specifications Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
Display format Refresh rate (in Hz) Resolution (in pixels) TV (NTSC) 60 720 × 480 TV (SECAM) 50 720 × 576 TV (PAL) 50/60 720 × 576 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 UXGA 60 1600 × 1200 WSXGA+ 60 1680 × 1050 SXGA 60 1280 × 960 60 1280 × 1024 SXG
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 VGA 60 640 × 480 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 MHL input signals * Wide resolution only Parent topic: Technical Specifications USB Display System Requirements Your computer system must meet the system requirements here to use the proje
Requirement Windows Mac CPU Intel Core2 Duo or faster (Intel Core i3 or Intel Core2 Duo or faster (Intel Core faster recommended) i5 or faster recommended) Memory 2GB or more (4GB or more recommended) Hard disk space 20MB or more Display Resolution between 640 × 480 and 1920 × 1200, 16-bit color or greater Parent topic: Technical Specifications 197
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Open Source Software License Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants. This may cause the projector case to crack and the projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and could damage the projector. • Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of magnetic fields. • Use the type of power source indicated on the projector.
• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: if it does not operate normally when you follow the operating instructions, or exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been d
Restriction of Use Parent topic: Notices Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
No. 4 Symbol Approved Standards Description ISO7000 Caution No.0434B, To identify general caution when using the product. IEC3864-B3.1 5 6 IEC60417 Caution, hot surface No.5041 To indicate that the marked item can be hot and should not be touched without taking care. IEC60417 Caution, risk of electric shock No.6042 To identify equipment that has risk of electric shock. ISO3864-B3.6 7 8 9 IEC60417 For indoor use only No.
No. 11 12 Symbol Approved Standards Description IEC60417 Positioning of cell No.5002 To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. — Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. 13 14 15 16 17 IEC60417 Protective earth No.
No. Symbol 18 Approved Standards Description ISO 3864 General prohibition To identify actions or operations that are prohibited. 19 ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. 20 — Never look into the optical lens while the projector is on. 21 — To indicate that the marked item don’t place anything on projector. 22 ISO3864 Caution, laser radiation IEC60825-1 To indicate the equipment has a laser radiation part.
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
• iptables-1.4.20 • linux-3.4.49 • patches • udhcp 0.9.8 • wireless_tools 29 • dbus-1.6.18 • EPSON original drivers • Stonestreet One Drivers • mtd-utils-1.5.0 • dibbler-1.0.1 • linux-2.6.32 • u-boot-2001.06 • busybox-1.19.4 • backports-3.10.4-1 • wifi driver The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
• alsa-lib-1.0.27.2 • libdbus-c++-0.9.0 • grencode-3.4.2 • libnl-3.2.24 • libiconv-1.14 The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc.
source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library".
a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5.
and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.
Copyright (C) This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
============ In plain English: 1. We don't promise that this software works. (But if you find any bugs, please let us know!) 2. You can use this software for whatever you want. You don't have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code.
The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable. It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi.
libpng versions 1.2.6, August 15, 2004, through 1.2.49, March 29, 2012, are Copyright (c) 2004, 20062009 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.
For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals: Andreas Dilger Dave Martindale Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc.
zlib This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib". The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of zlib programs • zlib-1.1.4 • zlib-1.2.5 License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows.
aes-src-29-04-09 This projector product includes the open source software program "aes-src-29-04-09" which applies the terms and conditions provided by owner of the copyright to the "aes-src-29-04-09". The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The newlib subdirectory is a collection of software from several sources. Each file may have its own copyright/license that is embedded in the source file. Unless otherwise noted in the body of the source file(s), the following copyright notices will apply to the contents of the newlib subdirectory: (1) Red Hat Incorporated Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved.
The author of this software is David M. Gay. Copyright (c) 1991 by AT&T. Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 080089-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118. Advanced Micro Devices, Inc. 29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W.
Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes. THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. (11) Christopher G. Demetriou Copyright (c) 2001 Christopher G. Demetriou All rights reserved.
So that all may benefit from your experience, please report any problems or suggestions about this software to the SuperH Support Center via e-mail at softwaresupport@superh.com. SuperH, Inc. 405 River Oaks Parkway San Jose CA 95134 USA (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska Högskolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
All rights reserved. Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms. This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. (23) Intel (i960) Copyright (c) 1993 Intel Corporation Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Copyright (c) 1998, M. Warner Losh All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (33) - Daniel Eischen (targets using libc/posix) Copyright (c) 2001 Daniel Eischen . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * * Neither the name of MIPS Technologies Inc.
License terms of conditions of each program which are provided by owner of the copyright to the "MIT License" are as follows. Copyright © 2012 jQuery Foundation and other contributors, http://jquery.com/ Copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers. Copyright © 2009-2012 Petri Lehtinen
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the conditions described in Version 2 of the GNU Public License officially announced by the Free Software Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization) of this software (this software includes alterations, likewise below) without compensation.
License terms of conditions of each program which are provided by owner of the copyright to the "TINET" are as follows. (1) FreeBSD Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
(1) When this software is utilized in the form of source code, the above copyright declaration, these conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged form inside the source code. (2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc.
----------This software may be distributed, used, and modified under the terms of BSD license: Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of the 'incremental' nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
The basic library functions are written in C and are freestanding. Also included in the distribution is a set of C++ wrapper functions, and a just-in-time compiler that can be used to optimize pattern matching. These are both optional features that can be omitted when the library is built. THE BASIC LIBRARY FUNCTIONS ----------Written by: Philip Hazel Email local part: ph10 Email domain: cam.ac.uk University of Cambridge Computing Service, Cambridge, England.
Contributed by: Google Inc. Copyright (c) 2007-2012, Google Inc. All rights reserved. THE "BSD" LICENCE ----------Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
License terms of conditions of each program which are provided by owner of the copyright to the "FastCGI" are as follows. This FastCGI application library source and object code (the "Software") and its documentation (the "Documentation") are copyrighted by Open Market, Inc ("Open Market"). The following terms apply to all files associated with the Software and Documentation unless explicitly disclaimed in individual files.
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org. OpenSSL License Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay license Copyright (c) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL.
available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence, including the GNU Public Licence. iperf This projector product includes the open source software program "iperf" which applies the terms and conditions provided by owner of the copyright to the "iperf". The "iperf" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of iperf programs • iperf-2.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution.
This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least. This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software in commercial and freeware products alike. As a consequence, its main points are that: • We don't promise that this software works.
This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise stated in the file in its original, unmodified form as distributed in the original archive. If you are unsure whether or not a particular file is covered by this license, you must contact us to verify this. The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below. 1.
We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project', `FreeType Engine', `FreeType library', or `FreeType Distribution'. As you have not signed this license, you are not required to accept it. However, as the FreeType Project is copyrighted material, only this license, or another one contracted with the authors, grants you the right to use, distribute, and modify it.
also agree, notwithstanding Section 1.6,that a court, not an arbitrator, may decide if a claim or cause of action is for an IP Claim. 1.2 Binding Arbitration. You and Epson agree that all Disputes shall be resolved by binding arbitration according to this Agreement. ARBITRATION MEANS THAT YOU WAIVE YOUR RIGHT TO A JUDGE OR JURY IN A COURT PROCEEDING AND YOUR GROUNDS FOR APPEAL ARE LIMITED.
1-800-352-5267, and under the rules set forth in this Agreement. All Disputes shall be resolved by a single neutral arbitrator, and both parties shall have a reasonable opportunity to participate in the selection of the arbitrator. The arbitrator is bound by the terms of this Agreement.
any; and (iii) reimburse you for any expenses (including expert witness fees and costs) that your attorney reasonably accrues for investigating, preparing, and pursuing the Dispute in arbitration. Except as agreed upon by you and Epson in writing, the arbitrator shall determine the amount of fees, costs, and expenses to be paid by Epson pursuant to this Section 1.6d). e) Attorney's Fees.
Mac, OS X, and iOS are trademarks of Apple Inc., registered in the U.S. and other countries. AndroidTM and ChromebookTM are trademarks of Google Inc. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices Copyright Notice All rights reserved.
A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law. Parent topic: Copyright Notice Copyright Attribution © 2017 Epson America, Inc.
