Product Information Guide

ManualsBrandsEpson ManualsPrint EngineEpson Epson Stylus Pro 7500 Print Engine

EPSON Stylus Pro 7000 series

8/00 EPSON Stylus Pro 7000 series - 1

Note:

The parallel and USB interfaces cannot be connected at the same

time.

Printer Specifications

Printing

Engine Reliability

Electrical

roll paper cover

paper hammock

control

panel

lower

cover

paper set lever

parallel interface connector

optional interface

shield plate

USB interface

connector

AC inlet

ink cartridge

compartment

paper set lever

Note:

The stand is optional.

Printing method On-demand ink jet

Nozzle

configuration

Black: 64 nozzles

Color: 64 nozzles for each color: (cyan,

magenta, yellow, light cyan, light magenta)

Resolution Maximum 1440 dpi

720 dpi

Maximum

printable width

23.76 inches on 24-inch paper

Print direction Bidirectional or unidirectional

(user-selectable)

Control code ESC/P

Raster

Line spacing 1/6 inch (default), programmable in

1/360-inch increments

Paper feed speed 200 ± 10 milliseconds per 1/6-inch line

RAM 10MB

Total print

volume

20,000 A1 images, 30% coverage

(or 5 years)

Print head life Two billion dots per nozzle

Periodic

maintenance

Waste ink system requires replacement after

approximately 12,000 sheets under normal

usage (parts and labor not covered under

warranty)

Cutter blade life Approximately 2000 A1 sheets (EPSON

media up to 4.33 mil thick)

Specification 120V Model 220

−

240V Model

Input voltage range 90 to 132V 198 to 264V

Rated frequency range 50 to 60 Hz

Input frequency range 49 to 61 Hz

Rated current 1.0A 0.5A

Power consumption Approx. 100W (ISO/IEC 10561 Letter Pattern)

15W or less in standby mode

Summary of content (12 pages)

PAGE 1
EPSON Stylus Pro 7000 series - roll paper cover Printer Specifications paper set lever ink cartridge compartment Printing Printing method On-demand ink jet control panel lower cover paper hammock Note: Nozzle configuration Black: 64 nozzles Color: 64 nozzles for each color: (cyan, magenta, yellow, light cyan, light magenta) Resolution Maximum 1440 dpi × 720 dpi Maximum printable width 23.
PAGE 2
EPSON Stylus Pro 7000 series Paper Cut sheet paper specifications Size Dimensions in inches Dimensions in millimeters Thickness Super A1 24 × 36 610 × 914 US D 22 × 34 559 × 864 3.15 to 19.7 mil (0.08 to 0.5 mm) A1 23.4 × 33 594 × 841 B2 20.25 × 28.75 515 × 728 A2 16.5 × 23.4 420 × 594 Super A3/B* 13 × 19 329 × 483 US C 17 × 22 432 × 559 B3 14.3 × 20.25 364 × 515 US B (ledger)* 11 × 17 279 × 432 A3* 11.7 × 16.5 297 × 420 B4* 9.8 × 13.9 250 × 353 A4* 8.27 × 11.
PAGE 3
EPSON Stylus Pro 7000 series Ink Cartridges Print yield Interfaces Approximately 28 pages/A1 (720 dpi, 40% duty) Approximately 3,800 pages/A4 (360 dpi, 5% duty); print yield may vary, depending on how often you run cleaning cycles and how much you use the printer; yield of the initial cartridge set is reduced because of ink charging Parallel interface The built-in parallel interface supports compatibility and ECP modes.
PAGE 4
EPSON Stylus Pro 7000 series ECP mode Drivers Transmission mode IEEE-1284 ECP mode Adaptable connector 57-30360 Amphenol connector or equivalent Macintosh® System 8.5.1 or later, Windows® 95, Windows 98, Windows 2000, and Windows NT 4.0. Raster drivers are standard. For Adobe® PostScript ® support, use the optional EPSON RS-5100 Fiery® X2 Printing System or a third-party software solution.
PAGE 5
EPSON Stylus Pro 7000 series You can also use EPSON Photo Quality Ink Jet Paper, Photo Paper, and Photo Quality Glossy Film in the EPSON Stylus Pro 7000 printer. Consumables and Accessories Ink Cartridges EPSON Stylus Pro 7500 media Use these EPSON 110 ml ink cartridges before the expiration date on the package.
PAGE 6
EPSON Stylus Pro 7000 series Control Panel Lights and Messages Control Panel Normal printer operation Message/Light Explanation READY/ Operate light on Printer is ready to print. PRINTING/ Operate light Printer is receiving data. flashing INK DRY MIN/ Pause light flashing Printer is paused to let ink dry. Wait for the number of minutes shown. INK CHARGING %/Operate and Pause lights flashing Printer is charging the ink delivery system. Do not interrupt this process.
PAGE 7
EPSON Stylus Pro 7000 series Message/Light Explanation Response PAPER NOT STRAIGHT/ Paper Out light Paper slipped and fed into the printer at an angle. Reload paper, making sure the edges are straight and aligned with both rows of holes. flashing PAPER OUT/ Paper Out light No paper is loaded. Load paper. Paper ran out. Remove any printouts or paper remaining in the printer and load more paper. If the message appears during a print job, reset the printer by pressing the Pause button for 3 seconds.
PAGE 8
EPSON Stylus Pro 7000 series 4. Press the Enter button. The status check prints.
PAGE 9
EPSON Stylus Pro 7000 series If you’re using pigment ink (EPSON Stylus Pro 7500), shake the cartridge gently before installing it. 3. Examine the nozzle check pattern. It should look something like this: Each line should be complete, with no gaps in the dot pattern. If dots are missing, as shown below, you need to run a cleaning cycle. See the following section for instructions. 5. Hold the ink cartridge with the arrow mark face up and pointing to the rear of the printer.
PAGE 10
EPSON Stylus Pro 7000 series 3. When the Pause light goes off, print a document or run a nozzle check to confirm that the head is clean. EPSON Stylus Pro 7000 Alignment Patterns 1 You may need to run the cleaning cycle several times to get a clean nozzle check pattern. If the lines on the pattern still appear broken after several cleaning cycles, contact EPSON for assistance. 2 3 Always run a test print or nozzle check between cleaning cycles. Otherwise, cleaning will not be effective.
PAGE 11
EPSON Stylus Pro 7000 series 7. Check the control panel display. 6. Select the row you chose in step 5 for each pattern (for example line 8), then click Finish. ❏ For the EPSON Stylus Pro 7000, it shows #1 = 4, indicating that row 4 is selected for pattern #1. If you can’t make a consistent choice for the patterns as you look across the width of the paper, choose the average or most frequent number. Then click the Realignment button and repeat from step 5.
PAGE 12
EPSON Stylus Pro 7000 series 6. If you’re using the stand, remove the wing screws and washers from the left and right sides, and keep them in a safe place. Moving the Printer on the Stand When you want to transport the printer a short distance, such as within the same building or facility, you can roll the printer on its casters. Caution: Do not roll the printer on angled or uneven surfaces. 1.