Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix K: Client: Models: Standards: ID’s: Report #: EnOcean GmbH TCM200C & TCM220C FCC 15.231/IC RSS-210 SZV-TCM2XXC/5713A-TCM2XXC 2008102 Manual Please see the following pages.
USER MANUAL V0.92 Transceiver Module TCM200C / 220C June 5, 2008 Patent protected: PRELI M I N ARY WO98/36395, DE 100 25 561, DE 101 50 128, WO 2004/051591, DE 103 01 678 A1, DE 10309334, WO 04/109236, WO 05/096482, WO 02/095707, US 6,747,573, US 7,019,241 EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications TCM200C / 220C User Manual V0.
USER MANUAL V0.92 TCM200C / 220C REVI SI ON H I STORY The following major modifications and improvements have been made to the first version of this document: No 0.92 0.93 M a j or Cha n ge s Corrected: No internal pull-up on IN_5 Agency Certification section added Pu blish e d by En Oce a n Gm bH , Kolpingr ing 1 8 a , 8 2 0 4 1 Obe r h a ch in g, Ge r m a n y w w w .e noce a n.com , info@e nocea n.
USER MANUAL V0.92 TCM200C / 220C TABLE OF CON TEN T 1 1.1 1.2 1.3 1.4 1.5 GENERAL DESCRIPTION ............................................................................... 4 Basic Functionality ....................................................................................... 4 Technical Data ............................................................................................ 4 Physical Dimensions ....................................................................................
USER MANUAL V0.92 TCM200C / 220C 1 GEN ERAL D ESCRI PTI ON 1 .1 Ba sic Fu n ct ion a lit y The transceiver modules TCM 200C and TCM 220C of EnOcean enable the realization of highly efficient RF repeaters and transceivers for the EnOcean 315 MHz radio system. The module receives all signals of the EnOcean radio transmitters and makes them available at the serial port. In addition a repeater functionality can be activated. Using API200 it is possible to write custom software for the module.
USER MANUAL V0.92 TCM200C / 220C PP5 PP4 PP3 ANT1 ANT2 PP2 Ph ysica l D im e n sion s PP1 1 .3 GND IN_0 IN_1 IN_2 IN_3 IN_4 IN_5 OUT_0 OUT_1 OUT_2 OUT_3 OUT_4 RXD n.c. VCC GND GND TCM200C/TCM220C Dimensions (mm) 18.0 x 36.5 mm PCB dim e nsions ( w it hout pin con ne ct or ) 16 pins, grid 2.0 mm (4.0 mm in length, Pin conne ct or 1 .4 En vir on m e n t a l Con dit ion s -25°C … +65 °C Ope r a t ing t e m pe ra t ur e -40°C up … +85 °C St or a ge t e m pe ra t u r e 0% … 95% r.h.
USER MANUAL V0.92 TCM200C / 220C 2 FUN CTI ON AL D ESCRI PTI ON 2 .1 Block D ia gr a m IN_0..5 RF Transceiver OUT_0..4 µC ANT Voltage regulator PP1..5 (TCM200C only) VCC EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com GND Subject to modifications TCM200C / 220C User Manual V0.
USER MANUAL V0.92 TCM200C / 220C 2 .2 Pin D e scr ipt ion a n d ope ra t ion a l ch a r a ct e r ist ics Pin 1 2 3 4 5 6 Sym bol GND IN_0 IN_1 IN_2 IN_3 IN_4 7 IN_5 8 9 10 11 OUT_0 OUT_1 OUT_2 OUT_3 12 OUT_4 13 14 15 16 RXD n.c.
USER MANUAL V0.92 TCM200C / 220C 2 .3 Absolu t e m a x im u m r a t in gs Symbol Description VCC Supply Voltage (Note 1) OUT_0 Output 0 (Note 2) Parameter TCM200C OUT_4 Units min. max. min. max. VCC -0.3 5.5 -0.3 3.6 Voltage -0.3 60 -0.3 VCC+0.3 V ± 25 mA Current OUT_1..3 TCM220C Output 1..3 (Note 2) Voltage Output source or sink current Current Max. load current Current Output 4 (Note 3) Voltage Output diode current Current 200 -0.3 60 -0.
USER MANUAL V0.92 TCM200C / 220C 2 .4 Equ iva le n t sch e m a t ics 2 .4 .1 Ope n dr a in out put s OUT_ 0 ..3 ( TCM 2 0 0 C on ly) OUT_x external (OD) 2 .5 OUT_x internal (TTL) Tr a n sm it t im in g ( on ly in re pe a t e r m ode ) The setup of the transmission timing allows avoiding possible collisions with data packages of other EnOcean transmitters as well as disturbances from the environment. With each transmission cycle, 3 identical subtelegrams are transmitted.
USER MANUAL V0.92 TCM200C / 220C 3 APPLI CATI ON S I N FORM ATI ON 3 .1 Tr a n sm ission ra n ge The main factors that influence the system transmission range are type and location of the antennas of the receiver and the transmitter, type of terrain and degree of obstruction of the link path, sources of interference affecting the receiver, and “Dead” spots caused by signal reflections from nearby conductive objects.
USER MANUAL V0.92 TCM200C / 220C 3 .2 M ou n t in g t h e a n t e n n a Positioning and choice of receiver and transmitter antennas are the most important factors in determining system transmission range. TCM200C and TCM220C are providing two antenna outputs, ANT1 and ANT2: ANT1 is designed for use with a 15cm whip antenna ANT2 is designed for use with 50Ω antennas, e.g. helix antenna or external antenna 3 .2 .
USER MANUAL V0.92 TCM200C / 220C Recommendations for laying the antenna: PCB with GND 9 PCB without GND The GND plane should have a size of at least 5cm x 8cm Antenna too close to GND area 9 9 Antenna end led back to foot point Antenna too close to GND area 9 EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications TCM200C / 220C User Manual V0.
USER MANUAL V0.92 TCM200C / 220C 3 .2 .2 M ou nt in g 5 0 Ω a nt enn a s For mounting the receiver at bad RF locations (e.g. within a metal cabinet), an external antenna has to be used. Unsolder the whip antenna (if already mounted) Connect external antenna to the module by 50Ω coax cable with Teflon insulation Connect the inner cable to the ANT2 antenna hole on the PCB Solder the shielding as short as possible to the antenna GND pad (length of insulation max.
USER MANUAL V0.92 TCM200C / 220C 3 .4 Con n e ct in g Ope n Colle ct or or Ope n D r a in Ou t pu t s The term open-collector typically refers to a transistor output where the collector output (collector for bipolar transistors, drain for MOSFETs) of the transistor is not yet connected to a positive voltage internally. Since a transistor used in an output is typically a saturated switch, the collector needs to be connected to a positive voltage to complete the circuit.
USER MANUAL V0.92 TCM200C / 220C +12V +5V 15 VCC 8 OUT_0 TCM 2 0 0 C GND 16 Ex a m ple for con n e ct ion of a r e la y t o a n ope n colle ct or / dra in ou t put 3 .
USER MANUAL V0.92 TCM200C / 220C The distance between EnOcean receivers and other transmitting devices such as computers, audio and video equipment that also emit high-frequency signals should be at least 1m. A summarized application note to determine the transmission range within buildings is available as download from www.enocean.com. EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.
USER MANUAL V0.92 TCM200C / 220C 3 .6 AGEN CY CERTI FI CATI ON S 3 .6 .1 FCC ( Un it e d St a t e s) Ce r t ifica t ion TCM 2 0 0 C a n d TCM 2 2 0 C LI M I TED M OD ULAR APPROVAL This is an RF module approved for Limited Modular use operating as an intentional transmitting device with respect to 47 CFR 15.231(a-c) and is limited to OEM installation. The module is optimized to operate using small amounts of energy, and may be powered by a battery.
USER MANUAL V0.92 TCM200C / 220C OEM Re quir e m e nt s In order to use EnOcean’s FCC ID number, the OEM must ensure that the following conditions are met: End users of products, which contain the module must not have the ability to alter the firmware that governs the operation of the module. The agency grant is valid only when the module is incorporated into a final product by OEM integrators. The end-user must not be provided with instructions to remove, adjust or install the module.
USER MANUAL V0.92 TCM200C / 220C 4 D EVELOPM EN T TOOLS EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications TCM200C / 220C User Manual V0.
USER MANUAL V0.92 TCM200C / 220C APPEN D I X A.1 En Oce a n se r ia l pr ot ocol A.1 .1 M e ssa ge for m a t The following figure shows the message format. A data block of length n is composed of 2 synchronization bytes, 1 octet for the header and n-1 octets for the message data. Tx D Sync Sync Header Byte0 ByteN-1 ... M e ssa ge for m a t for a syn ch r onou s ser ia l com m u n ica t ion A.1 .
USER MANUAL V0.92 TCM200C / 220C A.1 .3 D e scr ipt ion of se r ia l da t a st r u ct u r e Bit 7 Bit 0 SYNC_BYTE1 (A5 Hex) SYNC_BYTE0 (5A Hex) H_SEQ LENGTH ORG DATA_BYTE3 DATA_BYTE2 DATA_BYTE1 DATA_BYTE0 ID_BYTE3 ID_BYTE2 ID_BYTE1 ID_BYTE0 STATUS CHECKSUM SYNC_BYTE 0..1 H_SEQ LENGTH ORG DATA_BYTE 0..3 ID_BYTE 0..
USER MANUAL V0.92 TCM200C / 220C A.1 .5 D e t a ile d de scr ipt ion of STATUS fie ld I f ORG = 5 ( Te le gr a m fr om a PTM sw it ch m odu le ) : 7 Re se r ve d 0 T2 1 NU RP_ COUN TER Reserved T21 (2 bit) (1 bit) NU RP_COUNTER (1 bit) (4 bit) =0..15 For future use T21=0 Æ PTM switch module of type 1, T21=1 Æ PTM switch module of type 2 NU=1 Æ N-message, NU=0 Æ U-message.
USER MANUAL V0.92 TCM200C / 220C A.1 .6 D e t a ile d de scr ipt ion of D ATA_ BYTE 3 ..0 fie lds I f ORG = 5 a n d N U = 1 ( N - m e ssa ge fr om a PTM sw it ch m odu le ) : DATA_BYTE2..
USER MANUAL V0.92 TCM200C / 220C I f ORG = 7 ( Te le gr a m fr om a 4 Byt e STM se n sor ) : DATA_BYTE3 DATA_BYTE2 DATA_BYTE1 DATA_BYTE0 Value of third sensor analog input (AD_2) Value of second sensor analog input (AD_1) Value of first sensor analog input (AD_0) Sensor digital inputs as follows: 7 0 D I _ 3 DI _ 2 D I _ 1 DI _ 0 Re se r ve d I f ORG = 8 ( Te le gr a m fr om a H RC t r a n sm it t e r ) : DATA_BYTE2..
