USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE PTM 535 / PTM 535U / PTM 535J EnOcean Transmitter Module 10.09.2020 Observe precautions! Electrostatic sensitive devices! Patent protected: WO98/36395, DE 100 25 561, DE 101 50 128, WO 2004/051591, DE 103 01 678 A1, DE 10309334, WO 04/109236, WO 05/096482, WO 02/095707, US 6,747,573, US 7,019,241 © 2019 EnOcean | www.enocean.com F-710-017, V1.0 PTM 535 / 535J User Manual | v1.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE REVISION HISTORY The following major modifications and improvements have been made to this document: Version 1.0 1.1 Author MKA MK/CB Reviewer MKA CB Date 23 May 2018 02 Aug 2018 1.2 MK/CB CB 14 Sep 2018 1.3 MK/CB CB 21 Nov 2018 1.4 MK/CB CB 27 May 2019 1.5 MK MKA / MH 10 Sep 2020 Major Changes Initial Release Configuration set and functional block diagram updated, additional minor changes e.g.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE TABLE OF CONTENT 1 General description ........................................................................................ 5 Product description ........................................................................................ 5 Product variants ............................................................................................ 5 Technical data ......................................................................
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 7 6.4.1 ARIB (Japan) certificate ........................................................................ 31 6.4.2 ARIB (Japan) regulatory requirements .................................................... 32 Product history............................................................................................ 33 © 2019 EnOcean | www.enocean.com F-710-017, V1.0 PTM 535 / 535J User Manual | v1.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 1 General description 1.1 Product description The radio transmitter module PTM 535, PTM 535U and PTM 535J from EnOcean enable the implementation of wireless sensors and switches without batteries. Key applications are handheld remote controls or industrial switches. 1.2 Product variants The following product variants are offered: ◼ PTM 535 Operating frequency 868.300 MHz ◼ PTM 535U Operating frequency 902.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 1.3 Technical data Power supply ECO 200 or equivalent energy pulse Antenna Pre-installed whip antenna Frequency / Modulation / Transmission power PTM 535 PTM 535U PTM 535J 868.300 MHz / ASK / +5 dBm 902.875 MHz / FSK / +4 dBm 928.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 1.6 Device drawing Figure 1 – PTM 535 outline © 2019 EnOcean | www.enocean.com F-710-017, V1.0 PTM 535 / 535J User Manual | v1.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 1.7 Environmental conditions Operating temperature -25 °C … +65 °C Storage temperature -40 °C … +85 °C Storage temperature in Tape & Reel -20 °C … +50 °C Humidity 1.8 0% … 93% r.h., non-condensing Ordering information Type PTM 535 PTM 535U PTM 535J Ordering Code S3001-A535 S3051-A535 S3061-A535 © 2019 EnOcean | www.enocean.com Frequency Note 868.300 MHz 902.875 MHz 928.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 2 Functional description 2.1 Functional Principle PTM 535 is designed to be powered by an ECO 200 kinetic energy harvester from EnOcean. PTM 535 can be mechanically connected to the contact springs of ECO 200 by means of its integrated PCB contacts. PTM 535 provides 4 digital input pads and two PCB meander structures allowing the implementation of push button functions either via external connection or via conductive rubber pads.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 2.3 Interface pin layout Figure 3 below shows the pin out and external interfaces of PTM 535 as seen from the top (component side). Items marked in green are on the component side while items in grey are on the bottom side.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 2.4 Interface pin functionality Table 1 below describes the PTM 535 interface pin functionality.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 3 Radio telegram format 3.1 Standard mode In standard configuration, PTM 535 transmits the same telegram type as the PTM 210 pushbutton module. The telegram information is encoded within a 7 byte RPS telegram as shown in Figure 4 below.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE If one or two buttons are pressed, then the button status is transmitted using a so-called N-Message. The DATA field format of such N-Message is shown in Figure 6 below. Figure 6 – DATA field encoding for N-Messages (one or two button presses) If either no button is pressed (only the ECO 200 is actuated), three buttons are pressed or four buttons are pressed then the button status is transmitted using a so-called U-Message.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 3.2 Enhanced security mode While operating in enhanced security mode, PTM 535 sends secure telegrams in accordance to EEP D2-03-00 as specified in EnOcean Equipment Profiles. For more details refer to http://www.enocean-alliance.org/eep/.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 3.3 Switching between operation modes PTM 535 can be switched from standard mode (default) to enhanced security mode by connecting SECURE with VCC_MODE (see chapter 3 for details), and triggering the ECO 200. Upon entry into enhanced security mode, a teach-in telegram is sent by PTM 535. The type of the teach-in telegram (Teach_In_Info : Type) is: 1-PTM.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4 PTM 535 configuration PTM 535 provides a configuration interface that can be used to configure certain device parameters. Note that configuration is currently only supported for PTM 535 (868.300 MHz). Configuration of PTM 535U (902.875 MHz) and PTM 535J (928.350 MHz) is currently not supported. 4.1 PTM 535 configuration parameters The following parameters can be configured for PTM 535 (868.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.2 PTM 535 configuration interface The PTM 535 configuration interface consists of test points MP1- MP6. The function of these test points is summarized in Table 2 below.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.4 Connection between Segger J-Link and PTM 535 PTM 535 has to be connected to the Segger J-Link connector for configuration. Figure 9 below shows the pin-out of the Segger J-Link connector. Figure 9 – Segger J-Link connector pin-out Two approaches can be used to connect Segger J-Link and PTM 535 depending on the power supply of PTM 535 during configuration. Both approaches are described below. 4.4.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.4.2 External power supply (4 pin configuration interface) This approach allows you to use a 4 needle test adapter instead of a 6 needle adapter. Existing 4 needle adapters built for PTM 335 can be reused. It requires to supply PTM 535 by an external power supply (2.0 - 3.3 V) connected to PTM 535 MP1 and to Segger VTref (IO voltage reference). The external power supply ground has to be connected to PTM 535 MP2 (GND) and Segger GND.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.5 Required tools The following tools are required to configure PTM 535: ◼ Needle adapter Suitable adapter to contact test points as described in the previous chapter. EnOcean can provide a mechanical design example upon request. ◼ Debugger / Programmer J-Link Plus or higher from Segger is required, see: https://www.segger.com/products/debug-probes/j-link/models/j-link-plus/ ◼ J-Link Software and Documentation Pack https://www.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.6 Configuration setup Figure 12 below shows the setup required to configure PTM 535. USB Segger J-Link Plus Adapter PTM 535 PTM 535 Config + Segger SW Figure 12 – Setup for PTM 535 configuration 4.7 User Interface Figure 13 below shows the user interface of the PTM 535 Configurator. Figure 13 – User interface of PTM 535 Configurator © 2019 EnOcean | www.enocean.com F-710-017, V1.0 PTM 535 / 535J User Manual | v1.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 4.8 Execution sequence The following steps have to be executed exactly in the below given order: 1. “Get the device info” (show device info) 2. “Read PTM 535” the current configuration (show config and do a backup) 3. Modify the configuration fields (security key, telegram data, etc.) 4. “Write to PTM 535” the modified configuration Quit Segger info window with no (details see PTM Config help)! 5.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 5 Application information 5.1 Connection to ECO 200 energy harvester PTM 535 can be connected to ECO 200 without soldering. ECO 200 provides contact springs which can directly be connected to the corresponding contact pads of PTM 535. The contact pads on the bottom of the PCB are shown below (left). A second orientation where PTM 535 is rotated 180° with respect to ECO 200 is also possible as shown with dashed lines. 5.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 5.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 5.4 Layout recommendations PTM 535 can be soldered onto a host PCB. Figure 16 below shows the required footprint shape. EnOcean can provides Gerber data if required. Antenna PTM 535 Figure 16 – PCB footprint for PTM 535 Figure 17 below shows the required keep out area on a host PCB form PTM 535. No copper surface area is allowed within this area. Figure 17 – Keep out area on host PCB for PTM 535 © 2019 EnOcean | www.enocean.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 5.5 Transmission range The main factors that influence the system transmission range are type and location of the antennas of the receiver and the transmitter, type of terrain and degree of obstruction of the link path, sources of interference affecting the receiver, and “Dead” spots caused by signal reflections from nearby conductive objects.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6 Regulatory information PTM 535 has been tested according to standards for RED (European Union), FCC (United States), ISED (Canada) and ARIB (Japan) certification. 6.1 RED (European Union) The Radio Equipment Directive (2014/53/EU, typically referred to as RED) replaces the old R&TTE directive from 1999 as regulatory framework for radio products in the European Union.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6.2 6.2.1 FCC (United States) FCC certificate < To be inserted > 6.2.2 FCC regulatory statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6.3 6.3.1 ISED (Canada) ISED certificate 6.3.2 ISED regulatory statement 6.3.2.1 English version This radio transmitter has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6.3.2.2 French version PRUDENCE: Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6.4 ARIB (Japan) PTM 535J has been designed and tested to fulfil the approval requirements for ARIB STDT108 based on the built-in firmware. 6.4.1 ARIB (Japan) certificate The ARIB certificate is shown below. © 2019 EnOcean | www.enocean.com F-710-017, V1.0 PTM 535 / 535J User Manual | v1.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 6.4.2 ARIB (Japan) regulatory requirements When products using PTM 535 are placed on the Japanese market, they must carry the Specified Radio Equipment marking. PTM 535J will be laser marked on the bottom side of the PCB with the content shown in Table 3 below. Field 1 Content Description MODEL: PTM 535J xy A535–z dc Step Code „xy“ (z.B. CA) State Code „-z“ (z.B. -1); Date Code “dc” (z.B.
USER MANUAL PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 7 Product history Table 4 below outlines the product history of PTM 535 and indicates key changes made between different revisions. Revision PTM 535 CA-02 PTM 535 DA-03 PTM 535 DB-06 PTM 535 DB-07 PTM 535J DA-02 PTM 535U DA-02 Introduction Nov 2017 May 2018 Aug 2019 Jan 2020 Feb 2020 Oct 2020 Key features / changes Prototypes for lead customer evaluation First product release (868.
