User Manual 7 inch Wireless Video Door Phone 1
Directory Introduction……………………………………………………………………………………………2 Safety Warnings & Attentions……………………………………………………………… 2 Performance parameter………………………………………………………………………3-4 Product Diagram…………………………………………………………..….............................5 Installation Guide……………………………………………………..…..............................6-9 Attentions During Installation...........................................................................
Introduction Thank you for choosing this wireless video door phone. Please read this Manual carefully to fully understand its usage, perfect functions and simple operation. Before using this product, please read these Attentions carefully to ensure safe and proper operation of this product. The Company reserves the right to modify this Manual from time to time without prior notice.
Outdoor unit Power Customized lithium battery 3400mah Consumption 400mA Outline dimension 134*74*31mm Weight 122g Environmental condition -10℃~+50℃ Waterproof grade IP55 Placement Hang on outer wall beside the door Surface material ABS & hardware accessories Camera 300,000pixels View angle 120° wide angle Night vision pattern 2 IR lamp PIR 3m*100° Working time 7 hours continuously Standby time 2000 hours Charge time 6 hours External power AC9~16V/DC5~16V 4
Indoor monitor Power Customized lithium battery 4000mah Consumption 600mA Outline dimension 200*150*27mm Weight 387g Environmental condition 0℃~+40℃ Placement Put on table or hang on wall LCD size 7" TFT color screen Wireless communication mode 2.4GHz Frame rate 20fps Image Format JPEG Working time 6 hours continuously Standby time 800 hours Charge time 6.
Product Diagram Outdoor unit Indoor monitor 6
Installation Guide 1.outdoor unit shall be installed at 1.4~1.7 meter above the floor, and the camera shall avoid facing the sunlight directly. 2.Installation steps A.Fix the rain cover on the wall with screws. B.Put the outdoor unit into rain cover,and install the screw at the bottom. 3.Connect DC line according to the wiring diagram (the diameter of hole for wire getting through should be 16~30mm). Red wire (positive pole) connects to point 1; black wire (negative pole) connects to point 2.
4. Electronic lock and power supply connection, as show below: If electric lock maintains always open: connect to point 4 If electric lock maintains always close: connect to point 5 Two power lines of lock: one connects to lock, one connects point 6. Note: electric lock and external power supply should be prepared by user.
5. The camera lens can be adjustable. 6.
7. Table holder 8. Installation of Storage Card A. Insert the storage card with the correct way as shown in the diagram and you’ll hear a clicking sound B. Improper insertion of storage card may cause system failure, please confirm the correct inserting direction of the card. C.
Attentions During Installation Outdoor infrared sensor cannot be hidden or blocked by other objects. Do not expose the outdoor unit to direct sunlight. Install the cable correctly, otherwise the doorbell may be damaged. Storage cared introduction This product supports TF(micro-SD) card as external storage device, when there is no storage card in the product, the photo-taking and video-recording functions are impossible.
Indoor monitor Keys(Functions) OK ----ON/OFF ----Talking ---- work as confirm key for MENU EXIT ---work as monitor key for standby mode ----as exit key for MENU MENU ----work as unlock key when communicating with outdoor unit ----as right moving key for MENU ↑ ----work as option key for MENU ----as video key when calling or monitoring ----as option key when calling extension monitor ↓ ----work as option key for MENU, ----as photo key when calling or monitoring, ----as entrance key for exposure adj
Turn on/off Outdoor unit: Install the battery to turn on. Take out the battery to turn off.(DC/AC9-16V,Lithium battery)。 Indoor Unit: with 4000mah Lithium battery,DC/AC9-16V. Press the “OK” key for about 3S to turn on. Then, press the “OK” key for about 3S to enter shutdown interface: select“Yes” to turn off. UI operation instruction Press “MENU” key enter the main menu interface see&delete photo record. Can store 180pcs photos. Automatically cover the earliest photo when memory is full.
message for missed call or ring. Will have the message if miss any call or ring.Can store 10 messages at most.Message with photo(as setting) or video(as setting).Automatically cover the earliest message.It will not have new message if indoor unit is shutdown or power off. Ring setting.There is 4 default rings. MP3 format music in TF(micro-SD) card also can play. You can select the ring as you like(MP3 music name can not include Chinese characters).
Communication instruction Intercom between indoor unit and outdoor unit. Under standby status,press “Call”of out door unit--Indoor unit will ring-Show on screen--Press “OK” key, and show on the screen, then can talk with each other. To call/monitor the outdoor unit is to press EXIT the screen, which means not able to intercom. Press show , if show the EXIT on again, it will on the screen, which means can intercom with the outdoor unit. Under intercom state, press ↓ to take photo.
the number stands for different indoor unit.The green lines stands for intercom signal. When stand by, press PIR: when turn on the motion sensor, outdoor unit camera sense person EXIT key to monitor outside. within 2 meters and will take 3pcs photos record (require TF card inside) automatically. Anti-tamper alarm of outdoor unit. When rain cover separate from device, it will alarm with big sound. At the same time, will take 5pcs photos record. Will show on screen.
1V2 (add the 2nd monitor)- Match code : Select “Give code ” on the 1st paired indoor monitor --press OK key--enter into the giving code mode. On the new (second) indoor monitor, select “receive code” -- press OK key. It will have “di-di-di” three sounds, and displays ”Successful” on the screen, which means matching the 2nd monitor ok. 1V3(add the 3rd monitor) - Match code: Select “Give code ” on the 2nd paired indoor monitor –press OK key-- enter into the giving code mode.
Package Include Outdoor unit *1 Indoor monitor *1 Manual *1 Rain cover *1 Wall hang holder *1 Charger *2 DC line *1 Lithium battery 3400mA/h *1 Lithium battery 4000mA/h *1 Screw M3 *1 Statement The standard configuration for door phone is one indoor monitor and one outdoor unit. The door phone has finished code match and can be used directly.
General faults and solutions Fault Cause(s) Can not start up Solution(s) Neglected to press switch button Press switch button Lithium battery is not installed Install lithium battery Low battery Charge up lithium battery No connection to power adapter Connect to power adapter when battery runs out Adapter connector doesn’t Reconnect correctly connect to charging port of Can not charge Outdoor unit machine correctly Adapter doesn’t connect to 110V-- Plug into the socket to connect to 240V
FCC Statement for monitor(FCC ID: ERY266M7Q) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC Statement for camera(FCC ID: ERY266CAQ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.