INSTALLATION MANUAL High Security Projector Ceiling Mount MODEL# ELPMBATA Manufactured by: Business Machine Security, Inc. 520 W. Central Ave. Brea, CA 92821 www.LocDown.
Table of Contents Limited Warranty Information....................................................................................... 3 Contact Business Machine Security.............................................................................3 Warning Statement........................................................................................................ 3 Parts List.........................................................................................................................
Business Machine Security Limited Warranty Information Business Machine Security, Inc. warrants the original purchaser of Business Machine Security, Inc. products that they be free of defects in material and workmanship for life from the date of purchase. User assumes all risk and liability resulting from the use of the products, whether used singly or in combination with other goods. Business Machine Security, Inc.
Parts List Installation Tools Pipe Adhesive (provided) Phillips Head Screwdriver (not provided) Mounting Hardware 4mm X 10mm Pan Head Metric Screw (Qty 4) #10 SAE Flat Washer (Qty 4) INSTALLATION MANUAL 4mm X 20mm Pan Head Metric Screw (Qty 4) 3/8” Thick Spacer (Qty 4) 4
Mount Assembly PARTS LEGEND A B C D E F 1-1/2” Threaded Pipe (Not provided) Pipe Adhesive 1-1/2” Pipe Coupler Tensioning Ring Receiver Tray Grid Plate G Pan Head Metric Screw* 4mm X 10mm 4mm X 20mm H I J #10 SAE Flat Washer Screw Lock 3/8” Spacer P Projector (Not included) *see pages 7-9 for proper hardware to use for your model projector GRID PLATE TO RECEIVER TRAY INSTALLATION MANUAL 5
Securing Receiver Tray to Pipe Twist off the cap from the Pipe Thread Adhesive tube (B). Cut off the tip. Apply it to the inside of the coupler (C) at the top, for about 1/4” or approximately three threads. Screw the coupler (C) clockwise (as viewed from below), with the Receiver Tray (E) already assembled, onto the pre-installed 1-1/2” standard pipe threads (A). This connection should be as tight and stable as possible.
Mounting Projector to Grid Plate 1. Turn the projector (P) upside down and place it flat on a soft cloth or packaging material. Remove or adjust the feet to be as flush as possible to the projector bottom. 2. Place the Grid Plate (F) on the bottom of the projector and line it up so the mounting inserts of the projector (P) can be seen through the holes of the Grid Plate (F). (NOTE: see pages 8-9 for which mounting holes to use for your model projector) 3.
Epson Projector Model# 1700c, 1705c, 1710c, 1715c Mounting Inserts Grid Plate Alignment HARDWARE Mounting Inserts: • #10 SAE Flat Washers (Qty 3) • 4mm X 10mm Pan Head Metric Screws (Qty 3) Epson Projector Model# S5, 77c, 83+, 822+, 400W Mounting Inserts Grid Plate Alignment HARDWARE Mounting Inserts: • #10 SAE Flat Washers (Qty 3) • 4mm X 10mm Pan Head Metric Screws (Qty 3) • 4mm X 20mm Pan Head Metric Screws (Qty 3) (400W model only) • 3/8 Spacers (Qty 3) (400w model only) INSTALLATION MANUAL 8
Epson Projector Model# 6110i Mounting Inserts Grid Plate Alignment HARDWARE NOTE: For updated information on Mounting Inserts: compatibility with the latest Epson • #10 projector models, visit www.epson.
Locking Grid Plate to Receiver Tray 1. After the Receiver Tray (E) has been attached to the ceiling and the projector has been attached to the Grid Plate (F), slide the Grid Plate (F) into the Receiver Tray (E). Before completely closing the mount, route the cables that are running down the 1-1/2” Pipe (A) and out the center of the Receiver Tray (E). (See figure 6) Slide the Grid Plate (F) in while guiding the cables into a slot located in the back of the Grid Plate (F). (See figure 7) 2.
Adjusting Mount 1. To align the projector, simply grab a hold of either side of the mount and gently adjust by lifting up and pushing down until you have the proper registration. If you wish to add or lessen the tension, turn the Tension Ring until the desired amount has been achieved. The Tension Ring can be turned to lock in the registration once the installation is complete.
