Specifications

ManualsBrandsENFORCER ManualsElectronicsWireless Help Button

ENFORCER Wireless Help Button

4 SECO-LARM U.S.A., Inc.

LED does not light



Check battery connection

 Replace 9V battery

LED lights blue, but does not

activate lock

 Ensure Wireless Help Button is not housed in a metal box

 Test Wireless Help Button closer to the receiver

 Clear codes from receiver and re-learn wireless transmitter code

Channel RF Receiver

Button

Handheld

Transmitter

Room Monitor Kit

910RB2Q

919TP1H

BUQ

R100

KB1Q

Changing the Battery:

The Wireless Help Button has a multi-colored LED that illuminates blue when the button is pressed. When

the battery begins to run low, the LED will illuminate red. To change the battery:

1. Remove the two screws from the front of the plate and remove the plate from the back box.

2. Remove the battery clip from the 9V battery and remove the battery from the bracket.

3. Place the new battery in the bracket and snap the battery clip to the new battery.

4. Test the unit with the new battery. The LED should illuminate blue.

Put the plate back in the back

box and secure it to t

he back

box using the screws on the front.

Also Available from

FCC COMPLIANCE

STATEMENT

FCC ID: K4ER100TB

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)

THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the part

y responsible for compliance could void the user’s

authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the

device is permitted. Any change to the antenna or the device

could result in the device exceeding the RF exposure

requirements and void user’s authority to operate the device.

NOTICE

The SECO

LARM policy is one of continual development and improvement. For that reason, SECO

LARM

reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.

All trademarks

S.A., Inc. All

rights reserved.

WARRANTY:

This SECO

LARM

product is warranted against defects in material and workmanship while

used in normal

service for one (1) year from the date of sale to the original customer. SECO-

LARM’s obligation is limited to the repair or

replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

improper or abnormal usage, or faulty installation, or if for any other reason SECO-

LARM determines that such equipment

is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of

SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM

’s

option. In no event shall SECO-

LARM be liable for any special, collateral, incidental, or consequential personal or property

damage of any kind to the purchaser or anyone else.

Troubleshooting:

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone: (949) 261

2999 | (800) 662

0800

Email: sales@seco

larm.com

PITSW1

Order Part# 763

190

MI_RM

R100

TBQ_181211.docx

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies

with all national,

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM

will not be

held responsible for the use of this product in violation of any current laws or statutes.

RM-R100-TBQ

SD-862M-GWSQ

Wireless Help Button

Manual

Features:

*Actual operating range will vary greatly depending on the installation and operating environment.



Built-in RF transmitter:

- Powered by 9VDC (battery included)

- Range up to 250ft (76m)*, 433.92MHz

- Over 68 billion (6.8x10

) possible codes

- LED to indicate transmission and low battery

 Desktop or wall mounted



ABS Plastic single-gang plate with surface

mount back box

 Clear 2" square button

 "Push for Help" message plate included

 Requires RM-R100-KB1Q, or SK-910

(433.92MHz) series receiver

Summary of content (2 pages)

PAGE 1
ENFORCER Wireless Help Button Changing the Battery: The Wireless Help Button has a multi-colored LED that illuminates blue when the button is pressed. When the battery begins to run low, the LED will illuminate red. To change the battery: 1. 2. 3. 4. 5. Remove the two screws from the front of the plate and remove the plate from the back box. Remove the battery clip from the 9V battery and remove the battery from the bracket.
PAGE 2
ENFORCER Wireless Help Button ENFORCER Wireless Help Button Installation: Introduction: The ENFORCER Wireless Help Button can be used to wirelessly expand the Room Monitor (RM-R100-KB1Q) with a service/help button. The button is perfect for placing on a desktop, mounting on walls, or any other location where it is difficult to run wires. The Wireless Help Button combines the very best of SECO-LARM, flexible wireless solutions and reliable access control.