Color Copy Station Color Copy Station Setup Guide Printed in Japan 00.
L R4C3900 Rev. D A5 size 4/6/01 COVER2.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Where to Find Information Before using the EPSON AcuLaser Color Copy Station 8500, be sure to follow the instructions in the following manuals. EPSON AcuLaser Color Copy Station 8500 Setup Guide (this manual) Explains how to assemble the copy station’s components and test basic copying operation.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 FRONT.FM Pass 3 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum FRONT.FM Pass 3 _______ _______ _______ DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: EPSON AMERICA, INC.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUPG.TOC Pass 3 Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Finding a Place for the Copy Station . . . . . . . . . . . . . . . . . . . . . . . 3 Checking the Copy Station Components . . . . . . . . . . . . . . . . . . . . 5 Setting Up the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L R4C3900 Rev. D A5 size 4/6/01 SETUPG.TOC Pass 3 iv Proof Sign-off: T.Ichihashi M.Miyazaki K.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Safety Instructions Important Safety Instructions Read all of these instructions and save them for later reference. ❏ Follow all warnings and instructions marked on the copy station. ❏ Do not block or cover the openings in the printer or the scanner. ❏ Do not insert objects through the slots in the printer or the scanner. ❏ Do not spill liquid on the copy station.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ ❏ If you plan to use the copy station in Germany, observe the following: To provide adequate short-circuit protection and overcurrent protection for this product, the building installation must be protected by a 10 Amp or 16 Amp circuit breaker.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Finding a Place for the Copy Station Before assembling the copy station, find a place that meets the following requirements. ❏ Leave adequate room for easy operation, maintenance, and ventilation. The minimum space requirements are shown below.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 _______ _______ _______ ❏ Place the copy station on a flat, stable surface. ❏ The copy station will operate properly under the following conditions: Temperature: Humidity: c 10 to 35°C 20 to 80% Caution: ❏ Avoid locations that are subject to shock, direct sunlight, extreme variation in temperature or humidity, excessive heat, moisture, or dust.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Checking the Copy Station Components The copy station consists of a cabinet and central control panel, a scanner (EPSON GT-10000+ or EPSON EXPRESSION 1640XL), a printer (EPSON AcuLaser C8500), and a large capacity paper unit. Make sure you have the boxes for each of the copy station components listed below.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 _______ _______ _______ The copy station accessories box contains the items listed below. Confirm that none of these items is missing or damaged.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Setting Up the Cabinet Make sure the cabinet box contains all of the parts listed below. Then follow the steps in this section to assemble the cabinet and to install the control panel.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 _______ _______ _______ Assembling the Cabinet c Caution: The cabinet is bulky and requires two people for assembly or handling. 1. Place flat washers and spring washers onto four M8 × 35 bolts as shown below. Align the positioning marks on the right support and the right frame, then fasten the support to the frame with the bolts.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 3. Use M4 × 10 screws to fasten joint A and the front panel to the frame in the order shown below. Fasten the joint only loosely in this step. It is to be fastened securely later in the assembly procedure. ➂ ➀ ➂ ➁ joint A front panel 4. Fasten the caster fixer and the stoppers to the bottom of the frame with four M4 × 10 screws.
R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 _______ _______ _______ 5. Fasten the top panel onto the frame with seven M4 × 10 screws. top panel 6. Fasten joint B to the frame with eight M4 × 10 screws. Then securely fasten joint A, which was installed in step 2. 1 2 3 4 5 A A A A joint B 10 Setting Up the Cabinet 985 mm L The stand height is adjustable to five positions. When the stand is in position 3, 4, or 5, use holes A to fasten joint B.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 7. Attach cable clips to the cabinet as needed. Holes are provided for this purpose in various positions around the cabinet. w c Warning: Do not climb onto the cabinet. Doing so may result in injury, or may damage the cabinet.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 1. Plug the shielded control panel cable into the control panel’s interface connector, located on the bottom of the control panel. control panel cable interface connector 2. If you plan to attach the control panel to the cabinet, fasten the control panel shelf onto the bottom of the control panel using the screws included with the copy station accessories.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 3. Insert the control panel shelf straight into the opening on the front of the cabinet’s top panel. Note: If you do not plan to attach the control panel to the cabinet, attach the panel cover included in the cabinet box to the opening on the cabinet’s top panel. 4. Secure the control panel shelf with the screws included with the cabinet.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Setting Up the Scanner To prepare the scanner for use with the copy station, you need to install the scanner interface board and place the scanner onto the cabinet, as explained below. The setup procedure is the same for the EPSON GT-10000+ and EPSON EXPRESSION 1640XL. However, the illustrations used in this manual are of the EPSON GT-10000+. 1.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 3. Use a cross-head screwdriver to remove the two screws securing the shield plate to the optional interface slot; then remove the plate. Note: Keep the screws and the shield plate in a safe place. You will need to reattach the plate if you remove the interface board later. c Caution: Static electricity can damage electronic components.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 5. Secure the board with the retaining screws. 6. Place the scanner onto the cabinet in the direction shown below.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Setting Up the Printer To prepare the printer for use with the copy station, you need to install the interface board, ROM module, and large capacity paper unit, then place the printer into the cabinet. Follow the steps in this section. w c Warning: Be careful when working inside the printer as some components are sharp and may cause injury.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 3. Remove the two screws securing the shield plate on the rear of the printer; then remove the plate. Note: ❏ You will need the screws to secure the printer interface board later in this procedure. ❏ Keep the shield plate in a safe place. You will need to reattach it if you remove the interface board later. 4.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 5. Remove the screws on the right cover. 6. Slide the right cover backward and remove it as shown below.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 7. Identify the socket for the printer interface board. printer interface board socket c Caution: You should not remove any modules from the circuit board. Otherwise, the printer will not work. 8. Insert the interface connectors through the slot at the back of the printer, then press the interface board firmly onto the socket.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 9. Secure the interface board with the screw included with the copy station accessories. Note: Use a magnetic cross-head screwdriver to prevent the screw from dropping inside the printer. 10. Secure the printer interface board with the two screws which you removed from the shield plate in step 6.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 11. Identify the slots for the ROM module. ROM module slot A 12. Insert the module all the way into slot A, making sure that the gold contact side of the module faces up. The X tab on the left of the slot will jut out when the module is inserted correctly. c 22 Caution: ❏ Do not force the ROM module into the slot. ❏ Be sure to insert the module facing the correct way.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 13. To reattach the right cover, align the bottom of the cover with the right side of the printer, then fit the pins on the top of the cover onto the holes on the printer. 14. Secure the right cover with the screws, then close the front cover and push the paper path unit back into the printer. 15. Install the large capacity paper unit as explained in the printer’s manual.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 16. Roll the large capacity paper unit and the printer into the cabinet. 17. Lock the four casters on the bottom of the large capacity paper unit. w 24 Warning: Make sure the casters are securely locked. Otherwise, the printer may move and cause an accident.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Setting Up the Copy Station Once you’ve added each device to the cabinet, you are ready to set up the copy station. This process involves connecting the interface cables and power cords. Follow the steps in this section. Connecting Interface Cables The copy station devices are connected as shown below.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Follow the steps in this section to connect the interface cables. 1. Make sure the printer and scanner are not plugged in. 2. Plug the control panel cable into the printer's serial interface connector. Make sure the locks on both sides of the connector snap into place. 3. Plug the scanner cable into the scanner’s interface connector.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 4. Plug the other end of the cable into the connector on the printer. Plugging in the Printer and Scanner The printer and scanner power is supplied through separate power cords. Take note of the Warnings and Cautions below, then follow the steps in this section to plug in the printer and the scanner. w Warning: ❏ Use only the power cords that come with the printer and scanner.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 c Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Caution: ❏ Do not unplug a device when its power is on. ❏ When unplugging a power cord, grasp it by the plug—not the cord. Plugging in the printer 1. Check the label on the printer to make sure that the voltage required by the printer matches that of the electrical outlet it will be plugged into. Also, make sure that you have the correct power cord for your power source. 2.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Plugging in the scanner 1. Check the label on the back of the scanner to make sure that the voltage required by the scanner matches that of the electrical outlet it will be plugged into. Also, make sure that you have the correct power cord for your power source. 2. Make sure the scanner is turned off. The power is off when the P OPERATE button is raised. 3.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Testing the Copy Station You can check the operation of the copy station by making a few test copies. You will need to prepare a document to copy and a stack of paper that is the same size as your document, then follow the steps in this section to make your copies.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 2. Press down on the metal plate in the cassette until it clicks into place. 3. Press on the side and back paper guides, then slide them outward until they are wide open enough to accommodate the size of paper you want to load.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 4. Fan a stack of plain paper and insert it into the cassette. Make sure that all the paper is under the retaining clip on the right side of the cassette. Note: Use paper with no creases or wrinkles. 5. Slide the paper guides until they just touch the edges of the paper.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Note: Make sure you adjust the side paper guide to the correct position, because the copy station automatically senses the size of paper loaded in the cassette from the position of this paper guide.
L R4C3900 Rev. D A5 size 4/6/01 SETUP.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ Copying Once you’ve loaded paper and turned on the copy station, you’re ready to make test copies. Follow these steps. 1. Make sure the scanner's READY light is on. 2. Open the document cover. 3. Place your document on the document table, with the side to be scanned facing down. Make sure that the document is carefully aligned.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Note: An area 2 ± 1.5 mm in from both horizontal and vertical rulers will not be scanned. 2 ± 1.5 mm 2 ± 1.5 mm Document 4. Close the document cover gently so that the document does not move. Note: Make sure the document is flat against the glass surface, otherwise the image will appear fuzzy and out of focus.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 _______ _______ _______ 6. Select the paper size and orientation that matches the size of the document and the direction in which it is placed on the document table. Select Output Paper A4 Plain Magazine Lower Cassette MP Tray 1 A4 A4 Current 2 B5 B5 3 A3 A3W Plain paper Change Cancel 7. Press the x start button on the copy station’s control panel. The document is scanned and then printed.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 SETUP.FM Pass 3 Selecting a Language The default language for the LCD touch screen is English. However, German, Spanish, French, Italian, Portuguese, and English (USA) are also available. If you want to change the language, follow the steps below. 1. Press the Admin button on the control panel. Admin button 2. Press the Admin. Set button on the touch screen.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum SETUP.FM Pass 3 3. Press the Select Language button. Select Administrator Items Key Tone ON OFF Set Default Copy Job Standy Control ON OFF Color Calibration Auto Feed ON OFF Copy Unit Select Language Restore Defaults Copy Unit Restore Defaults Exit 4. Choose a language and press Exit.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Appendix A Installing EPSON Network Image Express EPSON Network Image Express allows the scanner to be shared on a network without the need for a scanner server PC. This appendix explains how to install EPSON Network Image Express in the copy station. See the manual that comes with this product for more information. EPSON Network Image Express 1.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum APPNDX.FM Pass 3 _______ _______ _______ 3. Remove the connector cover on the left side of the control panel as shown below. 4. Identify the connectors and switch on the side panel of Network Image Express.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 5. Slide the power supply mode switch up, which is the off position. The power to Network Image Express is turned on automatically when the scanner power is turned on. 6. Pass one end of the SCSI cable included with Network Image Express through the opening on the left side of the control panel, then connect it to the SCSI connector on Network Image Express.
L R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 8. Pass the 10BaseT or 100BaseTX network cable through the opening on the control panel, and connect it to the network connector. 9. Pass the power cord through the opening on the control panel and connect it to the DC inlet. c 42 Caution: Use only the AC adapter and the power cord included with Network Image Express. Using other adapters may cause the system to malfunction.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 10. Insert the left side of Network Image Express into the opening on the control panel. 11. Push the right side of the Network Image Express gently into place.
L R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 12. Secure Network Image Express to the control panel with the two screws included in the copy station accessories. 13. Close the translucent cover. 14. Attach a touch fastener strip to the AC adapter.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 15. Attach the other touch fastener strip to the cabinet, and then attach the AC adapter to the cabinet by joining the two strips. . 16. Install the cable clips at the following locations, then secure the Network Image Express cables with the clips.
L R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ 17. Connect the power cord of the scanner and then turn on the scanner. 18. Plug in the power cord of the AC adapter. Note: ❏ Network Image Express has a built-in SCSI terminator. ❏ The fixed SCSI ID number for Network Image Express is 7. Use any available number other than 7 for the scanner. See the scanner manual to learn how to set the ID number.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Appendix B Contacting Customer Support If your EPSON product is not operating properly and you cannot solve the problem using the troubleshooting information in your product documentation, contact customer support services for assistance. If customer support for your area is not listed below, contact the dealer where you purchased your product.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum APPNDX.FM Pass 3 _______ _______ _______ For Users in North America If you purchased your printer in the United States or Canada, EPSON provides technical assistance 24 hours a day through the electronic support services and automated telephone services listed in the following table: Service Access World Wide Web From the Internet, you can reach EPSON Support at http://support.epson.com.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Before you call, please have the following information ready: ❏ Product name ❏ Product serial number ❏ Proof of purchase (such as a store receipt) and date of purchase ❏ Computer configuration ❏ Description of the problem Note: For help using any other software on your system, see the documentation for that software for technical support information.
L R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ ❏ To E-mail EPSON Technical Support: http://www.epson.co.uk/support/email/ ❏ For a full list of EPSON Customer and Warranty Support services: http://www.epson.co.uk/support/ Support via telephone Our Customer and Warranty Support teams can be contacted by calling 0870 163 7766 in the UK or 0044 0870 163 7766 from the Republic of Ireland.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum _______ _______ _______ R R4C3900 Rev. D A5 size 4/6/01 APPNDX.FM Pass 3 For Users in Australia EPSON Australia wishes to provide you with a high level of customer service. In addition to your product documentation, we provide the following sources for obtaining information: EPSON FAXBACK EPSON FAXBACK will fax you the latest specifications and pricing for most EPSON products offered in Australia.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum APPNDX.FM Pass 3 _______ _______ _______ EPSON Helpdesk EPSON Helpdesk is provided as a final backup to make sure our clients have access to advice. Operators on the Helpdesk can aid you in diagnosing hardware and software problems. They can also advise you on the latest EPSON products and where the nearest dealer or service agent is located. Many types of queries are answered here.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 APPNDX.FM Pass 3 For Users in Malaysia Contacts for information, support, and services are: World Wide Web (www.epson.com.my) Information on product specifications, drivers for download, Frequently Asked Questions (FAQ), and Email Enquiries are available.
L R4C3900 Rev. D A5 size 4/6/01 Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum APPNDX.FM Pass 3 _______ _______ _______ For Users in Hong Kong To obtain technical support as well as other after-sales services, users are welcome to contact EPSON Hong Kong Limited.
Proof Sign-off: T.Ichihashi M.Miyazaki K.Norum R R4C3900 Rev. D _______ _______ _______ A5 size 4/6/01 APPNDX.
EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA, INC. EPSON UK LTD. 20770 Madrona Ave. Campus 100, Maylands Avenue, P.O. Box 2842 Hemel Hempstead, Herts, Torrance, CA 90509-2842 HP2 7TJ, U.K. Phone: (800) 922-8911 Phone: (+44) 01442 261144 Fax: (310) 782-5220 Fax: (+44) 01442 227227 EPSON DEUTSCHLAND GmbH EPSON FRANCE S.A. Zülpicher Straße 6, 68 bis, rue Marjolin 40549 Düsseldorf Germany 92300, Levallois-Perret, France Phone: (0211) 56030 Phone: 33.1.40.87.37.
Color Copy Station Color Copy Station Setup Guide Printed in Japan 00.
