Specifications

ManualsBrandsEpson ManualsProjector MountsELPHB800

ELPHB800

Installation Instructions

The entire installation instructions should be fully read and understood, including all of the safety

precautions, before beginning installation. The installation instructions should be read, understood

and followed to prevent personal injury or property damage. Keep these installation instructions in

an easily accessible location for future reference.

Installation methods:

° Fixed Height Ceiling Installation

— Best for short ceilings, eight (8’) or lower. Removal of the

center adjustable suspension in needed.

° Adjustable Height Ceiling Installation

—Best for high ceilings, nine (9’) feet or higher.

° Wall Mount Installation

—For installing the Digital Projector Mount on a rear wall.

° ELPMBAPL

—(Optional) 26" to 47" Adjustable height ceiling adapter.

Before Installation

The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is

five (5) times the weight of the projector you are installing. Consult the projector’s documentation for weight

specifications. The ceiling structure must be capable of supporting a max weight of 25 lbs., the weight of the

projector. If not, the ceiling must be reinforced. Proper installation procedure by qualified personnel as

outlined in the installations instructions must be adhered to. Failure to do so could result in serious personal

injury.

The Projector Mount utilizes the following hardware. Note that the letters associated with the hardware on this

list correspond to the letters listed in the instructions for each installation method. If any of the following

hardware is missing STOP. Contact Epson for proper hardware.

. Four

(

)

M4 x 10

(

)

Philli

s screws

(

lied

)

B. One (1) mounting bracket (supplied)

C. Digital Projector (not included)

D. Assembly mount (supplied)

Hardware descri

tion

NOTE: Hardware item (E) is what secures the Digital Projector Mount to a simple wood stud on your wall

ceiling. For all installations other than single wood mounting make sure you consult with your local hardware

store staff for the type of hardware that works best for your installation environment.

E. SINGLE WOOD STUD: If mounting on a single wood stud use the three (3) #14 x 2" Lag screws (supplied)

Use the mounting points on the center of the plate as indicated in the assembly diagram.

° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag screws or commercially

available hardware (depending on the installation requirements). Use the mounting points found on the outer

points of the mounting plate as indicated in the assembly diagram.

F. Allen wrench (supplied)

Summary of content (5 pages)

PAGE 1
Hardware description The Projector Mount utilizes the following hardware. Note that the letters associated with the hardware on this list correspond to the letters listed in the instructions for each installation method. If any of the following hardware is missing STOP. Contact Epson for proper hardware. A. Four (4) M4 x 10 (mm) Phillips screws (supplied) ELPHB800 Installation Instructions B.
PAGE 2
Tools Needed for Installing the Projector Mount Getting the projector ready You need the following tools to install the Projector Mount: Before you start the installation process, prepare your Digital Projector by performing the following steps (FIGURE 1). • Phillips head screwdriver (not included) • Allen wrench (included) 1. Turn the projector (C) upside down and place it on a clean flat surface, preferably on a towel.
PAGE 3
FIGURE 2 Ceiling plate Wood stud E Remove (M8) Hex head screws, flat washers and star lock washers Center of wood stud D Ceiling structure Remove the center extension from the assembly Insert and rotate 180° lock down the safety screw B NOTE: The shape of each mount is different. Align each bracket hole with the projector mounting point and attach.
PAGE 4
Adjustable Height ceiling Installation FIGURE 3 E Complete the following steps to install the projector mount and projector on your ceiling with the optional suspension adapter. Wood stud This installation works best with high ceilings (FIGURE 3). Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector mount with the arrow pointing toward your screen. 6. Use the Allen wrench (F) to remove the upper plate from the mount assembly (D). 7.
PAGE 5
Wall Mount Installation FIGURE 4 Complete the following steps to install the projector mount and projector to your wall. (FIGURE 4) Wall wood stud Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector mount with the arrow pointing toward your screen. NOTE: Follow step 3 to secure the extension to the mount assembly. 15. Secure the upper plate to the wall using the commercially available hardware (E) suitable for your environment.