HSDPA USB Modem User Guide SDC-1000
Copyright Epivalley Co., Ltd has the copyright for this manual. This manual should not be reproduced or distributed with no prior written consent by Epivalley Co., Ltd. Registered Trademark The registered trademark stated in this manual is the registered trademark owned by the corresponding company. Confidential & Proprietary This manual is the technical property of Epivalley Co., Ltd and it is prohibited to copy or utilize the manual with no prior consent by the technical data department.
Table of Contents Cautions for Safety ………………… 4 Connecting with PC ……………………… 11 Introduction ………………………… 5 Checkig Connection ……………………… 12 Specific Features …………………………… 5 Epivalley HSDPA Dialer ………………… 12 Web …………………………………… SMS …………………………………… Address ………………………………… Setting ………………………………… Logs …………………………………… Terminating Program …………………… Configuration ………………………… 6 Condition for Use …………………………… 6 Name of Each Part ………………… 7 Installing Program ………………… 8 Deleting Program …………………… 9 12 13 16 17 18 18 Trouble
Cautions for Safety The cautions for safety are the contents to keep the safety of users and to prevent possible loss in property or convenience caused by accidents. The product should properly be used after sufficient understanding of the contents. Warning ● Do not discretionally disassemble, modify, or repair the product. ● Do not use the product if possible at the place where the use of handsets is prohibited.
Introduction Thanks you for purchasing SDC1000 of Epivalley Co., Ltd. SDC1000 is a USB Modem by HSDPA method to use wireless internet anytime and anywhere with no limit in time or place. * HSDPA (High Speed Downlink Packet Access): This is the mobile communication method for sending/receiving data at the speed significantly faster than that of W-CDMA or CDMA.
Configuration The configuration of SDC1000 product is as shown below: Main Body Manual USB Extension Cable * Note: The configuration of the product may be somewhat changed wit no prior notice to improve the functions of the product.
Name of Each Part Front Part Lateral Part Lower Part USIM Slot Slide knob LED Display Micro SD Slot USB Port USB Port 7
Installing Program S/W is included in USB Modem. 3. To install the program, files are copied from Modem to PC. 5. Designate the destination folder to install the program and click [Next] button. 1. When SDC1000 is inserted into the USB port of the PC to use SDC1000, the installation program is automatically run. * Note: If SDC1000 Dialer program is already installed, the program is not automatically run. If you want to reinstall the program, manually start the installation program with use of explorer. 2.
Deleting Program 7. Files are copied from Modem to PC. The method to delete Epivalley HSDPA Dialer installed in PC is as described below. 1. On the task bar, click [Start] - [Program] - [Epivalley] - [SDC1000_Dialer] - [Uninstall] in order. 8. Program is completely installed. Click [Finish] button to finish the program installation. 2. When a popup screen is displayed and it is asked whether to delete the program, click [Yes] button.
Using USIM USIM (universal subscriber identity module) consists of SIM (subscriber identity module) containing subscribers’ information and UICC (universal IC card) and various functions including user authentication, global roaming, and e-commerce are performed with a card. For proper use of SDC1000, USIM Card should be inserted.
Using SDC1000 Running Program Connecting with PC Run Epivalley HSDPA Dialer program be below-described method. The USB Port of SDC1000 is built in the main body. Pull out the USB Port and connect it with PC. 1. 1. Doubleclick the shortcut icon (Epivalley HSDPA Dialer) on the window. 3 1 4 Or on the task bar, click [Start] - [Program] - [Epivalley] - [SDC1000_Dialer] - [Epivalley HSDPA Dialer] in order. 2 * Note: When SDC1000 is not used, remove it from PC and push USB Port inside to be stored. 2.
Using SDC1000 Checkig Connection When SDC1000 is connected with PC, the connection status may be confirmed on the status display bar at the lowest part of the program. Ths status of product may also be checked on the LED at the side of SDC1000.
Using SDC1000 4. Select the profile created for internet connection and click [Connect] button. 3. Input Profile Name to create the profile for internet connection and input the information needed to connect with profile. Click [OK] button to create a profile. 5. Internet is connected and the time of internet use and packets may be checked. 13 ■ SMS [SMS] is the menu that is used in sending short messages or consfirming received short messages.
Using SDC1000 2. Write the message on Editor screen. 4. Click [Send] button the send the message. • Clear: erase the message written on Editor screen. • Templates: designates the templates of message • Emoticon: inputs emoticon. • Special: inputs special characters. When a message is received, the receipt is noticed on the Windows popup screen and, if the program is minized, the tray icon flashes.
Using SDC1000 • Sent In [Sent] tab, you can check the messages sent. The messages may be arranged by Date, Number, Content, Destination, and Message Status and the message may be relayed with clicking [Forward] button. Also, the destination (PC or USIM) where the messages are stored may be confirmed with the icon. * Note: Click [Save] button to store the telephone number to which the message was sent or change the destination to store the message.
Using SDC1000 ■ Address [Address] menu is used to register, edit, and delete telephone numbers. • Viewing Registered Telephone Numbers You can check the stored telephone numbers with selecting All, PC, or SIM tab and you can view the registered telephone numbers in the arrangement by Name, Mobile, Address, Office, Home, Fax, E-mail, and Comments. putting the search condition, and clicking [Search] button.
Using SDC1000 Drop and send a message to a group or groups at a time. Also, you can move or copy the registered telephone number by selecting the number and clicking the right button of mouse. ■ Setting In [Setting] menu, you can set the environment related with the use of Epivalley HSDPA Dialer program. • SMS In [SMS] tab, you can set the information on notice of message receipt and Spam message management.
Using SDC1000 • Lock In [Lock] tab, you can set the information related with lock function. ■ Logs Terminating Program In [Logs], you can check the information on the date and time of internet connection and the quantities of sent/received data in relation to use of internet. To terminate Epivalley HSDPA Dialer program, click at the right top of the program. Or click the right button of mouse on the tray icon and click [Exit] button.
Trouble Shooting If you informs the expected problems and solutions in relation to the use of SDC 1000, the troubleshooting will be prepared with referring to the related contents of other models.
Specification Specification will be prepared after confirming the final specification.
Warranty Let use be informed of the warranty policy of Epivalley.
CE User Information Hereby, Epivalley co., LTD. declares that this SDC-1000 is in compliance with the essential requirements and other relevant provisions of Directive1999/5/EC. FCC RF EXPOSURE INFORMATION This USB modem is approved for use in normal size laptop computers only (typically with 12” or larger display screens).