Installation Manual

ManualsBrandsENFORCER ManualsElectronicsWired Single-Channel RF Transmitter

Specifications

Type 1-Channel Wired RF Transmitter

Wiring

Switch Two 6" wires for N.O.

Power Two 6" wires for power input

Power

Battery 3VDC battery (CR-2032, included)

External

3~13 VDC output regulated

RF Frequency 315MHz*

Number of buttons 1

Channels 1

Possible codes Over 68 billion (6.8x10

)

Dimensions 1

"x2

" (31.5x55x8 mm)

Dimensions

Wired Single-Channel

RF Transmitter

SK-919T1-GBWQ*

Installation Manual

433.92

MHz

version also available

–

939T1

†

Actual range will vary greatly depending on the installation and operating environment

(55mm)

(8mm)

(31.5mm)

Electromagnetic lock

Make

any push

exit plate wireless

PUSH

EXIT

Receiver

Wall

PIR

SL-126Q

Strobe

Convert photobeam sensors with dry contacts

into an entry alert

Transmitter

Receiver

Transmitter

Wireless equipment / perimeter security

Transmitter

Receiver

Transmitter

Receiver

Wireless doorbell / service call button

PIR

Wall

Strobe

•

VDC output regulated adapter (not included)

• Frequency 315MHz*

• Operates up to 500ft (150m)

†

• Over 68 billion (6.8x10

) possible codes

• LED transmission indicator

• Includes one 3VDC lithium battery

(CR-2032)

• Compact size

• Compatible with all SECO-LARM SK-series

receivers of the same frequency

• Also available without logo –

SK-919T1-GBWUQ – 315MHz

SK-939T1-GBWUQ – 433.92MHz

Sample Applications

ENFORCER

ENFORCERENFORCER

ENFORCER Wired Single-Channel RF Transmitter

Installation

Power Connection

The wired transmitter can be powered by the factory preinstalled 3VDC lithium battery (CR-2032) or by

n external 3~13VDC output regulated adapter (not included).

If an external power adapter is preferred, connect the red and black wires of the wired transmitter to the

adapter's output wires, being careful to ensure correct polarity. The red wire is connected to the positive

and the black wire to the negative.

NOTES:

• T

he power input range of the wired transmitter is 3~13VDC and is polarity sensitive. Connecting

more than 13VDC or reversing the polarity will burn out the unit and void the warranty.

• Use only "regulated" adapters to power the wired transmitter.

• If using an external power adapter, the factory-installed lithium CR-2032 battery will serve as a

backup in case of power interruption (Battery must be removed for external inline power-on switch).

• If connected to an external power-on switch, it is suggested that you remove the battery to disable

the built-in button so that it can only be controlled by the power-on switch.

External Switch Connection

The wired transmitter can be controlled by its built-in button (see Fig. 1), by an external N.O. switch* only

(button, contact, or sensor, see Fig. 2), or by both (Fig. 3). To disable the built-in button, the external

switch must be installed inline to the positive terminal of the power source with the battery removed.

NOTES:

• Any wires not in use must be insulated to avoid a short-circuit

• Do not let the red wire touch any other wire. Doing so may burn out the transmitter.

*Switch not included

SECO-LARM

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone: (949) 261

2999 | (800) 662

0800

Email:

sales@seco

larm.com

PITSW1

Order Part#

762

121

MI_SK

9x9T1

GBWQ_210114

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale

to the original

customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-

LARM. This Warranty is void

if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or fau

lty installation, or if for any

other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workma

nship. The sole obligation of

SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-

LARM be liable for any

special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-

LARM reserves the right to change specifications without notice.

Inc.

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California

to cause cancer and birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

Fig. 1

Built

in button

–

Red

Black

Blue wires

†

Insulate unused wires

‡

AC Adapter optional

3~13 VDC

DC Soure

Fig. 3

External switch and

built-in button

–

Red

Black

Blue wires

†

Adapter optiona

. If not used,

insulate red and black wires.

3~13 VDC

Switch

Fig. 2

External

inline

power-on switch

–

Red

Black

Blue wires

†

Connect the blue wires

The

battery

must be removed in this situation.

3~13 VDC

Switch

FCC COMPLIANCE STATEMENT FCC ID: K4E919T2GDW

This device complies with part 15 of the FCC rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2)

this device must

accept any interference received, including interference that may cause undesired operation.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the de

vice

could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

DC Soure