Quick Start Guide

ManualsBrandsEpson ManualsProjectorsHome Cinema 5050UB 4K PRO-UHD 3-Chip HDR Projector, 2600 lumens, UltraBlack, HDMI, Motorized Lens, Movies, Gaming - White

Table Of Contents

Quick Setup

IMPORTANT: Before using this product, make sure you read these instructions

and the safety instructions in the online User’s Guide.

Choose a location

Keep the projector level and place it at a height so its lens is even with the top

or bottom of the screen and is centered horizontally. If this isn’t possible, use

the lens shift feature or the keystone correction button on the projector to

reposition the image (see “Adjust the image”).

In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet

(10 m) of the projector. Use the image below to determine the viewing distance

for 3D projection (the shading represents the 3D viewing area):

See the online User’s Guide for more information on where to place your

projector.

Connect the projector

Choose from the following connections. For additional connection types, see

the online User’s Guide.

Video device

Home Cinema 5050UBe: Remove the cover as shown below.

Connect multiple video devices and use the Source buttons on the remote

control or the Source button on the projector to switch between

them.

HDMI cable

Optical HDMI

Note: When connecting a source that requires HDCP 2.2, you must use

the HDMI1 port.

WirelessHD™ Transmitter (Home Cinema 5050UBe)

Follow these steps to set up the included WirelessHD Transmitter.

HDMI

Place the transmitter within 32 feet (10 m) of the projector. Make sure the

front of the transmitter faces the front of the projector. See the online

User’s Guide for more information on the WirelessHD transmission range.

32 ft

(10 m)

16 ft

(5 m)

32 ft (10 m)

16 ft (5 m)

Note: Do not place the transmitter on a metal surface, as this may

interfere with the signal. Make sure there are no obstructions between

the transmitter and the projector.

Plug the AC adapter into the transmitter and a wall outlet.

Connect the HDMI cables to your video input devices and the HDMI ports

on the side and back of the transmitter. You can connect up to four input

devices to the transmitter. See “Viewing WirelessHD content” on the back

of this sheet for information on switching between input sources.

Note: You can connect tablets, smartphones, and other devices that

support the MHL™ standard to the HDMI port on the side of the

WirelessHD Transmitter. Some devices may require an adapter or may not

require an MHL cable. Not all features or functions may be supported.

Check your device’s documentation for more information.

To use the transmitter as a pass-through device to a television or other

display, connect an HDMI cable to the display device and the HDMI output

port on the rear of the transmitter. See “Viewing WirelessHD content” on

the back of this sheet for information on switching between wireless and

wired display modes.

Home Cinema 5050UB/5050UBe

Summary of content (4 pages)

PAGE 1
Home Cinema 5050UB/5050UBe Quick Setup WirelessHD™ Transmitter (Home Cinema 5050UBe) Follow these steps to set up the included WirelessHD Transmitter. IMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User’s Guide. Choose a location Keep the projector level and place it at a height so its lens is even with the top or bottom of the screen and is centered horizontally.
PAGE 2
Turn on your equipment Using the remote control 1 2 Install the batteries as shown (two AA batteries). Turn on your video source. Plug in the projector. Turn projector on 3 Choose which source to display Press the power button on the projector or the On button on the remote control. The shutter opens and the power light flashes blue, then stays on.
PAGE 3
4 ress the Lens button on the remote control again and use the P buttons to reduce or enlarge the image. and 5 Press the Lens button on the remote control again and use the , and buttons to reposition the image. , Note: If the glasses don’t automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds.
PAGE 4
Troubleshooting Where to get help If you see a blank screen or the No signal message after turning on your video device or computer, check the following: Manuals •• •• •• Make sure the power light on the projector is blue and not flashing. ress the P Source button on the projector or one of the Source buttons on the remote control to switch to the correct image source, if necessary.