User's Guide - 1810.
User's Guide - 1810.book Page 2 Monday, September 10, 2007 6:39 PM Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
User's Guide - 1810.book Page 3 Monday, September 10, 2007 6:39 PM Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Additional Components. . . . .
User's Guide - 1810.book Page 4 Monday, September 10, 2007 6:39 PM 2 Presenting with the Remote Control 3 Connecting to Computers and Other Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 . . . . . . . . 27 Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 28 Switching Between Picture Sources . . . . . . . . . . . . . . . . 28 Turning Off the Picture and Sound . . . . . . . . . .
User's Guide - 1810.book Page 5 Monday, September 10, 2007 6:39 PM 4 Fine-Tuning the Projector . . . . . . . . . . . . . . . . . . . 47 5 Maintaining the Projector . . . . . . . . . . . . . . . . . . . 63 6 Solving Problems Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 49 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Six-Axis Color Adjustment. . . . . . . .
User's Guide - 1810.book Page 6 Monday, September 10, 2007 6:39 PM A Projector Installation . . . . . . . . . . . . . . . . . . . . . . . . 85 B Technical Specifications . . . . . . . . . . . . . . . . . . . . . 87 C Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 93 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 95 Index . . . . . . . . . . . . . . . . . .
User's Guide - 1810.book Page 7 Monday, September 10, 2007 6:39 PM - Welcome The PowerLite ® 1810p is an easy-to-use projector that weighs less than 7 pounds. The projector offers up to 3500 lumens of brightness. You can connect it to a wide range of computers and video sources. Easy setup, control, and security: ■ 5-second startup time and Instant Off ® feature for fast setup and shut down ■ Automatic digital keystone correction ■ 1.
User's Guide - 1810.book Page 8 Monday, September 10, 2007 6:39 PM Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints.
User's Guide - 1810.book Page 9 Monday, September 10, 2007 6:39 PM ■ presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club—and it’s free.
User's Guide - 1810.book Page 10 Monday, September 10, 2007 6:39 PM Unpacking the Projector After unpacking the projector, make sure you have all these parts: Projector Power cable PDF manual and registration CD-ROM Remote control and 2 AAA batteries VGA computer cable Carrying case Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.book Page 13 Monday, September 10, 2007 6:39 PM 1 Displaying and Adjusting the Image W hether you’re presenting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.
User's Guide - 1810.book Page 14 Monday, September 10, 2007 6:39 PM Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 85 for details. If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
User's Guide - 1810.book Page 15 Monday, September 10, 2007 6:39 PM Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 11.
User's Guide - 1810.book Page 16 Monday, September 10, 2007 6:39 PM Follow these steps to turn on the projector: 1. Open the A/V mute slide (lens cover). note You can set the projector to automatically turn off the projector lamp and enter “sleep mode” when it has not received any signals for 30 minutes. This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the P Power button.
User's Guide - 1810.book Page 17 Monday, September 10, 2007 6:39 PM 3. Press the P Power button on the remote control or on top of the projector. The projector beeps once and the Power light flashes green as the projector warms up, then an image begins to appear. When the Power light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 57. warning Never look into the lens when the lamp is on.
User's Guide - 1810.book Page 18 Monday, September 10, 2007 6:39 PM Shutting Down the Projector note Lamp life results will vary depending on mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. This projector incorporates Instant Off technology. To turn it off, you can press its P Power button as described below, unplug it, or turn off a power switch that supplies power to the projector.
User's Guide - 1810.book Page 19 Monday, September 10, 2007 6:39 PM Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you don’t see the image you are trying to project, try the following: ■ Make sure the cables are connected correctly, as described beginning on page 35. ■ Make sure the Power light is green and not flashing and the A/V mute slide (lens cover) is open.
User's Guide - 1810.book Page 20 Monday, September 10, 2007 6:39 PM ■ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced.
User's Guide - 1810.book Page 21 Monday, September 10, 2007 6:39 PM Adjusting the Image Once you see your image, you need to make certain adjustments: ■ If the image is too high or too low, reposition it as described below. ■ To focus or zoom your image, see page 22. ■ If the image isn’t square, see page 22. ■ To quickly adjust the color, brightness, or contrast, see page 25. ■ To change the image aspect ratio, see page 26. ■ If you need to fine-tune the image and/or sound, see Chapter 4.
User's Guide - 1810.book Page 22 Monday, September 10, 2007 6:39 PM Focusing and Zooming the Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring on the projector to reduce or enlarge the image. Focus Zoom If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 30 for instructions.
User's Guide - 1810.book Page 23 Monday, September 10, 2007 6:39 PM You see a projected message: 2. Aim the projector so the message appears near the middle of the screen. Then use the zoom ring to enlarge the image so the white frame (not shown above) extends beyond the edges of the screen on all sides. 3. Press the Quick Setup button again. Two white boxes flash momentarily onto the screen, and the adjustment is complete. Your projected image now fits on the screen (some slight overlap is normal).
User's Guide - 1810.book Page 24 Monday, September 10, 2007 6:39 PM You see this screen: 5. Use the pointer button on the remote control (or the arrow buttons on the projector) to select the corner you want to adjust, and press Enter. 6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape. 7. Repeat steps 5 and 6 as needed to adjust any remaining corners. 8. When done, press Menu to exit the menu system.
User's Guide - 1810.book Page 25 Monday, September 10, 2007 6:39 PM You can manually adjust the shape of the image to compensate for vertical and horizontal keystone distortion. First make sure the Keystone setting in the projector’s menu system is set to H-Keystone or V-Keystone: 1. Press the Menu button on the remote control (or on the projector’s control panel). note The projector’s arrow buttons may already be in Keystone correction mode if you haven’t used Quick Setup or Quick Corner. 2.
User's Guide - 1810.book Page 26 Monday, September 10, 2007 6:39 PM Press the Color Mode button on the remote control, and then select from one of these options: ■ Presentation: For making color presentations in a bright room. ■ Text: For making black-and-white presentations in a bright room. ■ Theatre: For watching movies in a darkened room; gives images a natural tone. ■ Photo: For vivid, high-contrast still images in a bright room.
User's Guide - 1810.book Page 27 Monday, September 10, 2007 6:39 PM 2 Presenting with the Remote Control T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet away. You can use the remote control to adjust the picture and sound (page 28) or as a pointer to highlight your presentation (page 31).
User's Guide - 1810.book Page 28 Monday, September 10, 2007 6:39 PM note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Make sure batteries are installed as described on page 70. Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 20 feet of the projector.
User's Guide - 1810.book Page 29 Monday, September 10, 2007 6:39 PM After you select a source, the screen goes dark for a moment before the image appears. Turning Off the Picture and Sound You can temporarily turn off the image and sound when you want to redirect your audience’s attention. There are two ways to do this: ■ Close the A/V mute slide, as shown below: ■ Press the A/V Mute button on the remote control. This turns the image black and stops the sound.
User's Guide - 1810.book Page 30 Monday, September 10, 2007 6:39 PM Stopping Action You can use the remote control to stop the action in your video or computer image. note This function pauses the image, not the sound. Because the source continues to transmit signals, when you resume the action, it won’t be at the point you stopped it. ■ To stop the action and keep the current image on the screen, press the Freeze button. The sound continues. ■ To restart it, press the Freeze button again.
User's Guide - 1810.book Page 31 Monday, September 10, 2007 6:39 PM Controlling the Volume To change the volume, press the control. or button on the remote note To temporarily shut off the sound and picture, press the A/V Mute button or close the A/V mute slide. You can also adjust the volume using the projector’s menu system. See page 54. Highlighting Your Presentation You can display a pointer to call out important information on the screen.
User's Guide - 1810.book Page 32 Monday, September 10, 2007 6:39 PM 3. When you’re done using the pointer, press Esc to clear the screen. Customizing the Pointer Tool You can change the appearance of the pointer by choosing from three alternative shapes. 1. Press the Menu button on the remote control, highlight the Settings menu, highlight Pointer Shape, and press Enter. You can select one of the pointer shapes shown at the left. 2. Select the shape you want and press Enter. 3.
User's Guide - 1810.book Page 33 Monday, September 10, 2007 6:39 PM ■ Use the pointer button to move the pointer on the screen. ■ Press the Enter button once to left-click, or press it twice to double-click. Press the Esc button to right-click. ■ To drag-and-drop, hold down the Enter button. Then use the pointer button to drag the object. When it’s where you want it, release the Enter button.
User's Guide - 1810.book Page 34 Monday, September 10, 2007 6:39 PM 4. When done, press Menu to exit the menu system. Setting the Remote Control ID note If you’re using a remote control ID other than the default ID of zero, you have to set the ID each time you turn on the projector. The remote control’s default ID is zero. This lets you operate any projector. To set it to operate a specific projector, follow these steps: 1. Point the remote control at the projector you want to be able to operate. 2.
User's Guide - 1810.book Page 35 Monday, September 10, 2007 6:39 PM 3 Connecting to Computers and Other Equipment T his chapter tells you how to connect the projector to a notebook or desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera.
User's Guide - 1810.book Page 36 Monday, September 10, 2007 6:39 PM Connecting to a Computer You can connect the projector to any computer that has a standard video output (monitor) port, including desktop models, PC notebook computers, MacBook, PowerBook, and iBook computers, and hand-held devices. If you want to use the projector’s remote control as a wireless mouse to operate your computer during presentations, see page 37.
User's Guide - 1810.book Page 37 Monday, September 10, 2007 6:39 PM 4. When you’ve finished making any connections, see page 15 for instructions on turning on the projector and adjusting the image. Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter (using the Computer 1 or Computer 2 port), you can use the projector’s remote control as a wireless mouse.
User's Guide - 1810.book Page 38 Monday, September 10, 2007 6:39 PM Connecting to Video Equipment RCA connector (composite video) S-video connector You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has a yellow RCA-style video output connector, see “Connecting a Composite Video Source” on page 39.
User's Guide - 1810.book Page 39 Monday, September 10, 2007 6:39 PM Connecting a Composite Video Source 1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: 3. If you want to play sound through the projector, see page 44 for instructions on connecting audio cables. 4.
User's Guide - 1810.book Page 40 Monday, September 10, 2007 6:39 PM Connecting an S-Video Source 1. Locate an S-video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 10). 2. Connect the cable to the S-video connector on your player and the S-Video connector on the projector: 3. If you want to play sound through the projector, see page 44 for instructions on connecting audio cables. 4.
User's Guide - 1810.book Page 41 Monday, September 10, 2007 6:39 PM Connecting a Component Video Source You will need a special cable to connect your component video equipment to the HD15 (VGA-style) connector on the projector. You can order the HD15 to component cable (ELPKC19) from Epson; see page 11 for more information. 1. Locate an HD15 to component video cable or adapter. 2. Connect the cable to your player and the Computer 1 or Computer 2 connector on the projector.
User's Guide - 1810.book Page 42 Monday, September 10, 2007 6:39 PM Connecting an RGB Video Source note Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 1. Locate the VGA computer cable provided with the projector. 2. Connect the cable to the video port on your player and the Computer1 or Computer2 port on the projector. 3.
User's Guide - 1810.book Page 43 Monday, September 10, 2007 6:39 PM Connecting an External Monitor If you want to monitor your computer presentation close-up (on a monitor placed beside the projector) as well as on the screen, you can connect an external monitor. You can use it to check on your presentation even if you’ve pressed the A/V Mute button or switched to a different picture source. First make sure your computer’s VGA cable is connected to the projector’s Computer1 port (see page 36).
User's Guide - 1810.book Page 44 Monday, September 10, 2007 6:39 PM Playing Sound Through the Projector You can play sound through the projector’s speaker system or attach an external speaker system. To play sound through the projector, follow these steps: 1. Locate the appropriate cable and connect it to the Audio jack on the projector. ■ If you have equipment connected to the Computer 1 or Computer 2 port, use a stereo mini-jack cable.
User's Guide - 1810.book Page 45 Monday, September 10, 2007 6:39 PM Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end.
User's Guide - 1810.
User's Guide - 1810.book Page 47 Monday, September 10, 2007 6:39 PM 4 Fine-Tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
User's Guide - 1810.book Page 48 Monday, September 10, 2007 6:39 PM Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list note The Network menu does not appear on the 1810p.
User's Guide - 1810.book Page 49 Monday, September 10, 2007 6:39 PM 4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. 5.
User's Guide - 1810.book Page 50 Monday, September 10, 2007 6:39 PM Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see the Image menu screen. 2. Use the pointer button to highlight the desired option, then adjust it as needed: note The available settings vary depending on the input source selected.
User's Guide - 1810.book Page 51 Monday, September 10, 2007 6:39 PM sRGB: For matching the color palette of standard sRGB computer displays. Blackboard: For projecting accurate colors on a green chalkboard (adjusts the white point). note Customized: For manual color adjustment (see below). ■ The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness.
User's Guide - 1810.book Page 52 Monday, September 10, 2007 6:39 PM 2. Press the Enter button to select Customized, then press Esc to return to the Image menu. 3. Select Color Adjustment and press Enter. You see hue and saturation controls on the screen for six colors: RGBCMY (red, green, blue, cyan, magenta, and yellow). 4. Select the color axis you want to adjust and press Enter. You see color controls for hue and saturation.
User's Guide - 1810.book Page 53 Monday, September 10, 2007 6:39 PM 2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Auto Setup Leave this setting On to automatically optimize computer images. Turn it off if you want to save adjustments you have made to the Tracking, Sync, and Position settings. ■ Tracking Adjust this value to eliminate vertical stripes in computer images. ■ Sync Adjust this value if computer images appear blurry or flicker.
User's Guide - 1810.book Page 54 Monday, September 10, 2007 6:39 PM Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Adjusts the shape of the image if the projector has been tilted upward or placed at an angle to the screen. Select H/V-Keystone to correct horizontal and vertical keystone distortion, or to turn Auto V-Keystone on or off (see page 24).
User's Guide - 1810.book Page 55 Monday, September 10, 2007 6:39 PM ■ Remote Receiver Deactivates the projector’s front and/or back sensors that detect signals from the remote control. Use this setting to prevent use of the remote control or to stop interference from bright fluorescent lights. ■ Test Pattern Displays a test pattern for use when adjusting the zoom and focus, and when performing keystone correction.
User's Guide - 1810.book Page 56 Monday, September 10, 2007 6:39 PM You see this screen: note Network Protect is not available for the 1810p projector. 2. Use the Hold down pointer button to select Password and press Enter. 3. When you see a message asking if you want to change the password, select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric keypad to enter a four digit password. (The default setting is 0000.) 5.
User's Guide - 1810.book Page 57 Monday, September 10, 2007 6:39 PM Starting the Projector with a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: note If you leave the projector plugged in, the Password Protect Release screen will not appear. It appears only if you unplug and reconnect the power cable.
User's Guide - 1810.book Page 58 Monday, September 10, 2007 6:39 PM Capturing the Image Start by displaying the image you want to use from either a computer or video source, such as a DVD player. Then follow these steps to capture the image and transfer it to the projector: note When you choose an image for the user’s logo, it erases any previously used image. You can save an image up to 300 × 400 pixels in size. 1.
User's Guide - 1810.book Page 59 Monday, September 10, 2007 6:39 PM Choosing When to Display the Image After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the A/V Mute button (see page 29). 1. Press the Menu button, highlight the Extended menu, and press Enter. 2. Select Display and press Enter. 3.
User's Guide - 1810.book Page 60 Monday, September 10, 2007 6:39 PM Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations. ■ Display Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display. ■ User’s Logo Create a custom startup screen, as described on page 57.
User's Guide - 1810.book Page 61 Monday, September 10, 2007 6:39 PM minutes or when the A/V mute slide (lens cover) is closed. Enable High Altitude Mode when you are using the projector above 4900 ft (1500 m). ■ Standby Mode This function is not used for the PowerLite 1810p. ■ Projector ID Lets you assign a numeric ID to each projector. When you are using multiple projectors, you can use the ID to select the one you want to operate with the remote control. See page 33 for instructions.
User's Guide - 1810.book Page 62 Monday, September 10, 2007 6:39 PM Multi-screen Color Adjustment You can match the color of projected images when two or more projectors are being used to display images near each other. For each screen, you can set five levels of brightness and color correction. note If you use two or more projectors side-by-side, exhaust from adjacent projectors might cause overheating. Leave at least 2 feet (60 cm) of space between projectors. 1.
User's Guide - 1810.book Page 63 Monday, September 10, 2007 6:39 PM 5 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover.
User's Guide - 1810.book Page 64 Monday, September 10, 2007 6:39 PM Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Use a canister of compressed air to remove dust. To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.
User's Guide - 1810.book Page 65 Monday, September 10, 2007 6:39 PM Cleaning the Air Filter and Vent Your projector includes an air filter to ensure the best performance. If dust collects on the air filter (on the bottom of the projector) or vent (on the front of the projector), clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector. Follow these steps: note To order replacement air filters, request part number V13H134A08.
User's Guide - 1810.book Page 66 Monday, September 10, 2007 6:39 PM Replacing the Lamp and Air Filter note When you get a replacement lamp for your projector, you should replace the filter. Turn off this product when not in use to prolong the life of the projector. The life span of the projection lamp is about 2500 hours if Brightness Control in the Settings menu is set to High (default), and 3000 hours if Brightness Control is set to Low. See page 69 to check the lamp usage.
User's Guide - 1810.book Page 67 Monday, September 10, 2007 6:39 PM Follow these steps to replace the lamp and air filter: warning 1. Turn off the projector and unplug the power cord. 2. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use. 3. Loosen the lamp cover screw (you don’t need to remove it). Then slide the lamp cover to the side and lift it off of the projector. 4.
User's Guide - 1810.book Page 68 Monday, September 10, 2007 6:39 PM 5. Hold the lamp as shown and pull it straight out. note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.) 7. Once the lamp is fully inserted, tighten its screws. 8. Replace the lamp cover, then tighten its screw. 9.
User's Guide - 1810.book Page 69 Monday, September 10, 2007 6:39 PM Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menus. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3. Select Reset Lamp Hours and press Enter. 4.
User's Guide - 1810.book Page 70 Monday, September 10, 2007 6:39 PM The life span of the lamp is about 2500 hours if the Brightness Control setting in the Settings menu is set to High (default), and 3000 hours if the Brightness Control setting is set to Low. Make sure you have a spare lamp handy if the usage hours on this menu are close to the life span of your lamp.
User's Guide - 1810.book Page 71 Monday, September 10, 2007 6:39 PM Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
User's Guide - 1810.
User's Guide - 1810.book Page 73 Monday, September 10, 2007 6:39 PM 6 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
User's Guide - 1810.book Page 74 Monday, September 10, 2007 6:39 PM Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on top of the projector or on the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help menu: 2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items. 3.
User's Guide - 1810.book Page 75 Monday, September 10, 2007 6:39 PM Checking Projector Status If your projector isn’t working correctly, first turn it off, wait for it to cool (the Power light stops flashing orange), and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
User's Guide - 1810.book Page 76 Monday, September 10, 2007 6:39 PM Status lights (continued) Light Status Description Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filter and vents are clear. Red The projector is overheating, which turns the lamp off automatically.
User's Guide - 1810.book Page 77 Monday, September 10, 2007 6:39 PM Solving Projector Operation Problems The power doesn’t turn on. ■ If the projector doesn’t turn on when you press the P Power button, make sure the power cable is connected to the projector and plugged into a working electrical outlet. ■ The power cable may be defective. Disconnect the cable from the outlet and contact Epson as described on page 83. ■ Check to see if the A/V mute slide (lens cover) is closed.
User's Guide - 1810.book Page 78 Monday, September 10, 2007 6:39 PM ■ If you are projecting from a DVD player or other video source, make sure you turn it on and press its Play button. You’ve connected a computer and see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described on page 36.
User's Guide - 1810.book Page 79 Monday, September 10, 2007 6:39 PM The message Not Supported is displayed. ■ Make sure the correct input signal is selected in the Signal menu (see page 52). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200) and the frequency or refresh rate is supported by the projector (see page 89). If necessary, change your computer’s resolution setting. Only part of the computer image is displayed. ■ Press the Auto button on the remote control.
User's Guide - 1810.book Page 80 Monday, September 10, 2007 6:39 PM The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet, or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector.
User's Guide - 1810.book Page 81 Monday, September 10, 2007 6:39 PM You see vertical bands or the image still looks blurry after trying the solutions in the previous section. ■ ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the Auto button on the remote control or the Enter button on the projector to reset the projector’s Tracking, Sync, and Position settings.
User's Guide - 1810.book Page 82 Monday, September 10, 2007 6:39 PM ■ Try adjusting the Brightness and Contrast settings on the Image menu. ■ Check your computer display settings to correct the color balance. ■ The projector’s lamp may need to be replaced. See page 66 for instructions. ■ Make sure the correct input signal is selected in the Signal menu (see page 53). There is no sound, or the sound is not loud enough.
User's Guide - 1810.book Page 83 Monday, September 10, 2007 6:39 PM Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ The remote control’s batteries may not be installed correctly or may be low on power. To change the batteries, see page 70. ■ Make sure you are within about 20 feet (6 meters) of the projector and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below).
User's Guide - 1810.book Page 84 Monday, September 10, 2007 6:39 PM Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period.
User's Guide - 1810.book Page 85 Monday, September 10, 2007 6:39 PM A Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
User's Guide - 1810.book Page 86 Monday, September 10, 2007 6:39 PM The projector includes security features to prevent its theft when installed or used in public locations: ■ Security cable attachment You can attach a commercially available security cable as shown below to secure the projector to a table or ceiling mount. ■ Kensington security slot The security slot is compatible with the MicroSaver security systems manufactured by Kensington. You can purchase this lock from Epson (see page 11).
User's Guide - 1810.book Page 87 Monday, September 10, 2007 6:39 PM B Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 16.8 million colors Brightness 3500 lumens (High Brightness mode) 2700 lumens (Low Brightness mode) Contrast ratio 500:1 Image size 30 to 300 inches Projection distance 2.7 to 48.2 feet (0.8 to 14.
User's Guide - 1810.book Page 88 Monday, September 10, 2007 6:39 PM Projection Lamp note Lamp life results will vary depending upon mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. Type UHE (Ultra High Efficiency) Power consumption 210 W Lamp life Approx. 2500 hours (High Brightness mode) Approx.
User's Guide - 1810.book Page 89 Monday, September 10, 2007 6:39 PM Environmental Temperature Humidity (non-condensing) Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Operating: 20 to 80% RH Storage: 10 to 90% RH Operating altitude 0 to 7,500 ft (0 to 2,286 m) Safety and Approvals United States FCC 47CFR Part 15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.book Page 93 Monday, September 10, 2007 6:39 PM C Notices This appendix includes safety instructions and other important information about your projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes. ■ Do not place the projector on an unstable cart, stand, or table.
User's Guide - 1810.book Page 94 Monday, September 10, 2007 6:39 PM 94 Notices ■ Do not operate the projector in a closed-in cabinet unless proper ventilation is provided. ■ If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. ■ You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
User's Guide - 1810.book Page 95 Monday, September 10, 2007 6:39 PM ■ If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or coming in contact with the eyes or mouth. ■ If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes when you open the lamp cover.
User's Guide - 1810.book Page 96 Monday, September 10, 2007 6:39 PM For Canadian Users This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.
User's Guide - 1810.
