User's Manual

ManualsBrandsEnterprise Electronics ManualsElectronicsKEYPAD TRANSMITTER

All 2005 to Present Model Year Ford/Mercury/Lincoln Vehicles With Keyless Remote Entry System

INSTALLATION

RF Keypad

ALL 2005 TO PRESENT MODEL YEAR FORD/MERCURY/LINCOLN VEHICLES WITH

KEYLESS REMOTE ENTRY SYSTEM

1. Please read ALL of these instructions before proceeding.

A. Program the RF Keypad to Your Vehicle

NOTE: It is easier to program the keypad prior to attaching it to the vehicle.

After five seconds of idle time, the keypad will reset itself.

NOTE: You must have all remote entry transmitters available before beginning this procedure, Fobs and RF

keypads. Check owners guide ‘‘Locks and Security’’ for maximum remote entry transmitters allowed, and

proper key positions.

If all remote entry transmitters are not present during the programming procedure, the missing

transmitters will not work following programming.

NOTE: The vehicle will exit programming mode after 20 seconds of inactivity.

NOTE: Ensure the brake pedal is not depressed during this procedure; the electronic signal could interfere with

programming.

Focus 2007 and Earlier Model Years (For all other vehicles proceed to “All Other Vehicles”)

2. Make sure that you have all of the Fobs and RF keypads for this vehicle.

3. Insert a key in the ignition.

4. Turn the key from the OFF position to the RUN (not START) position four times within six

seconds.

The fourth turn must end in the OFF position

The system will chime to confirm the vehicle is in programming mode.

5. Within 20 seconds of completing the previous step, press any button on Fob 1, if equipped.

The system will chime once, to confirm that the Fob has been programmed.

6. Within 20 seconds of completing the previous step, press any button on Fob 2, if equipped.

The system will chime once, to confirm that the Fob has been programmed.

7. Within 20 seconds of completing the previous step, press the 7/8 and 9/0 buttons simultaneously

on the RF keypad 1.

The system will chime once, to confirm that the RF keypad has been programmed.

Repeat this step if more than one RF keypad is used

8. After all remote entry transmitters have been programmed; turn the ignition to the RUN position

for the vehicle to exit programming mode.

Summary of content (4 pages)

PAGE 1
All 2005 to Present Model Year Ford/Mercury/Lincoln Vehicles With Keyless Remote Entry System INSTALLATION RF Keypad ALL 2005 TO PRESENT MODEL YEAR FORD/MERCURY/LINCOLN VEHICLES WITH KEYLESS REMOTE ENTRY SYSTEM 1. Please read ALL of these instructions before proceeding. A. Program the RF Keypad to Your Vehicle NOTE: It is easier to program the keypad prior to attaching it to the vehicle. After five seconds of idle time, the keypad will reset itself.
PAGE 2
All Other Vehicles NOTE: If your vehicle is equipped with Integrated Keyhead Transmitters IKTs, you do not need all the IKTs to program the RF keypad to your vehicle. 9. Make sure that you have all of the Fobs and RF keypads for this vehicle. 10. Unlock your vehicle electronically with the Fob or door unlock button. 11. Put a key in the ignition. 12. Turn the key from the OFF position to RUN (not START) position eight times within 10 seconds with the eighth turn ending in the RUN position.
PAGE 3
20. The vehicle doors will unlock-lock-unlock to confirm that your personal code has been programmed to the keypad and the 9/0 button will flash twice to confirm that the keypad has exited programming mode C. Adhering the Keypad to the Vehicle CAUTION: Do not adhere to moveable glass or windshield. NOTE: For proper adhesion, the mounting surface should be at least 60°F (15°C.) The tape is very sticky and will adhere quickly once contact is made.
PAGE 4
28. To lock all doors, press the 7/8 and the 9/0 keys simultaneously. You do not have to enter a 5-digit code. E. Changing the cover NOTE: The RF keypad kit comes with 2 covers (textured-black and primed). If a painted cover is desired, paint the primed cover to the desired color. 29. Remove the textured cover by prying at the corners with a plastic or wooden tool. Snap the painted cover into place. F. Low Power Warning 30.