Home Cinema 660/760HD/1060 User's Guide
Contents Home Cinema 660/760HD/1060 User's Guide............................................................................................ 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents...........................................................
Connecting to a Component Video Source ............................................................................... Connecting to a Composite Video Source ................................................................................ Connecting to a Video Source for Sound .................................................................................. Connecting to External USB Devices ............................................................................................ USB Device Projection..
Correcting Image Shape with Quick Corner .................................................................................. 78 Resizing the Image with the Zoom Ring ............................................................................................. 80 Focusing the Image Using the Focus Ring......................................................................................... 80 Remote Control Operation .............................................................................................
Locking the Projector's Buttons ................................................................................................... Unlocking the Projector's Buttons ........................................................................................... Installing a Security Cable ........................................................................................................... Projector Identification System for Multiple Projector Control........................................................
Resetting the Lamp Timer....................................................................................................... 156 Replacing the Remote Control Batteries ..................................................................................... 157 Transporting the Projector................................................................................................................ 159 Solving Problems ...........................................................................................
Projector Dimension Specifications.................................................................................................. Projector Electrical Specifications .................................................................................................... Projector Environmental Specifications............................................................................................ Projector Safety and Approvals Specifications..................................................................
Home Cinema 660/760HD/1060 User's Guide Welcome to the Home Cinema 660/760HD/1060 User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• HDMI port for computer or video device connection (Home Cinema 660/760HD) Easy-to-use setup and operation features • Epson's quick-connect on-screen QR code feature for easy wireless setup • Low total cost of ownership with longer lamp life • Automatic vertical keystone correction and innovative horizontal keystone correction slider for flexible projector placement • Epson's Instant Off and Direct Power On features for quick setup and shut down • Built-in closed captioning decoder (composite NTSC input si
Make sure your projector boxes included all of these parts: 1 Projector 2 Remote control 3 Remote control batteries (two AA alkaline) 4 Power cord 5 Projector documentation CD Parent topic: Projector Features Related concepts Projector Connections Additional Components Depending on how you plan to use the projector, you may need to obtain additional components.
Unless listed as available from Epson in this table, see your local computer or electronics dealer for purchase information. Signal or connection type Additional component necessary Composite video RCA-style video or A/V cable Component video D-sub, 15-pin, component-to-VGA video cable or adapter Available for purchase from Epson or an authorized Epson reseller. HDMI Compatible HDMI cable Available for purchase from Epson or an authorized Epson reseller.
Projector software Manual Description Epson Projector Management (Windows only) Epson Projector Management Guide Lets you monitor and control your projector through the network. Epson iProjection (Windows/Mac) Epson iProjection Operation Guide You can download the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.
Option or part Part number Genuine Epson replacement lamp (ELPLP96) V13H010L96 Replacement air filter (ELPAF32) V13H134A32 Wireless LAN module (ELPAP10; Home Cinema 660/760HD) V12H731P02 Universal projector mount (ELPMBPJG) V12H808001 Soft carrying case (ELPKS69) V12H001K69 Accolade Duet portable projector screen ELPSC80 HDMI audio video cable 3 feet (0.9 m) length AV22300-03 HDMI audio video cable 6 feet (1.
• Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • Built-in help system Press the Home button on the remote control or projector, select Help, and press Enter to get quick solutions to common problems. • epson.com/support (U.S.) or epson.
Projector Parts - Front/Top 1 Exhaust vent 2 A/V Mute slide lever 3 Foot release lever 4 Lens cover 5 Front adjustable foot 6 Lens 7 Remote control receiver 8 Horizontal keystone slider 9 Air filter/intake vent 10 Air filter cover 11 Kensington security lock slot 12 Control panel 13 Zoom ring (Home Cinema 760HD/1060) 17
14 Focus ring 15 Lamp cover Parent topic: Projector Part Locations Projector Parts - Rear Home Cinema 660/760HD Home Cinema 1060 1 AC input 2 Audio ports 3 Video port 4 Remote receiver 18
5 Speaker 6 HDMI port (Home Cinema 660/760HD); HDMI1 and HDMI2/MHL ports (Home Cinema 1060) 7 Computer port 8 USB-B port 9 USB-A port Parent topic: Projector Part Locations Projector Parts - Base 1 Ceiling mount holes (3) 2 Security cable attachment point 19
3 Rear feet 4 Front adjustable foot Parent topic: Projector Part Locations Projector Parts - Control Panel Home Cinema 660 20
Home Cinema 760HD Home Cinema 1060 1 Source Search button (searches for connected video sources) 2 Enter button (selects options) 21
3 Vertical keystone adjustment buttons (displays the adjustment screen and adjusts screen shape) and arrow buttons 4 Esc button (cancels/exits functions) 5 Volume buttons (adjust speaker volume; Home Cinema 760HD/1060), horizontal keystone adjustment buttons, and arrow buttons 6 Menu button (accesses projector menu system) 7 Home button (displays Home screen) 8 Power button 9 Status lights Parent topic: Projector Part Locations Related references Projector Light Status Related tasks Using the
Projector Parts - Remote Control 1 Power button 23
2 Computer button (cycles through connected computer sources) 3 HDMI/Video button (cycles through connected HDMI/video sources) 4 Numeric buttons (enter numbers) 5 Auto button (automatically adjusts position, tracking, and sync settings when projecting from a computer using a VGA cable) 6 Aspect button (selects the image aspect ratio) 7 Num button (when held down, switches numeric buttons to number function) 8 Menu button (accesses projector menu system) 9 Arrow buttons (move through on-scree
Parent topic: Projector Part Locations 25
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Front Rear Front Ceiling 27
Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image. (Conversion figures may have been rounded up or down.) You can also use the Projection Distance Calculator here (U.S.), here (Canada), or here (Caribbean).
4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 80 inches 93 to 126 inches –5.2 inches (–13 cm) (237 to 321 cm) 100 inches 117 to 158 inches –6.5 inches (–17 cm) (297 to 401 cm) 150 inches 176 to 237 inches –9.8 inches (–25 cm) (446 to 603 cm) Home Cinema 760HD 16:10 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 50 inches 55 to 66 inches –2.
Home Cinema 1060 16:9 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 50 inches 44 to 54 inches –1.6 inch (–4 cm) (113 to 136 cm) 80 inches 71 to 86 inches –2.6 inches (–7 cm) (181 to 219 cm) 100 inches 89 to 108 inches –3.3 inches (–8 cm) (227 to 275 cm) 150 inches 135 to 163 inches –4.
Connecting to a Computer for VGA Video Connecting to a Computer for HDMI Video and Audio Connecting to a Computer for USB Mouse Control Connecting to a Computer for Sound Parent topic: Projector Connections Connecting to a Computer for USB Video and Audio If your computer meets the system requirements, you can send video and audio output to the projector through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a USB cable.
Home Cinema 1060 3. Connect the other end to any available USB port on your computer. 4. Do one of the following: • Windows 10/Windows 8.x: Click EPSON_PJ_UD when it appears on the desktop, then select Run EMP_UDSE.EXE in the dialog box that appears to install the Epson USB Display software. • Windows 7/Windows Vista: Select Run EMP_UDSE.EXE in the dialog box that appears to install the Epson USB Display software. • Mac: The USB Display setup folder appears on your screen.
3. Connect the other end to a Computer port on the projector. Home Cinema 660/760HD Home Cinema 1060 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port. 1. Connect the HDMI cable to your computer's HDMI output port. 2. Connect the other end to the projector's HDMI port. Home Cinema 660/760HD Home Cinema 1060 Note: The projector converts the digital audio signal sent from your computer into a mono analog signal for the internal speaker.
Connecting to a Computer for USB Mouse Control If you connected your computer to a Computer, USB-B, or HDMI port on the projector, you can set up the remote control to act as a wireless mouse. This lets you control projection at a distance from your computer. To do this, connect the projector to your computer using a USB cable, if it is not connected already. 1. Connect the USB cable to your projector's USB-B port. Home Cinema 660/760HD Home Cinema 1060 2.
Related tasks Using the Remote Control as a Wireless Mouse Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it using the projector's USB-B or HDMI port, you can still play sound through the projector's speaker system. Connect an optional stereo mini-jack adapter cable (with one 3.5 mm mini-plug and two RCA plugs). 1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port. 2.
Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector. Connecting to an HDMI Video Source Connecting to an MHL-Compatible Device Connecting to a Component Video Source Connecting to a Composite Video Source Connecting to a Video Source for Sound Parent topic: Projector Connections Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Home Cinema 1060 Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker. Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher. See your game console documentation for instructions.
3. Connect the other end of the cable to the projector's HDMI2/MHL port. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker. Parent topic: Connecting to Video Sources Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable.
Home Cinema 1060 3. Tighten the screws on the VGA connector. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Signal menu. Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signal Menu Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1.
2. Connect the other end to the projector's Video port. Home Cinema 660/760HD Home Cinema 1060 Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher. See your game console documentation for instructions.
1. Connect the audio cable to your video source's audio-out ports. 2. Connect the other end of the cable to the projector's Audio port or ports. Home Cinema 660/760HD Home Cinema 1060 Note: To add additional sound, connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI connection provides the best image quality, if available).
USB Device Projection Connecting a USB Device or Camera to the Projector Selecting the Connected USB Source Disconnecting a USB Device or Camera From the Projector Parent topic: Projector Connections Related topics Projecting a PC Free Presentation USB Device Projection You can project images and other content without using a computer or video device by connecting any of these devices to your projector: • USB flash drive • Digital camera or smartphone • USB hard drive • Multimedia storage viewer Note: Digit
2. Connect the USB cable (or USB flash drive) to the projector's USB-A port. Home Cinema 660/760HD Home Cinema 1060 Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly. 3. Connect the other end of the cable (if applicable) to your device. Parent topic: Connecting to External USB Devices Selecting the Connected USB Source You can switch the projector's display to the source you connected to the USB-A port. 1.
2. Press the USB button on the remote control. Parent topic: Connecting to External USB Devices Disconnecting a USB Device or Camera From the Projector When you finish presenting with a connected USB device or camera, you must prepare to disconnect the device from the projector. 1. If the device has a power button, turn off and unplug the device. 2. Disconnect the USB device or camera from the projector.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Opening the Lens Cover To open the projector's lens cover, slide the A/V Mute slide lever until it clicks into the open position.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Wireless Network Projection You can project over a wireless network. To do this, you must set up your projector and computer for wireless projection.
Note: The wireless LAN module is not included with your projector and is optional. Note: You do not need the wireless LAN module for the Home Cinema 1060 since the wireless functionality is built-in. 1. Turn off the projector and unplug the power cord. 2. Insert the wireless LAN module into the USB-A port. 3. Plug in and turn on the projector. The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter.
4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Do one of the following: • Press the LAN button on the remote control. • Select Display the QR Code in the projector's Network menu.
Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8. Start Epson iProjection on your mobile device. 9. Use the QR code reader feature to read the QR code and connect your device to the projector. Visit epson.com/iprojection (U.S.) or epson.ca/iprojection (Canada) for instructions.
Home Cinema 1060 You see a projected message that the network information update is complete. 5. Remove the USB key. 6. Reinsert the wireless LAN module into the projector (Home Cinema 660/760HD). 7. Insert the USB key into a USB port on your computer. Note: In Windows Vista, if you see the AutoPlay window, select Run MPPLaunch.exe, then select Allow on the next screen. 8. Follow the on-screen instructions to install the Epson iProjection (Windows/Mac) software.
Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Make sure the Wireless Mode setting is set to Wireless LAN On. 5. Select Network Configuration and press Enter.
6. Select the Basic menu and press Enter. 7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in the Epson Web Control. (Default user name is EPSONREMOTE; default password is guest.
• Display LAN Info lets you select how the projector displays network information. You can select an option to display a QR code that lets you quickly connect your iOS or Android devices using the Epson iProjection app. Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press Enter to select them. 8. Select the Wireless LAN menu and press Enter. 9.
Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you connect to multiple smartphones, tablets, or computers directly Advanced: lets you connect to multiple smartphones, tablets, or computers via a wireless network access point Search Access Point To Search View Search for available wireless network access points in Advanced connection mode SSID Up 32 alphanumeric characters Sets the SSID (network name) of t
Setting Options Description SSID Display On Selects whether to display the SSID on the network standby screen Off IP Address Display On Selects whether to display the IP address on the network standby screen Off IPv6 Settings IPv6 Auto Configuration Selects the IPv6 settings when you connect the projector to the network using IPv6 Use Temporary Address Parent topic: Selecting Wireless Network Settings Manually Selecting Wireless Network Settings in Windows Before connecting to the projector, se
Setting Up Wireless Network Security You can set up security for your projector to use on the wireless network. Set up one of the following security options to match the settings used on your network: • WPA/WPA2-PSK security (Advanced connection mode) • WPA2-PSK security (Advanced and Quick connection mode) Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3.
Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Notifications menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server setting.
10. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
4. Select the Notifications menu and press Enter. 5. Turn on the SNMP setting. 6. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7.
Note: The web setup and control features support Microsoft Internet Explorer 9.0 or later, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser. Note: If you set Standby Mode to Communication On in the ECO menu, you can use a web browser to select settings and control projection even if the projector is in standby mode. 1. Make sure the projector is turned on. 2.
4. To select projector menu settings, select Advanced to bring up a list of options. Note: You may need to log in to access some of the options on the Web Control screen. If you see a log in window, enter your user name and password. (The default user name is EPSONWEB and the default password is admin.) 5. To control projection remotely, select the Basic Control option from the Web Control screen. Note: If you see a log in window, enter your user name and password.
2 Selects an HDMI port source 3 Selects the USB Display source 4 Selects the USB device source 5 A/V Mute button control 6 Freeze button control 7 Page Up and Page Down button controls 8 Displays a QR code 9 Volume button controls 10 Selects the network source 11 Selects the Computer port source 12 Selects a Video port source 13 Searches for connected sources 6. Select the icon corresponding to the projector function you want to control.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the remote control to turn on the projector. The projector beeps and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue.
• If the Home screen is displayed, select the source you want to project. Using the Home Screen Parent topic: Using Basic Projector Features Related tasks Selecting an Image Source Using the Home Screen You can select input sources and other frequently used options from the Home screen. 1. To display the Home screen, do one of the following: • Press the Home button on the control panel or remote control. • Turn on the projector with the Home Screen Auto Disp setting enabled.
3 Display the Help screen 4 Display the projector's menus 5 Select customizable menu options 6 Depending on the projector, select to project two images from different image sources simultaneously or change the Power Consumption setting 7 Correct the image shape Note: Your Home screen may look different from the illustration shown here. You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3.
The projector displays a shutdown confirmation screen. 2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). 3. To transport or store the projector, make sure Status light is off, then unplug the power cord.
4. Close the projector's lens cover. Parent topic: Using Basic Projector Features Related references Projector Light Status Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the horizontal keystone slider on the projector to correct the image shape. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button). 2.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen. 3. Press a keystone button on the projector's control panel to adjust the image shape.
Home Cinema 660 Home Cinema 760HD/1060 Note: The horizontal keystone adjustment buttons are labeled Wide and Tele on the Home Cinema 660. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the H/V-Keystone settings in the projector menus.
Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the Quick Corner setting to correct the image shape. 1. Turn on the projector and display an image.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: 6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter.
7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image. 2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring You can correct the focus using the focus ring. 1. Turn on the projector and display an image.
Home Cinema 760HD/1060 Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
1 30° 2 19.7 feet (6 m) 3 15° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
4. Use the following buttons on the remote control to control your presentation: • To move through slides or pages, press the up or down Page buttons. • To move the cursor on the screen, use the arrow buttons. • To left-click, press the button once (press it twice to double-click). • To right-click, press the Esc button. • To drag-and-drop, hold the at the destination.
1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen. Parent topic: Remote Control Operation Related references Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
3. Do one of the following: • Press the Source Search button on the projector or remote control until you see the image from the source you want. • Press the button for the source you want on the remote control.
• Press the Home button on the remote control or projector and select your image source. Note: Your Home screen may look different from the illustration shown here. Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen.
Changing the Projection Mode Using the Remote Control You can change the projection mode to flip the image over top-to-bottom. 1. Turn on the projector and display an image. 2. Hold down the A/V Mute button on the remote control for five seconds. The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for five seconds again.
3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio.
2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3. To cycle through the available aspect ratios for your input signal, press the Aspect button repeatedly. Note: If you are projecting from a computer and parts of the image are cut off, set the Resolution setting to Wide or Normal in the Signal menu.
Aspect ratio setting Description 16:9 Converts the aspect ratio of the image to 16:9. (Home Cinema 760HD) Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. Native Displays images as is (aspect ratio and resolution are maintained).
Parent topic: Using Basic Projector Features Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button. 3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment.
Controlling the Volume with the Volume Buttons You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio. You can also use the volume buttons on the projector's control panel (Home Cinema 760HD/1060). The volume buttons control the projector’s internal speaker system. You must adjust the volume separately for each connected input source. 1. Turn on the projector and start a presentation that includes audio. 2.
File type and extension Details Image (.jpg) Make sure the file is not: • CMYK format • Progressive format • Highly compressed • Above 8192 × 8192 resolution Image (.bmp) Make sure the file resolution is not above 1280 × 800 Image (.gif ) Make sure the file is not: • Above 1280 × 800 resolution • Animated • Interlaced Image (.png) Make sure the file resolution is not above 1280 × 800 Motion JPEG movie (.avi) Supports only AVI 1.
The PC Free screen appears. 2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter. (You can also press the Page up or down buttons on the remote control.) 3.
4. While projecting, use the following commands to control the display as necessary: • To rotate a displayed image, press the up or down arrow button. • To move to the next or previous image, press the left or right arrow button. 5. To stop the display, follow the on-screen instructions or press the Esc button.
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter. (You can also press the Page up or down buttons on the remote control.) 3.
Setting Options Description Display Order Name Order Displays files in name order Date Order Displays files in date order In Ascending Sorts files in first-to-last order In Descending Sorts files in last-to-first order On Displays a slide show continuously Off Displays a slide show one time through Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically; high resolution i
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
Note: You can also stop projection using the A/V Mute slide lever on the projector. Parent topic: Adjusting Projector Features Related references Projector Setup Settings - ECO Menu Related tasks Saving a User's Logo Image to Display Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1.
Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into.
Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings. • Button lock security to block operation of the projector using the buttons on the control panel. • Security cabling to physically cable the projector in place.
1. Hold down the Freeze button on the remote control for about five seconds or until you see this menu. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Press and hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again. You see the message "Password accepted.
Parent topic: Password Security Types Related tasks Selecting Password Security Types Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for about five seconds or until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On, press Enter again, and press Esc. 2.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector. You must enter the correct password to use the projector. 1. Press and hold down the Num button on the remote control while you enter the password using the numeric buttons. Note: The default password is 0000. The password screen closes.
2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password three times in succession, you see a message telling you that the projector is locked. After the message is displayed for 5 minutes, the projector enters standby mode. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to enter the password.
2. Press the Menu button, select the Extended menu, and press Enter. 3. Select the User's Logo setting and press Enter. You see a prompt asking if you want to use the displayed image as a user's logo. 4. Select Yes and press Enter. You see a selection box overlaying your image. 5. Use the arrow buttons on the remote control to surround the image area you want to use as the User's Logo and press Enter. You see a prompt asking if you want to select this image area. 6. Select Yes and press Enter.
You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12. Select when you want to display the User's Logo screen: • To display it whenever there is no input signal, select Display Background and set it to Logo.
2. Select the Settings menu and press Enter. 3. Select Lock Setting and press Enter. 4. Select the Control Panel Lock setting and press Enter. 5. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 6. Select Yes and press Enter.
• Use the security slot on the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture. Note: Do not pass drop-prevention cables through the security cable attachment point when mounting the projector on a wall or ceiling.
2. Select the Extended menu and press Enter. 3. Select Projector ID and press Enter. 4. Press the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter. Repeat these steps for all the other projectors you want to operate from one remote control. Note: If you don't know the projector's ID, aim the remote control at the projector and press the ID button to temporarily display the projector's ID on the screen.
2. Make sure you know the projector's ID number as set in the Extended menu Projector ID setting. Note: If you have forgotten the projector's ID, aim the remote control at the projector and press the ID button to temporarily display the projector's ID on the screen. If you turn off the Projector ID setting, the remote control will operate the projector regardless of the ID selected on the remote. 3. Aim the remote control at that projector. 4.
4. Press the Menu button, select the Image menu, and press Enter. 5. Select settings as necessary. 6. Set the remote control ID to match the next projector, then select Image menu adjustments as necessary to match the projectors' displays. Note: The brightness and tint may not match exactly even after adjustments. If brightness and tint differences become more noticeable over time, repeat the adjustments.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other (Home Cinema 760HD/1060). You can control the split screen feature using the remote control or the projector menus. Note: You cannot use split screen with certain input source combinations.
1. Press the Split button on the remote control. The currently selected input source moves to the left side of the screen. 2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter, select the input source, select Execute, and press Enter. (You can also change image sources, if necessary.) 4. To switch the images, select the Swap Screens setting and press Enter. 5.
6. To choose the audio you want to hear, select the Audio Source setting, press Enter, select an audio option, press Enter, and press Menu to exit. 7. To exit the split screen feature, press the Split or Esc button. Parent topic: Adjusting Projector Features Copying Menu Settings Between Projectors After you select menu settings for your projector, you can transfer them to another projector of the same model.
2. Insert the flash drive into the USB-A port. Home Cinema 660/760HD Home Cinema 1060 Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly.
3. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When all of the projector lights turn on, release the Esc button. The lights flash to indicate that settings are transferring to the flash drive. When the lights stop flashing, the power light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5.
Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have to repeat your adjustments. 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Insert the flash drive into the USB-A port. Home Cinema 660/760HD Home Cinema 1060 Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly.
3. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When all of the projector lights turn on, release the Menu button. The lights flash to indicate that settings are transferring to the projector. When the lights stop flashing, the power light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5.
• Windows 10 • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.x • macOS 10.12.x 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's USB-B port. Home Cinema 660/760HD Home Cinema 1060 3. Connect the other end to any available USB port on your computer.
4. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When all of the projector lights turn on, release the Esc button. The projector shows up as a removable disk on your computer. 6. Open the removable disk and copy the pjconfdata.bin file to your computer. 7. Once the file has copied, do one of the following: • Windows:Open the My Computer, Computer, Windows Explorer, or File Explorer utility.
• Windows 7 • Windows 8.x • Windows 10 • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.x • macOS 10.12.x Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have to repeat your adjustments. 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's USB-B port.
Home Cinema 1060 3. Connect the other end to any available USB port on your computer. 4. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When all of the projector lights turn on, release the Menu button. The projector shows up as a removable disk on your computer.
6. Copy the pjconfdata.bin file from your computer to the removable disk. Note: Do not copy any other files to the removable disk. 7. Once the file has copied, do one of the following: • Windows:Open the My Computer, Computer, Windows Explorer, or File Explorer utility. Right-click the name of your projector (listed as a removable disk) and select Eject. • Mac: Drag the removable disk icon for your projector from the desktop into the trash.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
1. Press the Menu button on the control panel or remote control. You see the menu screen displaying the Image menu settings.
2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
Setting Options Description Color Mode See the list of available Color Modes Adjusts the vividness of image colors for various image types and environments Brightness Varying levels available Lightens or darkens the overall image Contrast Varying levels available Adjusts the difference between light and dark areas of the image Color Saturation Varying levels available Adjusts the intensity of the image colors Tint Varying levels available Adjusts the balance of green to magenta tones in the
Setting Options Description Advanced Deinterlacing Sets whether to convert interlaced to progressive signals for certain video image types Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Auto Iris Off Normal High Speed Adjusts the projected luminance based on the image brightness when the Dynamic or Cinema Color Modes are selected; High Speed sets faster luminance correction for fast-moving images Note: The Brightness setting do
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source. Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Sync.
Setting Options Description Input Signal Auto Specifies the signal type from input sources connected to computer ports RGB Component Auto: detects signals automatically RGB: corrects color for computer/RGB video inputs Component: corrects color for component video inputs Video Signal Auto Various video standards Specifies the signal type from the input sources connected to the video ports Auto: detects signals automatically Parent topic: Adjusting the Menu Settings Projector Feature Settings - S
Setting Options Description Keystone H/V Keystone Adjusts image shape to rectangular (horizontally and vertically) Quick Corner H/V Keystone: lets you manually correct horizontal and vertical sides; turn on or off Auto VKeystone and the H-Keystone Adjuster setting Quick Corner: select to correct image shape and alignment using an on-screen display Split Screen Screen Size (Home Cinema 760HD/1060) Source Swap Screens Divides the viewing area horizontally and displays two images side-by-side (press
Setting Options Description Remote Receiver Front/Rear Limits reception of remote control signals by the selected receiver; Off turns off all receivers Front Rear Off User Button Power Consumption Info Assigns a menu option to the User button on the remote control for one-touch access Deinterlacing Closed Caption Test Pattern Resolution Display the QR Code Test Pattern — Displays a test pattern to assist in focusing and zooming the image and correcting image shape (press Esc to cancel pattern dis
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Select various options for the projector's Home screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen Display Background: selects the screen color or logo to display when no signal is received A/V Mute Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and s
Setting Options Description Operation Direct Power On Selects various operation options High Altitude Mode Direct Power On: turns on the projector when you plug it in Auto Source Search High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) Auto Power On HDMI EQ Setting Auto Source Search: automatically detects the image signal being input when the projector is turned on Auto Power On: automatically turns on the projector when it receives an imag
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net.
Projector Setup Settings - ECO Menu Settings on the ECO menu let you customize projector functions to save power. When you select a power-saving setting, a leaf icon appears next to the menu item.
Setting Options Description Sleep Mode Timer 1 to 30 minutes Sets the interval for Sleep Mode Lens Cover Timer On Automatically turns off the projector after 30 minutes if the lens cover is closed Off A/V Mute Timer On Automatically turns off the projector after 30 minutes if A/V Mute is enabled Off Standby Mode Communication On Communication Off ECO Display On Communication On indicates that the projector can be monitored and controlled over a network when the projector is in standby mode D
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Select Version to display the projector's firmware version. Select Projector Info to display the settings described below. Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Information item Description Refresh Rate Displays the refresh rate of the current input source Sync Info Displays information that may be needed by a service technician Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Event ID Displays the Event ID number corresponding to a specific projector problem; see the list of Event ID codes Event ID Code List Parent topic: Adjusting the Menu Settings Eve
Event ID code Cause and solution 0479 A projector system error has occurred. Turn the projector off and then on again. 04FF 0891 Cannot find an access point with the same SSID. Set your computer, access point, and projector to the same SSID. 0892 The WPA/WPA2 authentication type does not match. Make sure the wireless network security settings are correct. 0893 The TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct.
You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Related references Projector Light Status Cleaning the Air Filter and Vents Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them. 1. Turn off the projector and unplug the power cord. 2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). 3. If dust is difficult to remove or the air filter is damaged, replace the air filter.
3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Related references Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Parent topic: Projector Maintenance Related references Projector Light Status Projector Information Display - Info Menu Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Grasp the raised section of the lamp and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp's usage. Parent topic: Projector Lamp Maintenance Related references Optional Equipment and Replacement Parts Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1.
6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover as shown. 2. Remove the old batteries.
3. Insert the batteries with the + and – ends facing as shown. 4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Close the lens cover to protect the lens. • Remove any equipment connected to the projector. • Use a carrying case to hand-carry the projector. • When transporting the projector a long distance or as checked luggage, place it in a carrying case. Then pack the case in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solving Network Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp light Temp light Status and solution Flashing blue Light status varies Light status varies Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too hot Off Flashing blue Off Orange Projector has overheated and turned off; leave it turned off to cool down for about five minutes, then do the following:
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Off Lamp or lamp cover has a problem • Check to see if the lamp is burned out, broken, or installed incorrectly; reseat or replace the lamp as necessary • Clean or replace the air filter • If operating the projector at high altitude, turn on High Altitude Mode • If the problem persists, unplug the projector and contact Epson for help • Check that the lamp cover is installed correctly Flashing blue Light st
Wireless LAN status (Home Cinema 1060) Wireless LAN light Status and solution Blue Wireless LAN is available Flashing blue quickly Connecting to a device Flashing blue slowly An error has occurred; turn off the projector, then turn it back on Off Wireless LAN is not available; make sure the wireless LAN settings are correct Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help.
7. When you are finished, do one of the following: • To select another problem to solve, press Esc. • To exit the help system, press Home. Parent topic: Solving Problems Solving Image or Sound Problems Check the solutions in these sections if you have any problems with projected images or sound.
• Check the Display setting to make sure Messages is set to On. • If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons. • If the projector does not respond when you press buttons on the remote control, make sure the remote receivers are turned on. • For images projected with Windows Media Center, reduce the screen size from full screen mode. • For images projected from applications using Windows DirectX, turn off DirectX functions.
• If you are projecting using the 1080p video format and change the computer resolution during projection, the video quality and performance may decline. • Make sure you are using the most recent version of the USB Display software. You can download the latest version from the Epson web site. Go to epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.
1. Hold down the laptop's Fn key and press the key labeled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. To display on both the laptop's monitor and the projector, try pressing the same keys again. Note: On Windows 7 or later, hold down the Windows key and press P at the same time, then click Duplicate. 2.
Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal. • Make sure the Resolution setting in the Signal menu is set correctly to for the input signal. • Try adjusting the image position using the Position menu setting.
• Adjust the Quick Corner setting to correct the image shape. Parent topic: Solving Image or Sound Problems Related concepts Image Shape Related references Projector Feature Settings - Settings Menu Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector.
Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen.
Solutions When the Image Brightness or Colors are Incorrect If the projected image is too dark or light, or the colors are incorrect, try the following solutions: • Press the Color Mode button on the remote control to try different color modes for the image and environment. • Check your video source settings. • Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Color Temp., and/or Color Saturation.
• Check the audio cable connections between the projector and your video source. • If you do not hear sound from an HDMI source, set the connected device to PCM output. • Make sure any connected audio cables are labeled "No Resistance". • If you are using the USB Display function, turn on the Output audio from the projector setting in the Epson USB Display Settings program on your computer.
• If the projector's lamp shuts off, the Status light is flashing blue, and the Temp light is orange, the projector has overheated and shut off. Check the solutions for this light status. • If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receiver setting is turned on in the projector's menu, if available. • The power cord may be defective. Try another power cord. If that doesn't work, disconnect the cord and contact Epson.
Related references Remote Control Operation Projector Feature Settings - Settings Menu Related tasks Replacing the Remote Control Batteries Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control. • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson.
Solutions When Wireless Authentication Fails If you cannot authenticate a wireless connection, try the following solutions: • Make sure the Wireless Mode setting is set to Wireless Lan On. • Check the Security settings and passphrase in the Network Configuration menu. • Check the Event ID number displayed in the Info menu and check the link below to identify the problem.
Solutions When Network Alert E-Mails are Not Received If you do not receive an e-mail alerting you to problems with a projector over the network, try the following solutions: • Make sure the projector is turned on and connected to the network correctly. (If an error shut down the projector, it cannot send an e-mail.) • Make sure you set up the projector e-mail alert settings correctly on the projector's network Notifications menu or in the network software.
Before you call, have the following information ready: • Product name • Product serial number (located on the bottom or rear of the projector, or in the menu system) • Proof of purchase (such as a store receipt) and date of purchase • Computer or video configuration • Description of the problem Purchase Supplies and Accessories You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller.
Technical Specifications These sections list the technical specifications of your projector.
Lens Home Cinema 660: F=1.44 Focal length: 16.7 mm Home Cinema 760HD: F=1.49 to 1.72 Focal length: 16.9 to 20.28 mm Home Cinema 1060: F=1.58 to 1.70 Focal length: 18.2 to 29.
Image size Home Cinema 660: (in native aspect ratio) 23 inches (0.58 m) to 350 inches (8.89 m) Home Cinema 760HD: 33 inches (0.84 m) to 320 inches (8.13 m) Home Cinema 1060: 30 inches (0.76 m) to 300 inches (7.62 m) Projection distance Home Cinema 660: (in native aspect ratio) 34.6 inches (0.88 m) to 411 inches (10.44 m) Home Cinema 760HD: 35.8 inches (0.91 m) to 428.7 inches (10.89 m) Home Cinema 1060: 26.4 inches (0.67 m) to 326 inches (8.
Internal sound system 2 W monaural Noise level 37 dB (Normal Power Consumption mode) 28 dB (ECO Power Consumption mode) Keystone correction angle Vertical: ± 30º (manual); ± 30º (using Auto Keystone) Horizontal: ± 30º (manual) USB Type B port compatibility USB 2.0 compliant for USB display or external mouse USB Type A port compatibility One USB 1.1 and 2.
Projector Dimension Specifications Height (excluding feet) Home Cinema 660/760HD: 3.0 inches (77 mm) Home Cinema 1060: 3.4 inches (87 mm) Width 11.9 inches (302 mm) Depth Home Cinema 660/760HD 9.2 inches (234 mm) Home Cinema 1060: 9.8 inches (249 mm) Weight Home Cinema 660: 5.29 lb (2.4 kg) Home Cinema 760HD: 5.51 lb (2.5 kg) Home Cinema 1060: 5.95 lb (2.
Power consumption Operating: (100 to 120 V) Home Cinema 660/760HD: Normal Power Consumption mode: 296 W ECO Power Consumption mode: 211 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Home Cinema 1060: Normal Power Consumption mode: 315 W ECO Power Consumption mode: 228 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Power consumption Operating: (220 to 240 V) Home Cinema 660/760HD: Normal Power Consumption mode: 282 W ECO Power Consumption mode: 203 W Standby: 2.
Operating altitude Up to 4921 feet (1500 m) 4921 feet (1500 m) to 9843 feet (3000 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) WXGA+ 60 1440 × 900 SXGA 70/75 1152 × 864 60 1280 × 960 60 1280 × 1024 60 1400 × 1050 TV (NTSC) 60 720 × 480 TV (SECAM) 50 720 × 576 TV (PAL) 50/60 720 × 576 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 SXGA 60 1280 ×
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 Refresh rate (in Hz) Resolution (in pixels) VGA 60/72/75/85 640 × 480 SVGA 60/72/75/85 800 × 600 XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 60 1366 × 768 60/75/85 1280 × 800 WXGA+ 60/75/85 1440 × 900 WXGA++ 60 1600 × 900 SXGA 70/75/85 1152 × 864 60/75/85 1280 × 1024 60/75/85 1280 × 960 60/75 1400 × 1050 60
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 UXGA 60 1600 × 1200 WSXGA+ 60 1680 × 1050 SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 WUXGA (Reduced Blanking)2 60 1920 × 1200 SDTV (480i/480p)
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 1 Wide resolution only 2 Home Cinema 1060 only Parent topic: Technical Specifications USB Display System Requirements Your computer system must meet the system requirements here to use the projector's USB Display software.
Requirement Windows Mac Display Resolution between 640 × 480 and 1920 × 1200, 16-bit color or greater Parent topic: Technical Specifications 190
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature. • Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
No. 5 6 Symbol Approved Standards Description IEC60417 Caution, hot surface No.5041 To indicate that the marked item can be hot and should not be touched without taking care. IEC60417 Caution, risk of electric shock No.6042 To identify equipment that has risk of electric shock. ISO3864-B3.6 7 8 9 IEC60417 For indoor use only No.5957 To identify electrical equipment designed primarily for indoor use. IEC60417 Polarity of DC power connector No.
No. 12 Symbol Approved Standards Description — Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. 13 14 15 16 17 18 IEC60417 Protective earth No.5019 To identify any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal of a protective earth electrode. IEC60417 Earth No.
No. Symbol 19 Approved Standards Description ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. 20 — Never look into the optical lens while the projector is on. 21 — To indicate that the marked item don’t place anything on projector. 22 ISO3864 Caution, laser radiation IEC60825-1 To indicate the equipment has a laser radiation part.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Epson, whether in contract, warranty, misrepresentation, fraud, tort, intentional tort, statute, regulation, ordinance, or any other legal or equitable basis. "DISPUTE" DOES NOT INCLUDE IP CLAIMS, or more specifically, a claim or cause of action for (a) trademark infringement or dilution, (b) patent infringement, (c) copyright infringement or misuse, or (d) trade secret misappropriation (an "IP Claim"). You and Epson also agree, notwithstanding Section 1.
WITHOUT THE WRITTEN CONSENT OF ALL AFFECTED PARTIES TO AN ARBITRATION PROCEEDING. 1.6 Arbitration Procedure. If you or Epson commences arbitration, the arbitration shall be governed by the rules of JAMS that are in effect when the arbitration is filed, excluding any rules that permit arbitration on a class or representative basis (the "JAMS Rules"), available at http://www.jamsadr.com or by calling 1-800-352-5267, and under the rules set forth in this Agreement.
c) Arbitration Fees. Epson shall pay, or (if applicable) reimburse you for, all JAMS filings and arbitrator fees for any arbitration commenced (by you or Epson) pursuant to provisions of this Agreement. d) Award in Your Favor.
Trademarks EPSON®, Instant Off®, and Quick Corner® are registered trademarks, Epson iProjectionTM is a trademark, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. Accolade® and PrivateLine® are registered trademarks; DuetTM and SizeWiseTM are trademarks; and Epson StoreSM and Extra CareSM are service marks of Epson America, Inc. Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. AndroidTM and ChromebookTM are trademarks of Google Inc.
A Note Concerning Responsible Use of Copyrighted Materials Copyright Attribution Parent topic: Notices A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume.
