User Manual

ManualsBrandsEpson ManualsOffice ElectronicsEpson PictureMate PM-400 Wireless Compact Color Photo Printer

Start Here

Load paper

1 Slide the edge guide to the right.

2 Load one of the included 4 x 6-inch sheets, glossy or

printable side up and short edge ﬁrst.

3 Slide the edge guide against the paper, but not too tightly.

4 Select Change on the LCD screen and press the

OK button.

5 Select 4x6in and press the OK button.

6 Select Prem. Glossy and press the OK button.

7 Press the OK button again to conﬁrm the paper settings.

Read these instructions before using your product.

Unpack

4 x 6-inch

paper

Note: Do not open the ink cartridge package until you are ready to

install the ink. Cartridges are vacuum packed to maintain reliability.

Remove all protective materials from the product.

Turn on and configure

1 Connect the power adapter to the side of the product.

Then connect one end of the power cord to the power

adapter and the other end to an electrical outlet.

Caution: Do not connect to your computer yet.

2 Open the cover, raise the LCD screen, and turn on the

product.

3 To select English as your language, press the OK button.

If you want to change the language, press or to

select it, then press the OK button.

Note: You can change the language later using the product’s

control panel. For more information, see the online User’s Guide.

Install ink cartridge

1 Unpack the initial ink cartridge and completely remove the

yellow tape only.

Caution: Do not remove any other labels or seals, or ink

may leak.

2 Remove the cap and carefully dispose of it.

Caution: Do not touch the areas shown below. Doing so may

prevent normal operation and printing.

3 Open the inner cover.

Caution: Do not touch the ﬂat white cable.

4 Hold the cartridge with the green chip facing towards you

and insert the cartridge at an angle as shown. Then press

the ink cartridge down until it clicks into place.

Caution: Make sure to insert the ink cartridge in the correct

direction or you may damage the product.

5 Close the inner cover.

6 Press the button to start charging the ink.

Ink charging takes approximately 4 minutes. Ink charging

is complete when you see the home screen displayed on

the LCD screen.

Caution: Don’t turn off the product or open the inner cover while

it is charging or you’ll waste ink.

Note:

• The printer is designed for use with Epson

cartridges only, not

third-party cartridges or ink.

• The cartridge included with the printer is designed for printer

set up and not for resale. After some ink is used for charging,

the rest is available for printing.

PM-400

Summary of content (4 pages)

PAGE 1
2 Open the cover, raise the LCD screen, and turn on the PM-400 3 Open the inner cover. product. Start Here 4 Load paper 1 Slide the edge guide to the right. Read these instructions before using your product. 1 Unpack 3 To select English as your language, press the OK button. If you want to change the language, press select it, then press the OK button. or to Note: You can change the language later using the product’s control panel. For more information, see the online User’s Guide.
PAGE 2
Open the cover, raise the LCD screen, and turn on the PM-400 3 Open the inner cover. product. Start Here 4 Load paper 1 Slide the edge guide to the right. Read these instructions before using your product. 1 Unpack 3 To select English as your language, press the OK button. If you want to change the language, press select it, then press the OK button. or to Note: You can change the language later using the product’s control panel. For more information, see the online User’s Guide.
PAGE 3
5 Connect and print Your product provides several ways to print, both at home and on the road: • To connect your product to a computer, see “Computer setup.” • To connect your product to a mobile device on the road, see “Mobile setup.” • To print from a memory card or digital camera, see the Quick Guide. Mobile setup ollow the steps here to connect your product wirelessly to F a mobile device without requiring a wireless router or access point (Wi-Fi Direct®).
PAGE 4
5 Connect and print Your product provides several ways to print, both at home and on the road: • To connect your product to a computer, see “Computer setup.” • To connect your product to a mobile device on the road, see “Mobile setup.” • To print from a memory card or digital camera, see the Quick Guide. Mobile setup ollow the steps here to connect your product wirelessly to F a mobile device without requiring a wireless router or access point (Wi-Fi Direct®).