(User’s Manual is Inside) How to Install How to Connect with TV How to connect with TV and the Stereo
How to Operate 1. Connect cable to TV (refer to “How To Install”) 2. Connect cable to this Product (when you connect cable make sure the arrow on the cable points to the top) 3. When you use an Adapter : Connect Adapter to cable adapter jack When using the battery microphone : Open the Back cover of the microphone, then insert 4 AA batteries (use Alkaline batteries) 4.
5. Turn microphone power ON. 6. When the TV shows the picture, select the number of the song, and then it will start to play the music. When you press the start/stop button once, it will start. When you press the button again, it will stop. 7. The product summary page will explain the microphone functions. 8. If there are only two holes for the external input in you TV (mono TV), put the yellow jack into the yellow hole and put the red or the white jack into the other hole.
PRODUCT SUMMARY 1. LCD display will show song selection number with the function icon.
2. / Up / Down button : When you press the up/down button, the song list will show on the screen. It is used to select the microphone, key, tempo, echo, and music sound, picture, musical instrument change and value. 3. MIC Microphone adjustment This button is also used to adjust the volume of the microphone. 4. RAN Random It is used to select a song at random. 5. F M FM radio channel set-up Press the FM key once, the LCD will show FM 106.3 and the TV monitor will show 106.3.
MODE ++ 2 Reservation Save After you reserve the favorite songs by using #8 of the reservation Function key, press the Mode key +2 to show it on the TV monitor : 1. Save reserved song 2. Remove reserved song 3. Play the reserved song 4. The End icon will show. Ending, if you press #1 & #4, the song will be saved. Even if the Power is off, the song stays in the system. To play the saved song, press the Mode key +2 & 3 for recall, then 4. • It can be saved up to 20 songs by the Reservation function.
T RO U BLE SH O O T IN G À W hen the Pow er doesn’t com e on ¢ U sing the A dapter ! Please confirm w hether the pow er sources are 100V or 200V . ! Check the contact point of the cable jack and the adapter jack. ! Reconnect the adapters. U sing the batteries ! D id you insert 4 A A batteries? ! M ake sure the inserted batteries ( + - ) are positioned in the correct direction. ! Check the elasticity of the stainless steel in the battery case. ! Check if the batteries are in good condition.
CAUTION 1. Do not store it in direct sunlight, high temperature, or moisture area. 2. Do not drop it or apply heavy impact. 3. When you cleaning, do not use alcoholic liquids or chemical solutions. Use only soft cloths. 4. Do not press hard on the LCD parts. 5. Never use sharp object on the keyboard. 6. Make sure to allow sufficient time for the unit to cool down before you play the instrument when you store it in the heated trunk(180F)of a car. 7. Do not disassemble the product. 8.
11. Image Color INDEX 256Color 12. Overflow Protection Circuit for Reverse Voltage 13. Operation temperature : -20°C+65°C HOW TO SET UP THE SONG PACK(OPTION) 1. Πρεσσ τηε βυττον ον τηε τοπ οφ τηε χοϖερ ανδ πυλλ δοων τηε βυττον οφ τηε χοϖερ οφ τηε βαχκ οφ τηε µιχροπηονε. 2. Αφτερ ψ ου τυρν οφφ τηε ποωερ, πλαχε τηε σονγ παχκ ασ σηοων (τηε αρροω ποιντσ τοπ ποσιτιον). 3. α) Ματχη τηε βοττοµ οφ τηε χοϖερ ωιτη τηατ οφ τηε µιχροπηονε βψ υσινγ τηε ριγητ ηανδ.
3. Χλοσε τηε βινδερ ρινγ. WIRELESS SUB-MICROPHONE USER MANUAL (OPTION) 1. Open the back cover, then plug the receiving pack as the diagram shown above 2. When pressing the Function Change + 3 button of the Main Microphone, the monitor will display the Sub-Microphone ON, and it will begin to function the channel. 3. Open the back cover of the Sub-Microphone, insert two AA batteries and press the power button. The Green LED light will be on and, it will start to function.
INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.